Mercedes Benz E300L maintenance with a few liters of engine oil

The amount of oil added to change is about 8L, and you can look at the amount of oil after adding oil.

To remind you how to check the oil, start the vehicle after adding the oil, turn off the engine for 3 minutes after the meeting. Because the oil filter needs to be changed at the same time as the oil is changed, there is no oil inside the new oil filter, and the oil will flow into the oil filter after starting the vehicle. Turn off the engine for 3 minutes so that the oil can flow into the oil pan.

It would be more standard to look at the oil this way. Remember not to check the oil level on the ramp, because the vehicle is tilted, and the oil is also inclined in the oil pan, so the oil level is not standard. The drawn dipstick must be viewed perpendicular to the ground.

This is the most accurate view.

Adding too much oil will affect the normal operation of the crankshaft. It will also lead to an increase in the fuel consumption of the vehicle, which is not allowed: when the crankshaft journal runs to the bottom dead center, it will hit the oil and produce resistance, which affects the normal operation and is not allowed.

If there is less oil, it will not be used for circulating lubrication, which will lead to accelerated wear and tear of internal parts of the engine and damage to the engine.

The Mercedes recommendation is 6-7 liters of oil. My car is imported G T magic red engine oil, the engine sound is very quiet, the oil is quiet, because it is an additive of liquid molybdenum, the anti-wear protection ability is very good, can reduce the friction of the engine, reduce the noise of the engine. I feel a lot better driving now than I did when I used other oils.

1.Oil Generally speaking, oil consumption is not severe enough to get through the cycle between maintenances, but in the summer due to the hot weather, oil consumption will be a little higher than usual. If it is found that there are impurities or gasoline smell in the engine oil during the daily inspection, and the exhaust smoke is light blue, it means that there is a problem with the engine, and the parts may be abnormally worn, so you should enter the factory for maintenance as soon as possible.

2 Transmission oil.

When you change your engine oil, you can check your transmission oil by the way, and since the inspection process is more cumbersome, you can ask the dealer's service department to handle it. In order to measure accurately, the car must be discharged into neutral p, run at idle speed, and parked on a flat place, and the oil must run to an operating temperature of 80 93.

3.Too much or too little oil can damage the gearbox, and too much oil may cause excessive resistance to the operation of the parts, or cause the transmission oil to bubble and deteriorate, resulting in abnormal wear and tear of the parts. So when you check your transmission fluid, it's important to measure accurately.

4.Power steering oil.

When the engine cools down, wipe the top of the oil filler cap and the oil reservoir clean, then unscrew out the direction oil cap, and wipe the dipstick clean with a fiber-free clean paper towel, and then install the lock, and then open and pull out the oil level to check the dipstick.

To fill or change the oil, it is necessary to use the correct power steering oil, if it is not used properly, it will cause damage to the steering machine.

5.Brake fluid.

Just open the hood and look at the level of the brake oil can, as long as it is not lower than the lower limit.

When the level of brake fluid is not checked, brake fluid should not be added, so as not to add too much, and the brake oil will be sprayed to the high-temperature engine, resulting in corrosion and even combustion. If there are bubbles in the brake oil, or the oil becomes dirty, it means that the brake fluid has deteriorated, please replace it as soon as possible to avoid the brake oil boiling point from decreasing and causing bubbles, resulting in poor braking effect.

I need about 7 liters of engine oil for a Mercedes-Benz C200 maintenance, and I don't need to fill it too full, so that the liquid level can be kept in the middle of the oil dipstick line. Every time I choose to buy G T Magic Red engine oil, a base oil of Class IV PAO, the quality is very good, the anti-recession ability is strong, the maintenance cycle is long, and it is much easier to use than the original factory.

I bought my own G T magic red, gla is 6L every time, don't fill up, to the middle of the fuel gauge can be, you can run about 15,000 kilometers at a time, and you only need to change the oil once a year, which is economical and affordable.

Hello! Your one should be a 272 6-cylinder engine in standard liters! [Car questions, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

Hello, the most standard is seven liters [car questions, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Mercedes-Benz E300L to check the oil level, you can use the engine's oil dipstick to check, that is, you can check it by pulling out the oil dipstickThe specific steps are as follows:

1. Open the car attack backup door on the side of the cab.

2. Pull the hood switch on the left side of the driver's leg. Pat Kai <>

3. Lift the hood of the engine upwards.

Fourth, pull out the dipstick in the figure.

Fifth, the picture is the appropriate position.

Precautions: 1. The oil dipstick should be wiped clean and inserted again to be accurate.

2. Don't be motivated.

This model does not have a normal oil scale, the fuel level is displayed on the dashboard. After maintenance, look at the dashboard display.

The amount of oil should be controlled between the upper and lower scale marks of the dipstick. Because too much lubricating oil will enter the combustion chamber from the gap between the cylinder and the piston, and burn to form carbon deposits.

These deposits can increase the compression ratio of the engine and increase the tendency to detonation; The red-hot state of carbon deposits in the cylinder is also easy to cause premature ignition, such as falling into the cylinder will aggravate the wear of the cylinder and piston, and will also accelerate the pollution of lubricating oil. Secondly, too much lubricating oil increases the stirring resistance of the crankshaft connecting rod, which increases fuel consumption.

Mercedes-Benz E300L to check the oil level, you can use the engine's oil dipstick to check, that is, you can check it by pulling out the oil dipstickThe specific steps are as follows:

1. Open the door on this side of the cab.

2. Pull the hood switch on the left side of the driver's leg.

3. Lift the hood of the engine upwards.

Fourth, pull out the dipstick in the figure.

Fifth, the picture is the appropriate position.

Precautions: 1. The oil dipstick should be wiped clean and inserted again to be accurate.

2. Don't be motivated.

Mercedes-Benz E300L can see the amount of oil directly by looking at the oil dipstick on the instrument, and the red oil dipstick pointer indicates that the oil is insufficient and needs to be added.

The Mercedes-Benz E300L is an exclusive car designed for the Chinese market, and its extended wheelbase is entirely designed to meet the needs of domestic users, and it will offer a more competitive price than the imported version when it is made in China.

This model does not have a normal oil scale, its fuel level is displayed on the dashboard. After maintenance, look at the dashboard display.

This model does not have a normal oil scale, and the fuel level is displayed on the dashboard. After maintenance, look at the dashboard display.

The amount of oil should be controlled between the upper and lower scale marks of the dipstick. Because there is too much lubricating oil, it will enter the combustion chamber from the gap between the cylinder and the live burial plug and burn to form carbon deposits.

These deposits increase the engine compression ratio.

Increased propensity to produce detonation; The red-hot state of carbon deposits in the cylinder is also easy to cause premature ignition, such as falling into the cylinder will aggravate the wear of the cylinder and piston, and will also accelerate the pollution of lubricating oil. Secondly, too much lubricating oil increases the crankshaft.

The stirring resistance of the connecting rod increases the fuel consumption.

The amount of oil added to replace is about 8L, and you can look at the amount of oil after adding the envy engine oil.

According to the viscosity division 10W-40 is its SAE standard viscosity value, this viscosity value first indicates that the oil is a multi-grade engine oil, W stands for winter, the number in front of W represents the flow performance at low temperature, the more the value is small, the better the starting performance at low temperature. The number after w represents the stability of the oil at high temperatures, and the higher the value, the better the stability of the oil at high temperatures.

Main Effects:

The engine is the heart of the car, and there are many metal surfaces in the engine that rub against each other, and these parts move fast, the environment is poor, and the operating temperature can reach 400 to 600 meters. Under such harsh working conditions, only qualified lubricating oil can reduce the wear of engine parts.

1. Lubrication: between the piston and the side cylinder, the spindle and the bearing.

There is a fast relative slip between them, and to prevent the parts from wearing out too quickly, an oil film needs to be created between the two sliding surfaces. An oil film of sufficient thickness separates the surface of the relatively sliding part to reduce wear.

2. Auxiliary cooling and cooling: the specific calorific value of the engine oil.

lower, and inside the engine, it does not have a cooling effect on its own. However, due to the heat generated by fuel combustion in the engine, when the engine is working, the oil can bring the heat back to the oil tank and then dissipate it into the air to help the water tank cool the engine, and the real cooling effect is the water (or antifreeze liquid) outside the engine case.

The above content reference: Encyclopedia - engine oil.

Mercedes-Benz E300 displacement maintenance needs to add about eight liters of engine oil.

Mercedes-Benz E300 displacement car oil should not be too little, but also should not be added too full, the next understanding of how much car oil to add as a standard: by observing the oil dipstick to measure, the oil stains should be between the upper and lower lines of the dipstick, the center line is up. Each model has a different capacity, so the number of liters of oil added is different.

The red-hot state of carbon deposits in the cylinder is also easy to cause premature ignition, such as falling into the cylinder will aggravate the wear of the cylinder and piston, and will also accelerate the pollution of lubricating oil. Secondly, too much lubricating oil increases the crankshaft.

The stirring resistance of the connecting rod increases the fuel consumption.

When carrying out maintenance, how many liters of oil is added at a time depends on the type of engine, generally small displacement vehicles need to add oil liters for each maintenance, and large displacement needs to be about liters.

1.Engine oil: changing the engine oil is the most common item in maintenance, the oil is to play the role of engine lubrication, reducing the temperature of the tung hand, damping and buffering and reducing wear, etc., the oil has a life cycle, so it should be replaced regularly, different types of oil replacement cycles are not the same, and the current oil types are divided into three types:

Fully synthetic, semi-synthetic and mineral oils. Fully synthetic motor oils have better high and low temperature types, and ** are also the highest of the three. The replacement cycle is generally 10,000-12,000 kilometers.

The replacement interval of semi-synthetic engine oil is 8,000-10,000 km. Mineral oil is generally replaced at 5,000 km.

2.Three filters: Three filters refer to the oil filter element and the air filter element.

and cabin air filters. The function of the oil filter is to remove various impurities in the oil and ensure the normal lubrication system, so the oil filter should be replaced together with the oil when changing the oil. The air filter element is used to filter the air to ensure the cleanliness of the intake air, and the replacement cycle is 20,000 kilometers or 2 years.

The air conditioning filter is to prevent dust and odor from entering the car, and the replacement cycle is 20,000 kilometers or 2 years.

3.Spark plug.

The function of the spark plug is to ignite the high combustible gas mixture in the cylinder, once the working time is too long, it will make the engine run unevenly and produce shaking, and even form a lack of cylinder, which can not ignite, and at the same time will make the engine more fuel-efficient, so the role of the spark plug is very important. The replacement cycle of iridium fire plug is 80,000-100,000 km, the replacement cycle of platinum spark plug is 50,000-60,000 km, and the replacement cycle of nickel-gold spark plug is 20,000-30,000 km.

4.Gearbox oil: Gearbox oil is the gearbox, and the role is to play a lubricating role. There is an automatic transmission.

oil and manual transmission.

There are two types of oil. The automatic transmission replacement cycle is about 80,000 km, and the manual transmission replacement cycle is about 120,000 km.

5.Coolant.

The coolant is to ensure the normal operation of the water-cooled engine, and if it is not replaced for a long time, the coolant performance will deteriorate, resulting in the engine temperature being too high or too low. The replacement period is 60,000 km or 4 years.