What s wrong with the yellow light of the Baojun 510 engine?

The car cannot be started, the idle speed is unstable, the speed is high and low, and the inspection items are as follows: 1. The car battery voltage is low; Specific detection method: test the battery voltage with a three-purpose meter voltage level, if it is below 10V, it is recommended to replace it.

If it is around 11V, it is barely used; Be prepared for replacement. It can be used above 12V; 2. Check whether it is caused by carbon deposits; If you travel about 20,000 km, focus on checking and cleaning the throttle; 3. Inspect, test and replace spark plugs; 4. Confirm the quality of the gasoline added; 5. Detecting the ignition switch; 6. Test and detect the starter, gasoline pump, sensor and other related components of the starting and oil supply system; 7. After powering on, do not start immediately, wait for 30 seconds to 1 minute, and then ignite; See if it works; Regardless of any of the above situations, pay attention to the time when the car cannot be hit once, be sure to play again after an interval of 15-30 seconds to protect the battery but not generate power and prolong its service life.

Personally, I feel that it should be a small fault, and it is recommended that you consult the maintenance personnel of the next 4s to see, or go to the maintenance master to take a look, don't worry too much. The quality of the Baojun 510 car is still relatively reliable.

Hello, the engine light is on, you need to use the computer to detect the fault code according to the fault code to find, if the engine has jitter, it may be the engine cylinder, if the engine is working normally, it may be a line problem, it is recommended to go to the repair shop to check.

The Baojun 510 fault light is on: it is caused by the fuel emission system.

1. When the fault light is on, start and extinguish the vehicle, start and extinguish the car three times after starting the vehicle, you observe whether the fault light is still lit, or it is still lit, you need to go to the store in time to check the fault code, to see if it is an engine problem or a sensor failure, or it may be an occasional failure, you don't need to go to the store in time to check.

2. When the computer receives the parameters of the oxygen sensor, the exhaust emissions seriously exceed the national legal standards, and the internal program of the computer cannot be corrected to the standard range, at this time, the engine control computer will issue a warning light (yellow pollution light on) through the instrument to remind the owner to the maintenance station to check the cause of the engine pollution emission lamp.

1.Vehicle fault light is generally caused by the fuel emission system, you start and extinguish the vehicle when the fault light is on, start and extinguish the car three times after starting the vehicle and observe whether the fault light is still lit, or it is still lit You need to go to the store in time to check the fault code, to see whether it is an engine problem or sensor failure, or it may be an occasional failure can not be checked in time to the store. 2.

When the computer receives the parameters of the oxygen sensor after the exhaust emissions seriously exceed the national legal standards, the internal program of the computer can not be corrected to the standard range, at this time, the engine control computer will send a warning light (yellow pollution light on) through the instrument to remind the owner to the maintenance station to check the cause of the engine pollution emission lamp.

Which engine buckle fault light is on, start the engine into gear and start to open, step on the accelerator and can't get up the oil, ** something is ...... problem

1. Sensor problems.

The sensors mentioned here include the water cylinder temperature and the crankshaft.

Position, air flow, inlet air temperature, oxygen sensor.

When these sensors are damaged, the contact is poor, or the signal is interrupted, the ECU of the car cannot accurately obtain the data of the engine resistance machine, which will cause the engine failure light to turn on.

Solution: It is recommended to replace the new part to solve the problem.

2. Maintenance problems.

Poor engine maintenance is the most common cause of engine failure to light up. All car owners know: the vehicle has a certain maintenance cycle, if the owner does not maintain on time, coupled with bad driving habits, then it will increase the burden of engine operation, and finally can only be reminded by the fault light that the car should be maintained.

Solution: It is recommended that the owner should pay attention to the timely maintenance of the vehicle.

3. Oil quality problems.

Oil quality includes fuel and engine oil, we all know: the fuel filled by the car is generally marked, and the oil is also semi-synthetic and fully synthetic, manufacturers generally recommend the owner to use which grade of fuel, what type of oil, if the owner does not add as required, long-term addition will cause wear and tear of the engine.

4. The mixture does not burn.

Start the spark plug of the Mu Qi machine.

Fault, ignition coil.

Faults, fuel pump failures, oil circuit blockages, etc., can cause poor combustion of the engine mixture. Poor combustion of the mixture results in engine carbon deposits.

or knocking problems, and these will eventually be detected by the engine's oxygen sensor, and after being reported to the ECU, the fault light will naturally light up as a warning.

Solution: It is recommended to find out the cause and replace it with a new part if necessary.

5. Air intake problems.

When the engine burns, it needs to take in the air, and in the process the air cleaner is required.

It is very important that if the air filter of the car is not clean, it will affect the air intake of the car if it is not cleaned regularly, and it will be clogged for a long time, and in serious cases, it will cause the engine failure light to turn on.

Solution: It is recommended to clean the air vapor filter regularly.

Reasons why the engine failure light is on:1Poor combustion state pin ruler; 2.engine knocking; 3.poor quality of fuel source; 4.The engine cylinder is not clean, and carbon is deposited; 5.The computer was unable to obtain engine data from the hail belt.

Baojun 560 car engine, if the engine alarm light is on, it means that the engine system is faulty, and it is recommended that you need to go to the repair shop for diagnosis, otherwise the engine has a big problem with the consequences of cavity slag is very serious, prosperous. Hope!

Reasons why the engine failure light is on 1Poor combustion 2Engine knock 3Poor fuel quality 4The closed part of the engine cylinder is not clean, and the carbon deposit is 5The car is empty and the computer cannot obtain engine data.

The reason why the engine fault light is on 1, the combustion state is not good2, the engine knocks 3, the fuel quality is not good4, the inside of the engine cylinder is not clean, there is a pin deposit, and the computer cannot obtain the engine orange data.

The engine fault light does not mean that a fault points to Brother Xuxiang, it may represent a lot of faults, to know the specific cause of the failure, you need to go to the repair shop or 4S shop with a computer to decode. For the repeated lighting of the said reputation, it may be that the fuel quality is not good or that a sensor is malfunctioning.

Hello, because the signal of the gearbox needs to be processed by the computer, so first check whether the computer control system is faulty. Restart the control panel of the car computer, if the fault light does not light up, it means that there is no fault, the system is false positive, and there is a problem with the computer system.

If the fault does not disappear after restarting, but there is no abnormality in the car during driving (no abnormalities in gears, speeds, etc.), and there is no abnormal noise, it means that the electronic components of the transmission may be damaged.

Solution: The car can continue to drive normally, go for inspection and repair, and replace the damaged electronic components.

If the color of the gearbox turns black and there is an obvious burnt smell, and there are obvious impurities when twisting it by hand, if it is oil, it means that the transmission oil impurities have blocked the solenoid valve. If there are impurities or serious deficiencies in the transmission oil, it is necessary to add or replace the transmission oil, and let professionals conduct a comprehensive inspection of the transmission to completely eliminate the fault.

If the vehicle finds that the acceleration is difficult, the engine speed is high, the gear is sluggish or even unable to shift, and the transmission noise is abnormal, the internal parts of the gearbox may be damaged. If you want to pull over, contact a maintenance professional to come over for maintenance.

Hope it helps.

Summary. Hello, I am your exclusive service technician, attentive, attentive and careful to help you solve the problem of using the car, Baojun 510 engine failure light is lit, this situation is mainly considered for the following reasons. The first common aspect is whether the ignition defect caused by the addition of ordinary inferior gasoline to the oil quality problem is a failure.

The second common problem is that the ignition system failure mainly includes leakage of the ignition coil, too large gap of the spark plug, and poor ignition. The third aspect is mainly the group side, which mainly includes the problem of poor combustion caused by throttle deposition, fuel injector deposition and in-cylinder carbon deposition. Fourth, I would like to consider the sensor, which is generally the oxygen sensor.

Hello, I am your exclusive service technician, attentive, attentive and careful to help you solve the problem of using the section including the car, the Baojun 510 engine failure light is lit, and the following reasons are mainly considered. The first common aspect is whether the ignition defect caused by the addition of ordinary inferior gasoline to the oil quality problem is a failure. The second common problem is that the ignition system failure mainly includes leakage of the ignition coil, too large gap of the spark plug, and poor ignition.

The third aspect is mainly the group, which mainly includes the old throttle carbon deposit, fuel injector carbon deposit, and the poor combustion problem caused by the cylinder carbon deposit. Fourth, I would like to consider the sensor, which is generally the oxygen sensor.

The four-s shop gave me a sensor and the fault light was still on.

In this case, it is necessary to consider the connection line of the oxygen sensor to see whether the line has a short circuit or a short circuit virtual connection fault.

Sometimes it's on, sometimes it's not.

Sometimes if it is bright and sometimes it is not, it should still be a problem of virtual connection of the line.

There is no problem with the engine.

There is no effect on the engine itself.

The light spot must be dealt with.

Yes, if the fault light is on, it must be repaired.

Okay thank you. Well, you're welcome.

The reason why the Baojun 510 engine light is on:

1. First of all, light up the fault lamp, so as to tell the owner that the current engine system is faulty, and it should be checked and repaired in time;

2. Secondly, the fault information of the previous field will be stored and provided to the repairman as a reference during maintenance, so as to solve the fault faster;

3. Furthermore, in order to ensure that the engine can continue to run in the event of a failure, if the detected fault has little impact on the operation of the engine, the computer will directly ignore it, but in fact, the engine is not in a good working state at this time. If a more serious fault is detected, the computer will start the emergency program Lu Xian, and the engine can also work under the emergency procedure, but generally only to ensure that the engine can continue to run without turning off.