Mercedes Benz GLK300 maintenance light to zero?

The maintenance lamp is reset to zero as follows:

Method] 1. Turn on the ignition switch to the ON gear, press the "OK" button on the left side of the steering wheel and hold, while holding the "Answer" or "Hang Up" button on the right side for nearly 5s

2. Select "ASSYST Plus Workshop" from the multi-function display on the dashboard, and press the "OK" button to confirm, 3. Press the "forward" or "backward" button to select "Service Done" and then press the "OK" button, if you want to add terms outside the current service scope, you can press the "forward" or "backward" button to select "further service".

4. After performing the above operations, press the "forward" or "backward" button to select "full service", or "then press the "ok" button, 5. press the "back" button on the left side of the steering wheel to return to the main menu and turn off the ignition.

The zeroing method is as follows.

Turn on the ignition to the ON position, press the "OK" button on the left side of the steering wheel and hold, while holding the "Answer" or "Hang Up" button on the right side for almost 5s.

Select "ASSYST Plus Workshop" from the multifunction display on the instrument panel and press "OK" to confirm.

Press the "Forward" or "Backward" button, select "Service Done", and then press the "OK" button.

Press the "Forward" or "Backward" button to select "Service Due", and then press the "OK" button to confirm. If you want to add terms that are outside the scope of the current service, you can press the "forward" or "backward" button and select "further service".

When you are done with the above, press the Forward or Backward button to select Full Service or then press the OK button.

Press the "Back" button on the left side of the steering wheel to return to the main menu and turn off the ignition.

Hello, Mercedes-Benz GLK300 maintenance light will be reset to zero.

There are many ways to zero the Mercedes-Benz GLK300 maintenance light, which are roughly the following six:

1. Turn on the ignition to the ON gear, press the "OK" button on the left side of the steering wheel and hold, while holding the "Answer" or "Hang Up" button on the right side for nearly 5s

2. Select "ASSYST Plus Workshop" from the multi-function display on the dashboard and press the "OK" button to confirm, 3. Press the "forward" or "backward" button to select "Service Done" and then press the "OK" button, 4. Press the "forward" or "backward" button to select "Service Due", and then press the "OK" button to confirm. If you want to add terms outside the current service scope, you can press the "forward" or "backward" button to select "further service", 5. After performing the above operations, press the "forward" or "backward" button to select "full service", or "then press the "ok" button, 6. press the "back" button on the left side of the steering wheel to return to the main menu and turn off the ignition.

Start the car, then press the button on the left side of the dashboard twice to turn off the engine, the button is not put, then ignite the car, wait a few seconds and you will hear the B sound, then release the button.

The free-range light reminds the owner that the new maintenance time has arrived, and it is recommended to maintain it in time. Some models can only be operated through the special computer of the car series, and the maintenance lights cannot be reset to zero manually.

Features of the Mercedes Benz GLC200:

Mercedes-Benz GLC200 does not have any advantage in **, and several other SUVs are better than Mercedes-Benz GLC200 in terms of terminal discounts. In terms of configuration, the GLC200 does not lag behind them, and can only be described as equal.

In addition, the GLC200 and Audi Q5 are among the models that use full-time four-wheel drive, which has a certain improvement in handling. However, the disadvantage of GLC200 is power, and all four SUVs use turbocharged engines, which are inferior to several others in terms of engine parameters.

**Mercedes-Benz C, E, GLK and other stuffy models (W204 W211) maintenance lights are reset to zero, follow the steps below:

1. Mercedes-Benz C, E, GLK, CLS and other models can be operated by the button on the left side of the steering wheel and call up the menu of the instrument information center. Friendliness.

Through the operation of the left and right buttons of the steering wheel, the menu of the instrument information center is brought up.

Use the left and right buttons to go to the (Maintenance) menu.

Adjust to (assyst) by pressing the up and down keys

plus) and press OK.

5. The dashboard will display the number of kilometers left from the next maintenance.

One, manual zeroing:

1. Press down and hold the zero button "A" while pressing the brake.

2. The ignition switch is twisted to "on", do not start.

3. The character "INSP" will flash or the display will flash.

4. Continue to hold down the zero button "A" until "....appears on the display.

5. Release the zero button "A" and release the brake.

6. The ignition switch is twisted back to the quiet gear vertical "off" state. The zeroing work is over.

Second, enter the settings menu, vehicle menu, select oil life, and reset to zero.

Third, use the car computer to detect the stupid instrument to zero the maintenance lamp. Kaida.

1. First of all, turn the key of the car to the 1st gear and adjust the Mercedes-Benz SLK200 instrument to the total mileage page, as shown in the figure below.

2. Then you need to press and hold the ** button and OK button on the steering wheel, and after 3 seconds, the Mercedes-Benz SLK200 instrument will appear in the selection menu, as shown in the figure below.

3. Next, select the ASSYST PLUS option on the Mercedes-Benz SLK200 display, press the "OK" button on the steering wheel, and select "Complete Maintenance", as shown in the figure below.

5. Finally, turn off the Mercedes-Benz SLK200 vehicle key and then turn it back on, so that the Mercedes-Benz SLK200 vehicle maintenance light will be zero.

Mercedes-Benz SLK200 oil lamp zeroing method:

Enter the key, twist a grid, press the ** answer button, and press the OK button within 1 second, for about 5 seconds, the assistplus interface will pop up, and you can select the maintenance according to the prompts.

Oil lamp: 1) Only the normal oil pressure can ensure that the oil is delivered to all the friction parts of the engine, too high or too low will affect the normal operation of the engine, and even cause damage to the engine parts. Therefore, when the oil lamp alarms, it should be stopped immediately to find the cause, and the work can be continued only after the fault is eliminated.

2) The following reasons may make the oil lamp alarm:

1. The oil volume of the engine oil is insufficient, so that the oil volume of the oil pump is reduced or the pump cannot be oiled due to air intake, resulting in the oil pressure dropping;

2. The engine temperature is too high, which is easy to thin the oil, and a large amount of oil pressure is lost from the mating gap, resulting in a drop in oil pressure;

3. When the oil pump parts are damaged or the gap is too large due to wear and assembly, it will cause the failure of the oil pump not producing oil or insufficient oil output;

4. The matching gap between the crankshaft and the large and small tiles is improper, too tight will increase the oil pressure, and too loose will reduce the oil pressure;

5. The blockage of the oil filter and suction plate will also reduce the oil pressure;

6. Damage or failure of the oil return valve: if the spring fatigue of the oil return valve of the main oil channel is softened or adjusted improperly, and the mating surface of the valve seat and the steel ball is worn or stuck by dirt and closed tightly, the oil return volume will increase significantly, and the oil pressure of the main oil channel will also decrease;

7. Improper selection of engine oil: if the wrong use or improper selection of the brand, the leakage will be increased due to the low viscosity of the engine oil when the engine is running, so that the oil pressure will be reduced;

8. There is oil leakage and blockage in the oil pipeline.

The car maintenance light zero method.

One. Use the car computer detector to zero the maintenance lamp.

Two. Manual zeroing by method:

1. Press down and hold the zero button "A" and press the brake at the same time.

2. The ignition switch is twisted to "on", do not start the car.

3. The character "INSP" will flash or the display will flash.

4. Continue to hold down the zero button "A" until "....appears on the display.

5. Release the zero button "A" and release the brake.

6. The ignition switch is twisted back to the "off" state. The zeroing work is over.

Three. Go to the settings menu, the vehicle menu, select Oil Life, Reset to Zero.

If you can't do it yourself, you have to send Mercedes-Benz for special maintenance, and use their terminals through electronic sockets.

You have to use a computer. You can find a repair shop.

But I'm sorry, I can't really say that.

If you want to use x431, you can, but this is very troublesome, such a good car or find a professional one, it doesn't cost a few dollars, and it can't be broken if it is broken.

Mercedes-Benz SLK200 maintenance light is a fixed number of kilometers to prompt the driver to carry out maintenance, that is, to replace the car engine.

After the maintenance of the engine oil, it needs to be clear by manual means, that is, to reset the calculated mileage of the maintenance lamp to zero, and the specific operation steps are as follows:

1. Press and hold the maintenance elimination shortcut key of the Mercedes-Benz SLK200 dial.

Do not let go. <>

2. Press the driver's brake pedal of the Benz Danchi SLK200.

3. Rotate the key of the Mercedes-Benz SLK200 to the ON gear.

4. When the instrument of Mercedes-Benz SLK200 lights up, release the maintenance elimination shortcut key.

5. Press the OK button of the Mercedes-Benz SLK200 multi-function steering wheel to confirm the elimination.

1. Mercedes-Benz R300 maintenance light zeroing can be operated by the left and right buttons of the steering wheel to call up the instrument information center menu, which is on the steering wheel.

2. Adjust to the maintenance menu through the left and right buttons, and you can see the information of the left and right buttons on the dashboard.

3. Adjust to (assyst plus) by pressing the up and down buttons, and then press the "OK" button, and you can see the relevant spring maintenance information by slowly staring at the resistance.

4. The car dashboard will display the remaining kilometers from the current to the next maintenance, please take a picture to maintain it in time.