What should I pay attention to when purchasing a woodworking engraving machine?

1.As long as the woodworking engraving machine and screw rod machine are aimed at the advertising industry, as long as the precision is high and the cost is low, but the speed is slow and the cutting strength is limited; The rack machine is mainly aimed at the woodworking industry and industries that need to cut vigorously, with fast speed and high strength, but low precision.

2.Woodworking engraving machine, servo engraving machine has high precision but is expensive, and ordinary engraving machine has average but moderate accuracy.

3.Woodworking engraving machine, track selection, there are square rails and round rails, square rails are generally imported from Taiwan, round rails are domestic followed by round guide rails, higher bearing capacity, average precision, but the cost of round guide rails is relatively low, the production cycle is short, easy to install and other characteristics. Compared with it, the bearing capacity of square rail is also high, the accuracy is also high, and it is slightly more expensive.

4.Woodworking engraving machine. Generally, the air-cooled spindle is suspended, because the hardness of the wood used in woodworking is not large, unlike marble, granite, jade, glass, etc., the hardness is relatively large, so the stone is best to use the water-cooled spindle, and the cooling speed is faster.

5.Woodworking engraving machine, whether it is vacuumed and adsorbed, this point is generally chosen by woodworking, because there are more carpentry fragments and fragments.

6.Woodworking engraving machine, whether it is long, if your production volume is relatively large, it is best to choose a multi-head, but then the length of use time, the accuracy of the engraving machine is limited, if the production volume is not very large, it is best to choose a single head, so that the use time is long, and the accuracy is good.

The above information is provided by Jinan Jufeng CNC Equipment Manufacturing Factory, specializing in the production of advertising engraving machines, woodworking engraving machines, laser engraving machines, stone engraving machines and other engraving machine equipment.

First of all, pay attention to whether the cable is a drag chain cable or not, because ordinary cables will not last long. There is also our factory specializing in the production of engraving machine cables, Beijing Zhongao Jingzhou cable. . . Provide quality assurance.

Summary. Hello let you wait for a long time woodworking engraving machine can process all kinds of wood, including oak, peach, poplar, walnut, beech, rosewood, maple, oak, mahogany, etc., as well as plastic, aluminum plate, glass, ceramics, stone, polycarbonate (PC), plexiglass, ABS and other materials, can process a variety of products, such as wood carving, wood carving, wood signage, wooden gifts, wooden packaging boxes, wood decorations, wooden tables and chairs and other furniture supplies, as well as a variety of decorative items, clothing items, packaging boxes, wood carving, Woodcarving, woodware, wooden signs, wooden handicrafts, wooden gifts, wooden handicrafts, wooden ornaments, wooden plastics, wooden ceramic supplies, wooden glass supplies, etc.

What products can be processed by a woodworking engraving machine.

Hello let you wait for a long time woodworking engraving machine can process all kinds of wood, including oak, peach, poplar, walnut, beech, rosewood, maple, oak, mahogany, etc., as well as plastic, aluminum plate, glass, ceramics, stone, polycarbonate (PC), plexiglass, ABS and other materials, can process a variety of products, such as wood carving, wood carving, wood signage, wooden gifts, wooden packaging boxes, wood decorations, wooden tables and chairs and other furniture supplies, as well as a variety of decorative items, clothing items, packaging boxes, wood carving, Woodcarving, woodware, wooden signs, wooden handicrafts, wooden gifts, wooden handicrafts, wooden ornaments, wooden plastics, wooden ceramic supplies, wooden glass supplies, etc.

The surface groove garden curvature can be used with an engraving machine.

Uh-huh, it shouldn't be a big problem.

The board refers to whether the knotted log can be synthesized at one time.

The knot log board can be synthesized with an engraving machine at one time, but the size and accuracy of the specific garden arc depends on the performance of the engraving machine, as well as the type, size and cutting edge angle of the installed knives, which also has a great impact on the setting and operation of the engraving machine. Therefore, in order to synthesize the groove garden arc of the knot log board at one time, it is necessary to comprehensively consider the performance of the engraving machine, the type, size and cutting edge angle of the cutter, as well as the technical level of the operator.

Knives ** to buy?

In general, woodworking engraving machine cutters can be bought in tool stores, hardware and building materials markets, wood markets, woodworking equipment specialty stores, and online purchases.

1. Open the computer system of the woodworking engraving machine, you need to use the grblcontrol software, and click the software as shown below on the computer screen.

2. After completing the above steps, double-click to open the software, and the interface is as follows. Click OK below (OK) at this time the software interface changes to the following figure, if the coordinates in the upper right corner are still gray, then repeat this step in the file bureau, and find the com port corresponding to the installed hardware in the device manager.

3. Click the mouse in the "Manual" area, and a drop-down interface will appear, as follows, use the mouse line to punctuate these directional buttons. The current display is "10", which can be adjusted from 100 to 100 in several steps, just click on the corresponding number.

4. Click the "spindle" on the right side of the software, as shown in the figure below: the current spindle speed setting value will be displayed as standard is 775 clicks, and the maximum spindle speed is 9000! The rotation speed is set to wax branches.

<> daily maintenance. The continuous operation time is less than 10 hours a day to ensure the cleaning of the cooling water and the normal operation of the water pump, and the water spindle motor must not be short of water, and the cooling water should be replaced regularly to prevent the water temperature from being too high. In winter, if the working environment temperature is too low, you can replace the water in the tank with antifreeze.

Note: X, Y, Z three-axis smooth rod with engine oil maintenance; The screw part is made of high-speed butter; If the working environment temperature is too low in winter, the PRTT ball screw and smooth rod (square guide rail or round guide rail) part should be rinsed and cleaned with gasoline first, and then add oil, otherwise it will cause excessive resistance of the transmission part of the machine and cause the machine to be misaligned. ）

When the electrical appliances are maintained and inspected, the power supply must be cut off, and the main circuit power indicator can be carried out only after the monitor has no display and the main circuit power indicator is turned off.

The engraving machine should be used for about three months to check the fasteners, and the connecting screws on both sides of the gantry, the fastening screws of the lead screw nut, and the fastening screws of the motors on both sides should be tightened.

With the expansion of production scale, the improvement of production accuracy, mechanized production lines, more and more woodworking enterprises, wooden door manufacturing, furniture companies and handicraft production companies, etc., the demand for woodworking engraving machines is increasing. As an emerging product of CNC woodworking engraving machine, training before use is a must, otherwise do not operate, otherwise it is easy to fail, and it will also damage the life of CNC woodworking engraving machine.

Learn the operation steps of CNC woodworking engraving machine:

1. Theoretical basis of CNC woodworking engraving machine:

The training must start from the theoretical training, and the operator must pass the theoretical assessment before the practical operation training. If the theoretical training is not passed, the operation training will not be carried out.

2. The use of CNC woodworking engraving machine tools

After the theoretical training, it is necessary to carry out the training of CNC woodworking engraving machine tools. The operator must be clear about the common tools, engraving motor speed, travel speed, precautions, etc., and the operator must be familiar with the application of the tool.

3. Application range of CNC woodworking engraving machine:

The operator must be familiar with the scope of the plate engraved by the CNC woodworking engraving machine, familiar with different materials, different thicknesses, different finished product sizes, etc. Familiarize yourself with different carving styles of different materials. 4. Operation of various software of CNC woodworking engraving machine:

Software training can only be carried out after passing the above training. The training of the software is mainly focused on the field of user application; For areas that are not needed by the user, they can learn on their own according to the training manual. The requirements for the software are:

Various layouts of the software, various operations, generation of paths, and errors that can be quickly found in the paths.

5. CNC woodworking engraving machine operation training: after the above various trainings, after the explanation of the trainers and the understanding and assessment of the operators: the operators are trained on the operation safety and operation precautions, and the operators can only carry out the CNC woodworking engraving machine test operation training after the trained personnel sign and approve the operation of the operation of the safety matters.

6. Training on various precautions for the operation of CNC woodworking engraving machine and maintenance of engraving machine.

Major decoration industry, industrial copy equipment accessories semi-finished product processing, bai musical instrument du industry, mold industry, handicraft industry, architectural model industry, advertising industry. Commonly used engraving materials wood, metal, foam, two-color board, organic board (acrylic), artificial stone, PVC board, wood, MDF, ABS.

Stone engraving machineMainly used in the stone industry: stone lettering, stone relief, stone yang carving, stone yin carving, stone line carving, stone cutting, stone hollowing, etc.

Carpentry carver masterTo be used in the woodworking industry: all kinds of doors, windows, cabinets, craft wooden doors, paint-free doors, screens, craft sash windows, corrugated board processing and other furniture, wood processing. Advertising Industry:

Advertising signage, sign production, advertising material cutting, blister molding, LED neon light production and other materials advertising decoration products production.

The above is provided by Xingcan CNC engraving machine manufacturers.

Engraving, cutting machine, punching.

The higher configuration can also be cut and cut.

Woodworking engraving machines are widely used in home decoration, furniture, advertising, mold industry I don't know what industry you are in