What should I do if the WLAN light of the wireless router does not turn on?

Wireless routers.

The WLAN indicator is not lit, and most of them are broadband modems.

**Poor contact between the cable and the network cable, or the external network that comes in.

There is a problem. You can try the following methods to solve it:

Replug the outside cable (usually the ** line) from the outside street, including the cat's power cord.

Then plug and unplug the network cable that comes out of the cat to connect to the wireless router, remember to plug and unplug both ends, one end is plugged into the cat, and the other end is plugged into the router, just see if it is plugged into the WLAN port of the router.

If the above operation does not work, try to power off the router and the cat for 5-10 minutes, and the two devices can take turns to power off, pay attention to check whether it is a device problem.

Finally, you can try to plug it directly into the computer without using a router and access the Internet through dial-up.

Try it, if it doesn't work, you can contact the broadband service provider to report for repair, it should be a problem with the external network line.

The WLAN light is an indicator that has been connected to the broadband modem, and it may not light up because it is connected to the cat or one end of the router is not connected properly, and the contact is poor, of course, other possibilities are not ruled out. For example, a router or a cat and its faults!

If the WLAN light is not on, the route and the cat may not be connected.

Check the network cable and the interfaces at both ends.

In fact, in the case of your friend, you can go and get an ADSL route. Connecting the cat and the router, the intermediate connection is prone to problems, and it also consumes power.

It may be that the wireless router has a faulty wireless network setup or that the wireless router system is faulty.

The steps are as follows:

1. Open the browser and enter the IP address of the router and press Enter;

2. Enter the router username and password, and click OK;

3. After entering the settings page, find the wireless settings - wireless basic settings, the option to turn on the wireless function has been checked, and then save;

4. You can restart the router to see if it has lit up;

5. If the setting is invalid, you can try to restore the default value of the router to see if it is restored.

Please add a detailed explanation.

Summary. If the wifi signal light suddenly doesn't turn on and you can't access the internet, most of it is due to the following reasons: Reason 1:

Problems with network cables. For example, poor contact, loose or tight network cables connected to the WAN port, and broadband arrears can all cause the WiFi signal light to go off and become unusable. Reason 2:

Router issues. Secondly, it can also be caused by a system failure or hardware failure of the router itself, and it is recommended to restore it to factory settings before using the router. Why is the wireless light of the router not lit because it is in arrears?

1.Wireless traffic lights have nothing to do with broadband, but with the router itself. As long as you add a little bit to the router and the wireless settings are good, it should be good.

Check whether you can search for wireless network signals and connect to your router through your wireless network. 2.If the broadband light is off, you can connect your home broadband line directly to your computer, set up a PPPoE virtual dial pad, and see if you can get a working IP address.

The router wifi light does not turn on.

Can you add, I don't quite understand it.

If the wifi signal light suddenly doesn't turn on and you can't access the Internet, most of them are caused by the following reasons: Reason 1: Network cable problem.

For example, poor contact, loose or tight network cables connected to the WAN port, and broadband arrears can all cause the WiFi signal light to go off and become unusable. Cause 2: Router issues.

Secondly, it can also be caused by a system failure or hardware failure of the router itself, and it is recommended to restore it to factory settings before using the router. Why is the wireless light of the router not lit because it is in arrears? 1.

Wireless traffic lights have nothing to do with broadband, but with the router itself. As long as you add a little bit to the router and the wireless settings are good, it should be good. Check whether you can search for wireless network signals and connect to your router through your wireless network.

2.If the broadband light is off, you can connect your home broadband line directly to your computer, set up a PPPoE virtual dial pad, and see if you can get a working IP address. If not, contact your broadband equipment provider to find out if it's an arrears or if there's a problem with your broadband access line.

If the wireless network is not set up, you can set it again.

When you don't use a router, your computer is directly connected to broadband Internet access, and now you need to use a router to connect to broadband directly. According to the different broadband lines in the home, it can be divided into three access modes: network cable, ** line, and optical fiber. After connecting the line, check that the corresponding interface indicator is solid or flashing.

Note: The broadband cable must be connected to the WAN port, the color of the WAN port is generally different from the LAN port, and the computer is connected to any port of 1 2 3 4.

Log in to your router.

1. Enter the router management address.

Open the Internet Explorer browser on the desktop of the computer, clear the address bar and enter the router management IP address, and the login box will pop up after entering.

2. Log in to the management interface.

When you enter the router management interface for the first time, in order to ensure the security of your device, you need to set a password for managing the router.

The setup wizard sets up Internet access.

1. Start the setup wizard.

Once you are in the management interface of your router, click on the Setup Wizard, and then click Next.

2. Choose a way to access the Internet.

Most routers support automatic detection of Internet access methods, and you can set the Internet access methods as prompted on the page. Select PPPoE (ADSL Virtual Dialing) as the Internet access method and click Next.

3. Enter the Internet broadband and password.

Enter the broadband and password provided by the carrier in the corresponding setting box, and make sure that the password is entered correctly.

4. Set wireless parameters.

The SSID is the name of the wireless network (can be set according to actual needs), select WPA-PSK WPA2-PSK and set the PSK wireless password, and click Next.

5. The setting is complete.

Click Done, and the setup wizard is complete.