Regarding the problem of decoration wiring, what problems need to be paid attention to when decorati

Hydropower totals about 7000, including the cost of slotting and the cost of water pipes and wires.

Of course, water pipes and wires are also good and bad, depending on how you identify them when you sign the contract. To put it simply, water pipes are divided into hot water and cold water, and the quality is definitely different for different manufacturers. The wire is a heavy load, and it should be thicker.

Finally, I would like to advise you, someone must be watching the decoration of your home, or it will not fool you. Not alarmist, listen to me, that's right.

A bit too high? This is not a bit of a high problem, home decoration 144 square meters of more than 7000 wiring?

I would like to ask you that your home is full of downlights? A room full of waits? The wall is full of outlets?

Or maybe all the wires are 4 square wires?

More than 7,000 is a bit too much, you talk to the boss of their company directly, generally speaking, according to the area of your home, about 4,000 yuan is enough (provided that the need for electricity is not very much!). ）

35 a meter Your house is not too high If you walk a lot There are tens of thousands of you are still 144 square meters I estimate that it is a local walk point.

It seems that you are all-inclusive, then you must be slaughtered! If you are looking for a decoration company, then let him send you the wiring diagram, and then you will know it by comparing it. Circuits are charged for auxiliary materials (conduits, elbows, cassettes), wires, switches, sockets, slots, and wiring.

The materials used can be found on the **; The rest is the labor cost, which is clear at a glance. If 7,000 blocks include the materials and labor I said, of course, depending on the brand, it's about the same.

If you pack the material, you will lose a lot, because the wire will definitely be unqualified!

If you don't include materials, then this ** is basically the line price! Labor is too expensive now!

If the concealed installation project is in Shenzhen, it seems that the slotting alone is 38 yuan.

That depends on your above standard, if it is a full package of water and electricity, it is not high, in Shanghai 144 square meters of panda wire, all with panda wire, if this standard is not high.

Does he make money by the square How much does a square cost?

When decorating a new house, every process is worthy of our attention, related to future use, every detail is important. The decoration of water and electricity wiring is the top priority in the whole rolling ridge home decoration. When decorating the water and electricity wiring, we need to pay attention to the following four points:

Choose high-quality insulator wires; Avoid early excavation of mutual land-backup nuclear joints between wires; Be careful not to destroy the waterproofing of the kitchen bathroom; Aesthetics of the overall wiring.

Decoration of water and electricity wiringIt is important to choose a wire with good insulation and voltage resistance. Generally, the wires that meet the national inspection standards have these two properties. So you need to go to a regular point to make a purchase.

If the electricity consumption at home is relatively high, you also need to pay attention to the number of current loads that the wire can carry. Select a larger number of loads.

2. Avoid connecting wires with each other

The second thing to pay attention to when decorating hydropower wiring is that it is necessary to avoid the joints of the wires when arranging the lines. The mutual connection of wires is a major hidden danger, on the one hand, it will reduce the insulation and increase the resistance of the wire; On the other hand, if there is a leakage, it increases the difficulty of maintenance and the chance of accidents. Therefore, when arranging the line, pay more attention to it, and you will be more assured of future use.

When decorating water and electricity wiring, you can't avoid the two spaces of kitchen and bathroom. When decorating water and electricity, the main thing to pay attention to is the layout of the kitchen and bathroom. Because these two places need to be waterproofed, we must pay strict attention to the waterproof problem when setting up the circuit.

The original waterproof structure cannot be damaged. Consider laying out the wiring on the wall.

The last thing you need to pay attention to when decorating water and electricity wiring is aesthetics. Safety comes first, but it also needs to be considered for overall aesthetics. The overall aesthetics are there, and it is more comfortable to live.

The problems that need to be paid attention to in the decoration of water and electricity wiring are introduced here, and some of the basics of decoration water and electricity can be easily understood when decorating.

You can get it for free

1. Reasonable wiring methods in home decoration.

1. Positioning: First of all, we must locate the circuit according to your use of electricity, for example, there are switches, there are sockets, there are lights, etc., and the electricians will locate them according to your requirements.

2. Slotting: After the positioning is completed, the electrician will open the wiring groove according to the positioning and circuit direction, and the wiring groove should be horizontal and vertical. However, the standard practice is not allowed to open the horizontal groove, because it will affect the bearing capacity of the wall.

3: Wiring: Wiring is generally buried in the wire pipe. There are two kinds of wire pipes: cold-bent pipe and PVC pipe, cold-bent pipe can be bent without breaking, which is the best choice for wiring, because its corner is curved, and the line can be replaced at any time without opening the wall.

Fourth, the elbow: the cold bending pipe should use a bending tool, and the arc should be 10 times the diameter of the line pipe, so that the threading or removal can be smooth.

Fourth, the principles to be followed in wiring:

1. The distance between strong and weak electricity should be 30---50 cm, and it can only be used as distant neighbors, not close relatives, otherwise it will cause interference.

2. Strong and weak electricity cannot be worn through the same tube.

3. The total cross-sectional area of the wire in the pipe should be less than 40% of the cross-sectional area of the protective pipe, for example, 20 pipes should wear up to 4 square wires.

4. Use the whole pipe as much as possible for long-distance line pipes.

5. If the line pipe needs to be connected, it is necessary to use joints, and the joints and pipes should be glued.

6. If there is a line pipe on the ground, it should be protected immediately to prevent it from cracking and affecting future maintenance.

7. When the wiring length is more than 15 meters or there are 3 bends in the middle, a junction box should be installed in the middle, because when disassembling and assembling the wire, it is too long or bent too much, and the wire cannot pass from the threading pipe. Under normal circumstances, the installation of air conditioning sockets should be more than 2 meters above the ground, and the wires and lines should be more than 40 cm away from the gas pipeline.

8. Under normal circumstances, the installation of air conditioning sockets should be more than 2 meters above the ground, and under normal circumstances, the installation of air conditioning sockets should be more than 2 meters above the ground.

9. Under the premise that there are no special requirements, the socket installation should be 30 cm above the ground.

10. The switch and socket should face the panel, and the live wire switch and socket should face the panel on the left side of the zero line and the right side of the live wire.

11. In home decoration, the wires can only be connected together, and the wiring should be strictly in accordance with the specifications.

12. The joint adopts the pressing wiring method, which must be strong and firm.

13. The connected wire should be wrapped with insulating tape immediately.

14. If the color of the live wire, zero wire and ground wire is determined, then the color can not be mixed at any time.

15. Lighting, sockets, air conditioners, water heaters and other circuits in different areas of the home should be separately grouped and wired, once which part needs to be off-power maintenance, it will not affect the normal use of other electrical appliances.

16. After the circuit is completed, be sure to ask the construction party to make a circuit layout diagram, once it is necessary to overhaul or repair the wall or nail the wall in the future to prevent the wire from being damaged.

With the shortest distance, the use of the least line, the maximum use is the most reasonable, professional electricians will generally use the simplest method to complete a more complex circuit distribution!

Generally, the water walks up and down the electricity.

1. Before construction, the electrical appliances and lighting equipment required in each functional area should be fully considered, and the corresponding matching wire cross-sectional area of each wire should be roughly calculated based on this. High-quality copper core sheath and junction box should be installed as much as possible to avoid aging and breakage, resulting in difficulty in panel installation.

2. Draw the circuit distribution map of each room, and determine the coordinates and height of various lamps, switches, sockets and switchboards to determine the direction of the route and the convergence of branches. It is advisable to use different colors for the wires so that they can identify the different circuits.

3. It is best to wear the power cord through the flame retardant pipe before laying. A power switch should be set outside the roof of the combustible structure for cutting off the power supply if necessary. The splices of all wires should be inside the junction box.

4. The total capacity of each branch of the indoor line should not exceed 3000 watts, and the load current of each single-phase circuit should be controlled within the appropriate range.

First, the use of light trough cable tray on the ceiling.

The light trough cable tray of the ceiling is mostly used in large buildings, and the prefabricated trough cable tray provides mechanical protection and support for horizontal cables.

Second, the ground trunking wiring method is adopted.

The ground trunking wiring method is suitable for the office with large openings, and there are dense ground information exits, so it is recommended to pre-embed the metal trunking or trunking floor in the ground cushion.

When decorating and laying wires, special attention should be paid to the layout of wires and wiring skills. When laying out the circuit, the designer will choose the circuit diagram, and that's it. It will clearly mark which lights, as well as the distribution of lights and sockets, are on the same line as the dot switches.

If you don't hire a designer, be sure to think about it thoroughly. In this way, the construction master will help you to pre-embed the wires according to your use requirements.

1.When laying indoor wiring, it is best to ask an experienced electrician or an electrician with an electrician network access certificate to do the electrical decoration for you. You'd better ask simple electrical questions to verify the expertise of the electrician who will lay out the circuit for you, such as how much current can pass through a square meter of wire, and then you can check online to see if he's accurate.

If there is a big gap between the electrician's and your problem, the electrician is not qualified.

2.The cost should also be considered when decorating, but the cost may be higher, but the safety is the best, and it is generally charged according to the length of the decoration. So there are also people who are short, how to take the route.

The main power switch is the main switch in your home, and when unplugged, it can cut off the power for your whole home. All buried wires are the main switch for this. When wiring indoors, the socket circuit and the lighting circuit should be routed separately.

The socket circuit circuit shall be made of plastic multi-strand soft copper wire, and the wire diameter shall not be less than square millimeters. As a rule of thumb, the wire diameter of a general household socket does not exceed the square millimeter.

3.When laying wires, try to avoid joints. Heat is generated due to the transient invasion of large resistance at the joint.

Assuming that a splice is really needed, it is necessary to do it precisely and the splice is tightly wrapped with insulating tape. A wall-mounted household distribution box is required at the entrance of each residence. The household distribution box is equipped with a main power switch, which can block the phase and neutral wires together, and there is a disconnect sign.

An energy meter should be set up in each house, and the energy meter box should be installed in the common area in layers. For wiring in the cooking area and bathroom, it is recommended not to lay strong electricity on the floor, try to wiring on the wall or top, because the kitchen and bathroom space consumes a lot of water and the floor is damp. If the wires are slotted in the floor, it will affect the waterproofing of the entire room.

The above is the answer to this question that should be paid special attention to when laying lines for decoration.

It should be noted that when decorating, we must pay attention to the layout of the wires, pay attention to the wiring skills, mark the distribution of lights and sockets, and pay attention to the same line as the switch.

It is necessary to pay attention to the length of the place where it appears, to avoid the waste of materials, to use better quality materials to decorate, and to pay special attention to the decoration when laying the line, so as not to leave too large a gap.

It is necessary to pay attention to the way and layout of wiring, to pay attention to the needs of your own life, to pay attention to the location of wiring to be reasonable, to pay attention to the cost of use, and to pay attention to safety issues.

When laying lines for decoration, it should be noted that the waterway and circuit should be isolated, and the distribution should be reasonable, and the work of waterproof and electricityproof should be done.

When the new house is installed in the system, how do you choose to go for the water and electricity decoration line? Many friends are always very entangled in the layout of the decoration line, because after all, the house is to live for decades, and it will be very troublesome in the future if you don't choose a good one! The problems that people are worried about are nothing more than safety factors, cost factors, maintenance problems, etc., which are all problems to be taken into account in the layout of the decoration line!

How to go to the decoration line? Next, let's analyze and compare with you!

First, the traditional decoration line layout of the old house decoration wiring method in the past is mostly chosen to lay on the ground or wall, which requires chiseling the ground or wall, and then the wire is concealed to deal with the way, this wiring method can ensure the normal life of everyone, and there will be no unsightly problems. However, this laying method has a big drawback, that is, when checking the circuit problem, you need to chisel the ground or wall, and if you really encounter this situation, it will be a great loss, and the human and financial resources are wasted more than a little bit!

Second, the advantages and disadvantages of the decoration line to go above (go to the top) If not according to the traditional way, we can also choose to go above the wiring mode, the circuit design of this way is relatively reasonable, in the later installation method, it will not destroy the circuit, and the safety of the circuit is well protected. However, there are also disadvantages to walking on the top, if all the wires are arranged on the top, it will cause a certain amount of pressure on the ceiling, and when there is a circuit problem that needs to be repaired, it is necessary to go to the house to remove the tiles, which is also very troublesome.

Third, the analysis of the suggestions on the line is good for the decoration line is better above or below, in fact, it is possible, there is no explicit provision on how to lay, the most important thing is to look at the actual effect of the cost estimate and the owner's consideration. As for the final choice of how to take the decoration line, it is still necessary to design the line according to the actual situation of the commercial house, and worry about the danger of moisture, corrosion and leakage below; There are limitations of the house structure when you go up, and you have to worry about whether the waterproof treatment design of the upstairs owner is appropriate. Many conscientious plumbers suggest that if you just set the line and don't casing, it is recommended that the circuit go up, and the water pipe will go directly to the lead, and the water and electricity pipelines are not recommended to have overlapping and intersecting places, and if there is really no way to avoid it, you must do insulation measures.

To sum up, there are pros and cons to the decoration line, whether it is above or below, mainly depending on the owner's preference and cost grasp! Personally, I still prefer to walk on it, it is easy to maintain, and the water leakage can be found in time without affecting the residents downstairs.