Set up the secondary router, how to set up the secondary router

In this way, the router is used as a switch, the DHCP function of the secondary router should be turned off, and the computer address acquisition is assigned by the DHCP function of the first router.

If the network cable is unplugged, check whether the network cable connected by the superior can be used directly into the computer, and whether the network cable connected to the computer by the secondary router is good. If you are sure that there is no problem on the line, check whether the MAC address filtering function is enabled on the first-level router to prohibit connection. You can try the connection method of the network cable to the WAN port, but you need to change the LAN port address of the secondary router to avoid conflict with the DHCP assigned address of the higher-level router.

If the network cable is unplugged, then there is only one possibility, that is, the cable from your router to your computer is not properly connected or there is a problem with the cable itself, otherwise it will not show that the network cable is unplugged, but show the restricted connection.

Then, you use your router as a switch, in this case, you need to go to your own router settings interface, turn off the DHCP function of the router, and let the computer automatically obtain the IP address assigned by your neighbor's router, so that you can connect.

If there is no problem with the wiring, check whether the power indication of the router is on and whether the connection from the router to the computer is normal.

This is very simple, you: computer letter, the above method is very carefully taught, I hope it can help you.

There are two types of series connection between the router and the router, and the second router is used as a secondary route or as a switch wireless switch. Here's how to set up a Level 2 router, I hope it can help you!

How to set up a Level 2 router

Setup Instructions:

1) Define a route that directly connects to broadband as R1;

2) Define the routes that need to be connected in series into the current network as R2.

Connection method. LAN connection to WAN connection settings.

The specific steps are as follows:

1.Power on R2 and find a network cable from the computer to connect to R2. Any LAN port;

2.Open the browser on the computer, enter in the address bar, press enter to enter the router login interface;

3.Enter the default username and password in the login box to enter the management page of the router. Click Network Parameters, select LAN Port Settings, and change the default IP address to a network segment that is not in the same network segment as the R1 intranet (for example:

If the IP address of R1 is, then modify R2 to and click "Save and Restart".

4.After R2 restarts, find a network cable from any LAN port on R1 to connect to the WAN port on R2.

5 After the connection is completed, open the browser on the computer and enter, and follow the settings in step 2 to enter the management page of the router. Then click "Network Parameters" - "Public Network Configuration", select "Network Access Type" as "Dynamic IP User" as shown in the following figure, and click "Save to take effect".

6.Click "Running Status" to view the interface information, click "Connect" and check whether the WAN port can obtain the IP address. If the IP address can be obtained, the setting is complete.

How to set up a secondary wireless router

1.Turn on the power of R2 and find a network cable to connect from the computer to any LAN port of R2;

2.Open the browser on the computer, enter in the address bar, press enter to enter the router login interface;

3.Enter the default username and password in the login box to enter the management page of the router. Click Network Parameters, select LAN Port Settings, and change the default IP address to a network segment that is not in the same network segment as the R1 intranet (for example:

If the IP address of R1 is, then modify R2 to and click "Save and Restart".

4.After R2 restarts, find a network cable from any LAN port on R1 to connect to the WAN port on R2.

5 After the connection is completed, open the browser on the computer and enter, and follow the settings in step 2 to enter the management page of the router. Then click "Network Parameters" - "Public Network Configuration", select "Network Access Type" as "Dynamic IP User" as shown in the following figure, and click "Save to take effect".

6.Click "Running Status" to view the interface information, click "Connect" and check whether the WAN port can obtain the IP address. If the IP address can be obtained, the setting is complete.

Set up the secondary router, the secondary router when the wireless router uses the setting method: the second router must be a wireless router.

Set Level 2 Routing Method].

1. How to connect two routers.

1. There is a cat (modem): cat (modem) - router 1wan port; Router 1LAN port --- router 2WAN port; The 2lan port of the router --- the computer.

2. No modem: network cable --- router 1WAN port; Router 1LAN port --- router 2WAN port; The 2lan port of the router --- the computer.

Second, the setting method.

Before setting, disconnect the WAN port cable of the second router and plug it in after the setting is complete.

1. Set the IP segment of the second router.

After restarting the router, the address to enter the router is.

2. Set up a second router to access the Internet.

Check the IP details of the computer connected to the first router. (win+r--input, cmd--input:ipconfig all [remember: ip, mask, gateway, dns]).

Set it on the second router, and select Static IP in the Setup Wizard. Enter the IP that the 1st router does not use, and the others: mask, gateway, DNS settings are the same.

Restart your router once it's set up.

3. After restarting the router, the setting is completed, and the line of the 2WAN port of the router is reconnected to make the router 2 network normal.

Turn on the router's wireless function].

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.