What should I do if I forget my wireless router password?

For most routers, if you forget the username and password of the router background management, you will not be able to enter the router. At this time, the router can only be reset and restored to the factory state. However, for dlink, you can use the default ordinary account to log in to view the settings.

At the same time, due to the different reset methods of different brands and models of routers, they are roughly the same and have some commonalities, so a comprehensive method is used here to solve the problem.

1.Unplug all network cables from the router and keep only the power cable.

2. Then use a slightly sharper pen tip to prick the "reset" hole on the back of the router. Some of them are "reset" buttons, and they are also holding down this "reset".

3.Disconnect the power of the router again, and remember to hold down the reset button or the reset hole. Because some routers need to be reset when the power is turned on, we also plug in the router power in this comprehensive method.

4.Plug it back on, and all the lights on the front panel of the router will flash rapidly.

5.Keep the power on and turn on the power for about 5 seconds (some can take 10s), and the indicator will return to normal flashing. At this point, release and hold the reset key to restore the router configuration to factory defaults.

6.Then we use the network cable to connect to the computer, and the other end of the network cable is connected to any of the LAN ports on the router (usually marked in yellow), but do not connect the WAN ports first; Or connect the router SSID wirelessly.

7.Then if the computer can get the IP, then the router reset is successful. Then we should be able to enter the router background management IP through IE (such as entering the router.

1. Take a look at the router password of your router's brand (most of the Internet has different passwords for different brands) 2. Find the box where you installed the router, and there is a tutorial with the password of your router written on it.

3. Behind the router is the connector side, there is a small hole or a small button, this is the reset key, restore the default settings, but at the same time clear your Internet password on the router, (if you don't know how to set the WAN window settings, it is not recommended to do this).

There are only these 3 ways.

It's very simple: 1. Plug in the computer with the Internet cable, and enter it in IE.

2. If the user name and password are not changed, it will be written on the oil leaker manual. admin/admin

3. Enter the oil leaker settings and find the wireless network settings to see the password.

If you don't know, the special office is asking me.

Dial number 10000 and there will be a voice prompt.

Then manual service.

As long as you remember the account number.

The password will be told to you!

If you forgot.

You can buy a new router and plug it in, and enter it to set it up.

Hope it helps. Hope. Thank you!

1 In general, in.

Router. There will be a reset key at the back,Press and hold it for 3 seconds,You can restore the factory configuration,The password is admin,You can try 1 time。

1. If the password of the router is forgotten, then in addition to trying the default password, you can only reset the router and then reset the password, the router reset method is as follows:

Turn the wireless router over and see if there is a piece of paper as shown in the picture. If you haven't tried this password before, then enter this and password to see if you can log in.

If none of the above methods can log in to the management interface of the wireless router, then you can only restore the wireless router to factory settings. The sum password after the factory reset is the factory set and password, which is the words prompted by the label on the wireless router as shown in the picture above.

Find a round hole on the front or back panel of the router that is labeled Reset, which is the reset key for the router to factory reset. In the power-on state, press the reset button with a pointed object for 5 seconds, and then you will see the sys indicator in the front row of the router change from a slow flashing state to a fast flashing state, then release the reset button, and then you can restore the factory settings.

In fact, factory reset is very simple, use a pointed object to insert into the router reset hole, it is recommended that you use a ballpoint pen tip, or a thin and hard wire and toothpick. After resetting the factory settings, you can log in to the router with the default router login username and password, which is generally the label and password written on the router, that is, admin, and the password admin.

2. If you forget the password of WiFi, you can refer to the following two methods.

Method 1: If you have used your laptop to connect to the router, the computer will remember the password, and it will automatically connect next time, click on the wireless network signal at the bottom right.

Click on the linked network and right-click on the properties.

Click on the display character, which is the password for the wireless network.

Or use the computer to modify the wireless password, enter any browser casually, enter the IP address of the router in the address bar, you can look at the number at the bottom of the router, generally at the beginning, enter it into the address bar of the browser, press enter and the interface of setting up the router appears.

1. If the management page address of your router is, we need to modify the IP of the local connection. Open the network settings page and click Change adapter settings here.

2. Open this page, right-click the local connection, and then click Properties on the menu.

3. Click on the IPv4 option here and click the Properties button below.

4. Here you can set to automatically get the IP, or the IP address entered should be consistent with the IP segment of the router, for example, you want to change the third segment here.

5. After modifying and saving, enter the IP address of the router on the browser to open the management page, and enter the password to enter.

6. After entering the router, click System Management on the left navigation.

7. Come to this page, find the password setting item, enter a new password, and click the save button below.

Step 1: Open the browser of the computer connected to the current wireless router, enter part of the router in the address bar, check the bottom label of the router to know), log in to the web configuration interface of the current router, the username and password are admin by default Step 2: Under the network settings of the router, first find the WAN port setting option of the router.

The settings of different brands are actually similar, the most important thing is to turn on the DHCP function, so as to ensure that the router can assign an IP address to the device when it is connected to the LAN port or connected to WiFi, and the IP address range assigned by DHCP should be in the same network segment as the IP address of the router, such as Step 5: Finally, check the security settings of the router to see if some security policies that restrict MAC or IP address connections are enabled, or the corresponding rate limiting policy, If yes, turn it off, otherwise only devices with a specific MAC or IP address will be able to connect to check the phone settings

Step 1: Open the phone settings, select "Wi-Fi", and then, see the wifi signal that has been connected to the current one, click the blue circle arrow on the far right Step 2: Click "Ignore this network" Then, the wifi connection of the phone will be disconnected, so that the phone will not automatically connect when you click to connect the signal source again, but re-enter the connected wifi password, that is, the phone will re-identify the network once, In this way, the effect of clearing the original network configuration can be achievedStep 3:

If you want to empty it more thoroughly, you can open Settings --- General --- Restore in turn, and select "Reset Network Settings" so that the device will restart, after restarting, all previously connected networks will not be saved, but will be recognized as a new network, and you need to enter the wifi password to connect

If you forget the password of your wireless router, reset the router first, and press and hold the button next to the power cord of the router with a toothpick until all the indicators flash and then restart successfully. Log in to the webpage and search", fill in the username and password as admin, open the settings interface, select wireless security settings or scramble to see the password.

If you forget the password of the wireless router, the first thing to do is to reset the router of the group, there is a switch next to the power cord of the router, if you can't touch it directly with your hand, press it with a toothpick. Press with a toothpick for more than seven seconds, and see that all the indicators flashed and the reboot was successful, and then you can open the network settings of the computer.

After logging in to this wireless network, you will find that all the tabs have become admin, open ** and then enter ", then click the enter key to enter the server login window, enter the username and password. Since the router has been reset, both the password and the password are admin at this time, and press enter to enter the router login interface.

At this time, there are many options on the left side of the login screen, select "Wireless Security Settings" in "Wireless Settings", and a session box about the routing information will pop up. At this time, you can see the password of the router, if you need to change it, remember to click the "OK" button under the session box after the change.

Here's how to change the router's wireless password from your phone:

1. The mobile phone first needs to be connected to the wireless signal of the router, after successful connection, open the browser of the mobile phone, then enter the management IP of the router, and then enter the management password of the router to log in to the background of the router.

Open the IE browser, enter in the IE address bar, and then press Enter, a small login page with username and password will come out, the initial username and password are admin, after entering, click "OK" to enter the router settings interface.

There is a "Quick Settings" in the menu bar on the left side of the router settings interface, such as "Setup Wizard"), click on it, and then a page will come out to let you choose the Internet access method (if China Unicom or Telecom, choose PPPOE mode if you give the account password, if you give a set of IP addresses, select the static IP mode, and remember to fill in the local DNS when filling in the Internet broadband information).

Then click Next, you can see the account and password of the router, and then click Save. Restart the router (method: "System Tools" - "Restart Router" at the bottom of the router menu bar), and you can surf the Internet.

It is useless to restart the router, only to restore the router to factory settings and then reset the password.

When you faint, some people say that you crack it, and you hack it. There is only one way, factory reset and reset the password, but there is no way to restore the factory settings if you can't touch the router.

If your home computer is a note, it's very simple, and you can see the password there wirelessly. If it's a desktop, go for a wireless password viewer.

Log in to the router with a computer and see the connection password? Don't you even know the login password?

If you know how to connect to the Internet, reset it and reset it again.

Factory reset and reset the password.

What should I do if I forget my wireless router password? Don't worry! One simple step, pop up the password in an instant.

The router login password can be reset after the router is reset.