How to set up router for ZTE F420 10

Home Network Environment Cabling]:

1. There is a telecom cat: the telecom cat --- router WAN port; The LAN port of the router --- a computer.

2. No telecom modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. Open the browser - enter the general router address is this or view the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

The IP and DNS settings of the computer are automatically obtained.

1. Enter the router.

Open the browser - enter the general router address is this or check the login information on the back of the router) enter the route - enter the user name, password, (the default is generally admin).

2. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the username and password for Internet access according to the prompts, and save.

3. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

If you want to install it for the first time, you can install it according to the setup wizard.

It should be noted that you need to put the password you connected with ADSL.

If you need to connect to Wi-Fi, remember to set the Wi-Fi password. There's nothing special about it.

1. First, click the wireless or wired icon in the lower right corner of the computer desktop, and then click it"Open the Network and Sharing Center"。

2. Then click "Wireless Network Connection" or "Local Network Connection".

3. Click "Details" in the pop-up page.

4. Then mark the red seepage cover where the router is the new IP address, and write down the IP address here.

5. Then enter the new IP address into the browser, and then enter the router and password to log in.

6. Finally, the router is logged in successfully, and the router can be set here, and the IP address is the same as the previous one.

How to set up wireless wifi on a wireless router:

1.The router is connected to the network, and the computer is wired to the wireless router.

2.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface.

3.Set the wifi name and password.

Go to Wireless Security in the wireless settings, select WPA2-PSK mode for security mode, and select AES for WPA encryption rule. After setting the wireless network key, the router will automatically restart, and the networked device will enter a new wifi password to connect.

The device is not a router, just a broadband modem or fiber optic modem, and does not need to be set up to use it directly; If you use dial-up to connect to the network, the network company will limit the number of end-device used, and the operation will be unstable; It is recommended to install a router, which is responsible for dialing, managing and sharing the use of wired and wireless networks; Feel free to ask!

1. The bus of the broadband network is connected to the WAN port of the router, and the LAN port of the router is connected to the computer.

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

ZTE ZTE F401 router setup wifi method: must be a wireless router.

How to set up wifi:

Turn on the router's wireless function].

1. Enter the router.

Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name, password, (the default is generally admin).

2. Select Wireless Settings --- Basic Settings.

3. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Enter the router.

Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name, password, (the default is generally admin).

2. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

ZTE router.

Here's how to set up a wireless router:

1. Enter the router address, connect the wireless router, enter the address you see on the router in the browser, generally of course, if your home is using ** online network, then you need to prepare an additional modem, commonly known as "cat").

2. Enter the corresponding account password, and after entering, you will see that you have entered the corresponding account and password.

3. Select the Setup Wizard, and then enter the operation interface, you will see a Setup Wizard on the left, and enter (generally pop up automatically).

4. Enter the Internet mode setting and set the interface of the wizard.

5. Click Next, enter the Internet access method settings, we can see that there are three Internet access options, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

I chose PPPoE because I dialed.

6. Enter the account password, select PPPOE dial-up Internet access to fill in the Internet account and password, this should be understood by everyone, there will be an account number to open broadband, fill it in OK.

7. Set the password of the router, and then enter the wireless settings after the next step, we can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill it in casually, and then the mode mostly uses 11BGNFor wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe that it will not be hacked and rubbed by the network.

8. The next step is to set it up successfully.

9. Click Done, the router will automatically restart, at this time you should wait patiently. The interface that appears after success.

10. How to connect the mobile phone to wifi is simpler, when your router is set up, click the menu key of the mobile phone, and then enter the mobile phone settings, the first item is wifi, and then you set it to on, click to enter the wifi list, and select the wireless network name set in your previous router. Enter the password you set earlier to connect.

Summary: How to use a wireless router, is a more common problem, but also a relatively simple problem, I believe that as long as you have an experience, you can also become a god, of course, the router settings are far from these simple content, there are more setting options after logging in to the router settings page, set other options, such as binding MAC address, over IP, firewall settings, etc., can make your wireless network more secure, to prevent being rubbed off the network.

This router is wired, and the router has no wireless capabilities.

Wireless Router Setup Bridging Steps:

1.Modify the IP address of the LAN port.

Set the LAN port addresses of the two wireless routers to different IP addresses of the same network segment, if the LAN port address of the higher-level wireless router is, you can set the LAN port IP address of the wireless router to the last value can be 2 254).

2.Set the SSID, encryption mode, wireless password, and channel of the two wireless routers to be the same.

3.Set up a higher-level wireless router.

1) Go to the wireless extension interface of the wireless settings, select WDS in the wireless extension mode, and click to start scanning.

2) Find the SSID of the wireless router in the pop-up dialog box, and then click to connect.

3) In the key, enter the wireless wifi password of this router.

4: Set up a lower-level wireless router.

1) Log in to the wireless router settings interface, refer to step 3, and add the upper wireless signal;

2) Disable the DHCP function of this wireless router.

5.After the setting is complete, check the IP address obtained by the computer, when the address of the "default gateway" is the IP address of the LAN port of the higher-level wireless router (in this case, the device can access the Internet.

In the settings interface of the router, find the wireless settings, then find the WPS bridging project, tick it, then fill in and then fill in the SSID name you want to bridge, enter the password, I hope you can adopt it.

You're a cat, not a router!

Kuankuantong is the authoritative broadband service of Sichuan Telecom, which is the best telecom speed measurement tool, the most convenient and fast telecom payment and recharge weapon, updated every day with the latest and most complete TV program previews, and TV program reviews, newly installed telecom broadband, and easy to master telecom TV. Click on the official **.

Discount**--- 100m broadband is free of charge.

Discount**--- 10m5 hours to speed up the monthly subscription.

Internet age acceleration, broadband acceleration, broadband speed test and other services ......

It's set up like a normal one.

ZTE ZXHN F412 Connecting to TPLink Router: Set Level 2 Routing.

1. How to connect two routers.

1. There is a cat (modem):

ZTE ZXHN F412WAN port; ZTE ZXHN F412LAN port--- TPLink router WAN port; The LAN port of the TPLink router --- a computer.

Second, the setting method.

Before setting, disconnect the WAN port network cable of the second router and plug it in after the setting is complete.

1. Set the IP segment of the TPLINK router.

After restarting the router, the address to enter the router is.

2. Set up the TPLink router to access the Internet.

Check the IP details of the computers connected under ZTE ZXHN F412. (win+r--input, cmd--input:ipconfig all [remember: ip, mask, gateway, dns]).

Set it on the TPLink router and select Static IP in the Setup Wizard. Enter the IP that the 1st router does not use, and the others: mask, gateway, DNS settings are the same.

Restart your router once it's set up.

Note that if you enable the routing function of the broadband modem, such as the dial-up function, the normal router settings will be invalid.

1. First, click the wireless or wired icon in the lower right corner of the computer desktop, and then click it"Open the Network and Sharing Center"。

2. Then click "Wi-Fi" or "Local Network Connection".

3. Click "Details" in the pop-up page.

4. Then the place marked in red is the new IP address of the router, and write down the IP address here.

5. Then enter the new IP address into the browser, and then enter the router account and password to log in.

6. Finally, the router is successfully logged in, and the router can be set here, and the IP address is the same as the previous one.

The default network segment of ZTE F420 is as long as you have not changed the management IP of ZTE F420, and the IP of the network segment is the same network segment.

You can set the routing address in the modem, but generally no one will do this, because there will be a conflict situation, and the modem will be connected to a router under normal circumstances. to configure external routes is more convenient and secure.

Suppose the IP address of your optical modem is, you modify the routing IP to the computer IP to; These three IPs are the same network segment, 1 segment, and you set the cat and the router IP to be the same, of course, there is a conflict.