How to adjust the electronic pricing scale, how to adjust the price of the electronic scale

1. Before commissioning, you must turn on the power switch to warm up for 15 minutes, and try to use a vehicle with a load capacity close to the maximum capacity, pass back and forth many times and brake on the load-bearing platform to stop, and tighten the high-strength bolts of each load cell with a torque wrench.

2. Use a digital voltmeter to measure the output voltage of each load cell in turn, if there is any inconsistency, you can adjust the corresponding two precision adjustable resistors in the junction box respectively to reduce the difference between them. However, it must be noted that the rotation direction of the two adjustable resistors should be the same, and the rotation amount should also be the same, and the resistance decreases when rotating clockwise, the output voltage becomes larger, and the display value increases, otherwise vice versa. until the output of each load cell is consistent.

3. Debugging can generally be carried out by gravimetric method, that is, the weight of 1 10 maximum weighing capacity is put on the load-bearing platform center position and the load-bearing platform above each load cell in turn, and the difference of the output of each load cell is accurately measured by the real difference method, and the two precision adjustable resistors corresponding to the load cell of each bearing point are adjusted respectively at the same time, so as to reduce the difference between each other, but the direction of rotation and the amount of rotation are the same.

4. After the bearing point is debugged, the weight equivalent to the maximum weighing capacity is evenly added to the load-bearing platform, and the display value is consistent with the weight value according to the position and method introduced in the instructions of various weighing displays, and the weight is removed and the empty scale is displayed as "0". Finally, the maximum weighing capacity is divided into several parts, which must include the minimum weighing capacity, the maximum weighing capacity and each weighing point of the tolerance change, and the weighing error of each point is required not to be greater than the maximum tolerance requirement of each measurement point.

Dear, there are detailed records in the general electronic scale manual, and you can also directly contact the manufacturer's after-sales or technical contact to further determine the method of fine-tuning. Zhengzhou electronic scale expert Jinmai weighing instrument will answer for you.

Didn't you have an instruction manual when you bought it?

Summary. 1. The first thing is to start the electronic scale. 2. Then press the save button.

3. The unit price in the middle will be displayed as shown in the figure below. 4. At this time, enter the unit price of your product. 5. Finally, click to store the unit price into the unit price (such as pressing "Unit Price 1", this unit price will be stored in "Unit Price 1") 6. Turn off the electronic scale, restart this setting is still valid, just press a button to complete the unit price input.

Hello, I have seen your question and am sorting out the answer, please wait a while Hello. 1. The first thing is to start the electronic scale. 2. Then press the save button.

3. The unit price in the middle will be displayed as shown in the figure below. 4. At this time, enter the unit price of your product. 5. Finally, press to store this unit price in that unit price (such as pressing the "unit price 1" of the land trace, and this unit price will be stored in the "unit price 1") 6. Turn off the electronic scale, restart the Dan Xi Pai setting is still valid, just press a button to complete the unit price input.

As long as the price of the kilogram is entered, it will be slippery, OK, you can set a few prices, such as the unit price 1, the single boring price 2, etc., as long as the first input is followed by the corresponding price.

One is counted at 3 yuan, and the other is the same as the money below.

I still don't understand, it's a bit of a circle.

Try it more and you'll find out.

3. All electronic scale debugging methods:

1. After booting back to zero, enter and press the "Tare" button.

Second, enter or press the "Peel" button again.

3. After waiting for a few seconds, add 1 3 weights, and then press the "Peel" button.

4. Enter the weight value of the weight. Press the "Peel" button again.

5. Enter the weight value of the full scale, and then press the "Tare Down" button.

6. Enter the graduation value, and then press the "Peel" button.

7. The electronic scale returns to the weighing state, that is, the debugging is completed.

Electronic scales are a type of scale, a tool that uses Hooke's law or the lever balance principle of force to determine the mass of an object. The electronic scale is mainly composed of three parts: load-bearing system (such as weighing pan, weighing body), force transmission system (such as lever force transmission system, sensor) and value indication system (such as dial and electronic display instrument). According to the structural principle, it can be divided into three categories: mechanical scales, electronic scales, and electromechanical scales.

1. Press and hold the decimal point button for a few seconds, and release it when "centr" appears.

2. Then press the "8" button.

3. The weight column shows d1.

4. At this time, the number of decimal places is displayed, and the default factory value is displayed.

5. The weight value will appear at this time. After entering, press the "Accumulation" button to proceed to the next step.

6. At this time, LCP will appear in the weight column and OFF will appear in the single weight column.

7. Cal appears in the weight column, 0 appears in the single weight column, and weight value appears in the total column.

8. When the weight of the weight column jumps and the weight appears, it means that the correction is completed.

Electronic scale debugging method:

After turning on the computer back to zero, enter and press the "Tare" button. Second, enter or press the "Peel" button again. 3. After waiting for a few seconds, add 1 3 weights, and then press the "Peel" button.

4. Enter the weight value of the weight. Press the "Peel" button again. 5. Enter the weight value of the full scale, and then press the "Tare Down" button.

6. Enter the graduation value, and then press the "Peel" button. 7. The electronic scale returns to the weighing state, that is, the debugging is completed.

Manual, if not, find a professional maintenance, pricing scale brands are many, passwords are also very miscellaneous, miscellaneous cards are very difficult to correct.

If you are looking for a professional maintenance scale, use standard weights, and have a calibration method.

Calibrate with standard weights according to the instructions.

Recalibrate the scales with standard weights!

The steps to set the unit price and amount on the scale are as follows:

1. First of all, it is necessary to open the electronic scale, and the dust switch is generally in the back or lower right corner, which is different for different models.

2. Then there is a row of unit price 1 below, unit price 2 all the way to unit price 8, press unit price 1.

3. Then press Save, and a small circle will appear in the unit price column.

4. Then press the unit price of your own product, pay attention to the fact that this is per kilogram, and if you want to sell a pound of money, you need to press twice the value of him.

5. Finally, put the product corresponding to the stuffy Zen, and the amount in the last column is to show how much the product can be worth.

The precautions for using electronic scales are as follows:

It is strictly forbidden to rain or rinse with water, if it is accidentally wet, wipe it with a dry cloth, and send it for repair as soon as possible when the machine is not functioning properly.

It is strictly forbidden to knock on and press hard.

Do not place in high temperature and humid environment (except for special waterproof and anti-corrosion scales). Do not allow cockroaches or small creatures to enter the machine to avoid damage.

If the electronic scale is not used for a long time, the machine must be wiped clean, put in the desiccant and wrapped in a plastic bag, and the dry battery should be taken out. When using rechargeable batteries, they should be charged every three months to ensure their longevity. Charging should not exceed 8 to 10 hours. <>

The method of adjusting the unit price of the electronic pricing scale:

1. Start the electronic scale first;

2. Press the storage button;

3. The unit price in the middle of the display screen is displayed as half of the 8;

4. Press the number button to enter the unit price of the commodity;

5. Store this unit price in the price of a disrupted list to slowly change the file, such as pressing "Unit Price 1", this unit price will be stored in "Unit Price 1";

6. Restart the electronic scale and press a button to complete the input of the unit price.

Turn on the electronic scale, the switch is on the back or in the lower right corner. 02 There is a row of unit price 1 below, unit price 2 all the way to unit price 8, press the unit price and press it"Storage", a small circle will appear in the unit price column. 04 Press the unit price of your own products, pay attention to the unit is per kilogram, how much is generally sold per catty, you need to press twice its value.

05 Finally, put the corresponding product, and the amount in the last column is to show how much the product is worth.

Summary. How to set the unit price and amount: 1. First, in the setting interface of the electronic bang, find the "**Settings" option and click to enter; 2. In the ** setting interface, you can see the two options of "Unit Price" and "Amount", click "Unit Price", and enter the unit price you want to set; 3. Then, click "Amount" and enter the amount you want to set; 4. Finally, click the "OK" button to complete the setting of unit price and amount.

How to set the unit price and amount: 1. First of all, in the setting interface of the electronic bang, find the "**Setting" option and click to enter; 2. In the ** setting interface, you can see the two options of "Unit Price" and "Amount", click "Unit Price", and enter the unit price you want to set; 3. After the trip, click "Amount" and enter the amount you want to set; 4. Finally, click the "OK" button to complete the setting of the price and amount of single pruning.

I'm still a little confused, can you be more detailed?

How to set the unit price and amount: 1. First, in the setting interface of the electronic bang, find the setting options of "unit price" and "amount", and then enter the corresponding value; 2. Then, click the "OK" button to complete the setting of the unit price and the amount of good balance; 3. Finally, click the "Save" button to destroy it, and you can save the unit price and amount set by Yousold. Causes of the problem:

1. When the user sets the unit price and amount, there may be input errors; 2. When setting the unit price and amount, the user may forget to click the "OK" button, resulting in the invalid unit price and amount set; 3. When setting the unit price and amount, the user may forget to click the "Save" button, resulting in the set unit price and amount cannot be saved. Solution: 1. When setting the unit price and amount, the input value should be carefully checked to avoid input errors; 2. When setting the unit price and amount, be sure to click the "OK" button to ensure that the set unit price and amount are valid; 3. When setting the unit price and amount, be sure to click the "Save" button to ensure that the set unit price and amount can be saved.

Personal tip: When setting the unit price and amount, be sure to double-check the values entered, and remember to click the "OK" and "Save" buttons to ensure that the unit price and amount you set are valid and can be saved.