How to get the Mercedes Benz e300 ESP lights on

ESP is written as "Electronic Stability Program" in English. The vehicle control computer informs the driver of the working status of the ESP system through the ESP indicator light on the instrument panel. Normally, the ESP indicator should turn off automatically within a few seconds after starting the engine.

If the ESP indicator on the dashboard does not go off, the driver should judge and deal with it according to the following instructions according to the situation: ESP indicator light 1, the reason why the ESP indicator flashes is that the ESP system is activated, and the system is optimizing the dynamics of the car, thereby improving the steering stability of the vehicle. Second, the ESP indicator light is always on is usually accompanied by an audible signal and displays information on the instrument cluster screen.

The reason could be that the ESP button was pressed (possibly in the middle of the dashboard), the light on that button lit up, and the ESP system was turned off. At this time, the driver only needs to press the button again, turn on the ESP system to turn off the ESP light, the system enters the normal working state, and the indicator light on the ESP button goes off at the same time. When the vehicle starts, the ESP system is put into operation automatically.

If the ESP system is turned off, the system will be automatically turned on when the speed is greater than 50 km/h. If the ESP button is not pressed, the indicator light on the button lights up on its own, indicating that the ESP system is faulty, and the computer may have stored the corresponding fault code. The driver should take the vehicle to the workshop for maintenance.

ESP has a switch button, it is on the central control, if you accidentally turn off ESP it will be on, if you turn on ESP light is still on, then you have to go to the 4S store to check.

Teach you a good way. It's just to scare with a hammer. Then go to the insurance company to ask for compensation. And you can also get a new light! That's a good note, isn't it?

The display screen is not lit: there is a switch on the right side of the armrest controller, press the switch to try. If it still doesn't work, it may be central control.

The display freezes, you can restart the car and try it. If it still doesn't work after restarting, it may be a driving computer system or hardware failure, and it is recommended to go to a 4S shop for inspection and maintenance.

Here are some reasons why your car's display doesn't light up:

1. Check whether the power supply of the display screen is normal, if the power supply is not normal, please replace the power supply module.

2. Check whether the cable contact is good, and if there is a problem, replace the cable.

3. Check whether the display screen is damaged, replace the display screen test, if it returns to normal, the display screen is damaged. If it is the same, the power supply is normal, and the cable contact is good, check the output signal of the motherboard, and replace the motherboard for testing.

4. The problem of poor contact, if the car is ignited, it can be lit up normally, which means that the instantaneous current is large, so it is lit up, and then it is not lit. It seems that there is a problem with the *** poor contact or the circuit.

If the car display screen is not lit, you can unplug the battery wiring of the car after turning off the engine, discharge the control computer and re-drain the silver, and then reconnect the power to try.

If the instrument indicator light is not on, first check the vertical fuse of the power supply of the dashboard.

If the circuit breaker. will need to be replaced. Disassemble the dashboard, the lights are generally at the back of the dashboard, replace the lights that are not lit, and generally the individual lights are not lit to indicate that there is no problem with the fuse and wire, the main reasons are as follows

1. The lamp of the dashboard is damaged and needs to be replaced in time;

2. If the power supply line of the dashboard is broken, there will be an open circuit or a short circuit, which will also lead to the car dashboard.

There is no light up;

3. If the power supply fuse of the car dashboard is broken, there will naturally be no power supply, and the dashboard will not light up.

Precautions in the use of the car dashboard:

1. When the indicator light is on, the odometer should be observed immediately, if the cumulative mileage reaches or exceeds l00000000 front fiber staring km, the timing toothed belt must be replaced, otherwise the timing toothed belt may break, so that the engine can not work normally.

2. After replacing the new timing toothed belt, it is necessary to open the rubber plug outside the reset switch on the mileage dial, and press the reset switch inside with a small round bar to extinguish the indicator light of the timing toothed belt.

3. After replacing the new timing toothed belt, remove the odometer and adjust all the silver and readings on the odometer to the 0 position.

Line contact fault, it is recommended to troubleshoot, thank you.

How to use the Mercedes-Benz E300L ESP

The ESP function is intelligently controlled by the driving computer, which does not require manual control by the owner, and mainly maintains the stability of the vehicle when it is running at its limit. In the event of an imminent skidding or tail flick, the output torque is reduced and the power distribution is balanced. Harmony adopts unilateral wheel braking and other methods to effectively prevent accidents.

Therefore, in general, it is not recommended for car owners to manually turn off the function.

ESP can be temporarily disabled in the following cases:

1. The vehicle is stuck in a quagmire

The ESP system reduces engine torque, making it difficult to get out of the vehicle due to insufficient torque.

2. Drive to the limit

Actions such as bending and drifting of the drainage canal and ejection start require a certain slip rate to complete, and ESP cannot slip after intervention.

3. Snow-covered pavement

On snowy roads, tire friction decreases significantly. The ESP intervention will make the wheels less torque, and they will roll properly on snowy roads. However, be sure to turn on the ESP when the snow is just starting to melt.

4. Install snow chains on tires

The diameter of the tire changes, and the sensor detects an abnormality. The ESP will constantly warn you to play the tent, which will affect the driving.

Mercedes-Benz E300 turn off the ESP and follow the steps below:1. Operate the left and right arrows of the left function keys on the steering wheel.

The menu appears in the middle, press the OK key.

3.Start the engine according to the guide, press the OK button, and disable the ESP anti-slip function.

When the function is disabled, the meter ESPOFF indicator lights up. In this case, the ESP function is disabled.

When you want to re-enable the ESP feature, press OK again to enable it.

ESP is the abbreviation of Electronic Stability Program, that is, the electronic stability control system of the body, which generally includes ABS (anti-lock braking system) and ASR (traction control system), as well as the functional extension of these two systems.

Different manufacturers have different names for the electronic stability control system of the automobile body. For example, Honda is called VSA, and Toyota is also known as VSA.

In most cases, it is necessary to turn on the body stabilization system. It is only necessary to turn off the stability system in the following special cases.

1.Rafting time. You can't float without shutting down the ESP system.

2.Turn off the ESP system in snow, muddy potholes, and desert road tires slippage. 3.

If snow chains are installed, the ESP system also needs to be turned off, otherwise the snow chains will affect the signal of the wheel speed sensor, which in turn will affect the judgment of the ESP, which may lead to the continuous intervention of the ESP.

Millions of car parking subsidies.