How does the engraving machine engrave a layer in layers, and the knife is 2 centimeters and a layer

The engraving machine engraves one layer down to two centimeters, and the other layer is 10 centimeters, which you can adjust, and you can use a few chainsaws of them according to the proportion.

The engraving machine is divided into a layer of carving knives, about 2 3 cm is very accurate, which is conducive to the extension of the service life of the engraving knife.

The engraving machine engraves abnormalities at a deep level, down to two to ten centimeters. This one has a scale, and you set it according to it, and then go down.

When making cutting files, the surface of the material is set to the knife, and the cutting depth is set to 20mm, and the feed depth of each layer is divided into several layers.

Now the engraving machine we divide into his carving layer down to his two centimeters layer of strength, but also can bring us all greater convenience and practicality.

How is the main accountant divided into a floating sheet scared by 2cm of ten centimeters, this carving has been there for a long time. Very accurate.

How to engrave the engraving machine layer by layer, down to the two people, for engraving this is a technical work, generally do not understand.

How to engrave a layer of carving machine down to two centimeters, a layer down to 10 centimeters, I think this should be in the manual.

Now the engraving machine also wants to divide its carving, its layer down to its two centimeters and one layer of strength, I think it can also give us all a better use.

The engraving machine engraves one layer down to two centimeters in layers.

The carving depth is 20, and the knife depth is set to 10, and it is divided into two cuts.

Go slower and rotate at a higher point, the main thing is that the knife is not good, and the tungsten steel spiral knife to be solved is absolutely OK, and it is absolutely OK to use it if it is not good.

The main thing is to use a good knife to make a good job.

If it is not said that some small knives can't get in, generally 6 centimeters is more appropriate, the speed is the highest, and the feed is slower.

Rotate faster, slower speed. You can change the knife to a better one.

Don't go too fast with a 6mm knife and you should be fine.

Single-edged spiral knives.

The 4 of them can be mainly positioned accurately.

The resistance is a little less.

Is it directly washed out of a U-shaped groove, or a pointed bottom, ordinary U-shaped groove, with an imported knife on the line, 7mm deep is very simple as long as the blade height is enough, if you want to engrave 2 cm of acrylic plate, then directly on the 4 imported knives, the key is not to know what your engraving machine is like, the lead screw or the rack and pinion, some engraving machines carved 1cm acrylic are very difficult, I use to engrave 1cm are running 50, but the knife must be imported knife, there are twenty or thirty, there are more than ten pieces, of course, the more expensive the better, carved fine, but also durable, if it is a V-shaped slot, then you have to use a big head knife, that is, the kind of V-shaped knife, but carved 7mm It is recommended that it is best to output it twice, the resistance of the knife is too great, I am afraid that the spindle can not stand it, and then it is a broken knife to hurt people, I hope it will help you.

The commonly used knives for carving acrylic are single-edged milling cutters and straight knives, and you use single-edged knives to do it.

There are two types of computer engraving machines: laser engraving and mechanical engraving, both of which are divided into high power and low power. Because the range of applications of engraving machines is very wide, it is necessary to know the most suitable range of applications for various engraving machines:

1. Badge: low-power laser engraving machine (seal engraving machine), high-power or low-power computer engraving machine;

2. Architectural model: large and low power computer engraving machine;

3. Metal (mold, chapter, etc.) processing: large and small power computer engraving machine (high power saves time due to the large amount of cutting each time);

4. Crystal word production: high-power laser engraving machine (more than 50w), high-power mechanical engraving machine;

5. Wood, plexiglass, artificial stone and other sign production: high-power mechanical engraving machine;

6. Display and exhibition model making: high-power, large-format mechanical engraving machine.

First of all, look at the specifications and dimensions of the engraving machine, what is the stroke, whether it can reach the stroke you need to engrave, and then see whether the machining parameters in the Weihong system parameters are set correctly to the maximum stroke.

Finally, if it has not been solved, call the engraving machine manufacturer to ask for a solution.

Absolutely, but it should be noted that the speed of the bottom pad is a little slower.

Hello, you can. But you have to have a straight knife of 12.

If it's roughing, try roughing cutters.

It's the kind of knife edge that has a notch.

Also, if your spindle doesn't have closed-loop speed regulation.

It is likely that the blockage has passed.

It is best to have a tool path that can handle corner speed reduction.

The last option, the f-value slows down...

If it doesn't work, use a knife of 6 to carve it twice and go down 1 cm at a time.

The speed of 12,000 to 16,000 is enough, and the speed can be faster.