What should I do if the Baojun 510 engine anti theft certification fails?

The failure of the engine immobilizer authentication is due to the failure to check the car key, and most of this situation is due to the car key running out of power or a problem with the receiving module. When you encounter this situation, you should check your car keys.

The engine anti-theft system fails to connect with the key, when the key fails, it will show the authentication failure, the vehicle engine electronic anti-theft system is embedded with an anti-theft converter in the car key, when the key is inserted into the ignition switch lock cylinder and rotates to the "on" position, the electronic anti-theft ECU communicates with the key through wireless radio frequency.

The reasons for the failure of Baojun 510 engine anti-theft authentication are roughly as follows: 1. The internal chip of the key is not matched and is not locked (it is not locked in the anti-theft control unit);

2. Anti-theft reading coil failure;

3. Communication failure between the anti-theft coil and the anti-theft control unit;

4. There is no match between the internal fault of the anti-theft control unit and the communication fault of the engine control unit;

5. Electromagnetic interference, etc.

There are two reasons for most of the engine anti-theft authentication failures: one is due to the problem of matching the remote key and the engine computer. There are many reasons for this:

For example, there is electromagnetic interference nearby, there is a large power supply device nearby, in a very open area, etc. The second is that the front windshield film has water (this reason is quite a lot), and the water will flow down the glass into the central control. When applying the film, you must tell the master to pay attention to it, and it is best to put a towel on the center console.

In the above situation, most of the phenomena are brake failure, the steering wheel becomes heavy, and the ignition does not catch the car. This is due to the engine anti-theft system starting, the car is cut off from oil and power, and there is no fire, so there is no oil pressure, so the brakes and steering power basically stop working. For cars that have been equipped with an engine immobilizer locking system; Even if a car thief can open the door, he will not be able to drive away the car.

A typical engine anti-theft locking system works like this: the car ignition key is equipped with electronic chips, each chip is equipped with a fixed ID (equivalent to an identification number), only when the ID of the key chip is consistent with the ID on the engine side, the car can start, on the contrary, if it is inconsistent, the car will immediately automatically cut off the circuit, so that the engine can not start.

This is also the case in my car today, it is a rubber gasket on the clutch switch that affects the switch on, just take the rubber gasket off.

Engine anti-theft certification failed because the car keys were not checked. This situation is mostly caused by the car key or receiving module running out of power. After encountering this situation, you should check your car keys.

The engine immobilizer cannot be connected with the key. When the key fails, the authentication failure is displayed. The electronic anti-theft system of the vehicle engine embeds an anti-theft converter in the car key.

When the key is inserted into the ignition switch cylinder and goes to the "on" position, the electronic anti-theft ECU communicates with the key via radio frequency.

The reasons for the failure of the Baojun 510 engine anti-theft certification are roughly as follows:

1. The chip inside the key is not matched and unlocked (unlocked in the anti-theft control unit) 2. The anti-theft reading coil is faulty.

3. Communication failure between the anti-theft coil and the anti-theft control unit;

4. The internal fault of the anti-theft control unit does not match the communication fault of the engine control unit.

If the question is started with one button, the steering wheel cannot be moved.

Question: The key can't close the door.

Ask how to reset when the power is off.

Ask what happens when you tear it down.

Do many of them have to be set up?

It is to reset it when the power is off, no, if the power off reset is still not good, then you need to rematch the data of the electronic steering lock column.

This situation is generally caused by the data loss of the PEPS keyless entry control module or the unstable voltage of the BCM high-speed CAN, as well as the anti-theft, and then the loss of data of the electronic steering lock post I mentioned above.

Engine anti-theft certification failed because the car keys were not checked. This situation is mostly caused by the car key or receiving module running out of power. After encountering this situation, you should check your car keys.

The engine immobilizer cannot be connected with the key. When the key fails, the authentication failure is displayed. The electronic anti-theft system of the vehicle engine embeds an anti-theft converter in the car key.

When the key is inserted into the ignition car switch cylinder and turned to the "on" position, the electronic anti-theft ECU communicates with the key via radio frequency.

The reasons for the failure of Baojun 510 engine anti-theft recognition as physical evidence are roughly as follows:

1. The chip inside the key does not match the unlock (unlocked in the anti-theft control unit).

2. Anti-theft reading pure liquid coil failure.

3. Communication failure between the anti-theft coil and the anti-theft control unit;

4. The internal fault of the anti-theft control unit does not match the communication fault of the engine control unit.

Hello, I am your exclusive elite technician, we promise to be attentive, careful, and attentive to answer your car questions. Hello Baojun 560 engine anti-theft certification failed this original Hengyou because of the following points, the first is that your remote control battery is insufficient, resulting in the inability to transmit signals to the anti-theft system on the car, the second words talk about blocking is a problem with your key chip, the third Hanzhou dialect is that there is a problem with the key signal receiver on your car, can not receive the signal sent by the key, generally like this situation is caused by the lack of remote control battery, it is recommended that you change a remote control battery first, to see if you can solve the problem, If the problem cannot be solved, then it is necessary to use a computer for further inspection.

Summary. The handling method of Baojun engine anti-theft authentication failure is as follows; 1. Check whether the vehicle is installed with the correct engine anti-theft certification system; 2. Check whether the key of the vehicle matches the engine anti-theft authentication system; 3. Check whether the engine anti-theft authentication system of the vehicle is installed correctly and ensure that it is properly connected; 4. Check whether the battery of the engine anti-theft certification system is normal, if the battery power is too low, please replace it in time; 5. If the above checks do not solve the problem, it is recommended that you contact the local 4S store or car manufacturer for technical support.

Hello. How to deal with the failure of Baojun engine anti-theft certification.

The handling method of Baojun engine anti-theft authentication failure is as follows; 1. Check whether the vehicle is installed with the correct engine anti-theft certification system; 2. Check whether the key of the vehicle matches the large nuclear hole of the engine anti-theft authentication system; 3. Check whether the engine anti-theft authentication system of the vehicle is installed correctly and ensure that it is properly connected; Fourth, check whether the battery of the engine anti-theft certification system is normal, if the battery is too low, please replace it in time; 5. If the above checks do not solve the problem, it is recommended that you contact the local 4S store or car manufacturer for technical support.

The starter also turns and it feels like idling, right?

The engine starter rotates, but there is no power, it may be that there is a fault in the internal return part of the engine, such as damage to the piston in the piston cylinder, insufficient fuel supply in the piston cylinder, etc. We recommend that you go to the 4S shop as soon as possible to check the engine to avoid greater losses.

Then start it for a while, just get up in the morning.

Is the fault light on?

Lights up before it shines.

Could it be the reason for the starter, just warm the car.

In this case, use the decoder to read the fault code first.

Look at what faults, and then deal with them according to the fault code.

Summary. If the Baojun 510 engine fails to pass the anti-theft certification, the brakes will fail, the steering wheel will become heavy, and the ignition will not catch fire. There are two reasons for this:

One is due to the problem of matching the remote control key and the engine computer; The second is that the front windshield film has water (this reason is quite a lot), and the water will flow down the glass into the central control.

What happened to the failure of engine anti-theft certification in Wuling Baojun 510? What to do if the engine anti-theft certification fails, hello.

If the Baojun 510 fails to launch the anti-theft certification of the Zhonghong machine, the brakes will fail, the steering wheel will become heavy, and the large book will not be on fire. There are two reasons: one is the problem of matching the remote control key and the engine computer by the imitation spring; The second is that the front windshield film has water (this reason is quite a lot), and the water will flow down the glass into the central control.

What should I do about that?

Hello, this one can be handled like this.

1.Check if the key is out of power or out of order. 2.Check and check whether the anti-theft system has been locked and whether the starter is running.

What should I do if the car is buried and the car does not catch fire?

Many car owners are very anxious when they suddenly encounter a car that does not catch fire, and their first reaction is that the car is broken. In fact, most of the car does not catch fire is caused by human factors, in many cases can be solved by yourself, below, we will take a look at the reasons and solutions for the car not catching fire.

1. Human operation reasons: the battery is out of power, the fuel tank is out of oil, and the gear is wrong.

Many of the reasons why we usually come into contact with not igniting are caused by improper operation, such as running out of oil, running out of electricity, and wrong gear, and these situations are quite common.

The first type: out of gas. We went out to rescue a car before, and the fuel gauge showed that it was below the red line, so naturally it could not catch fire.

The second type: the battery is out of power. It may be due to the loss of power or the expiration of the battery life due to the long-term headlights have not been turned off, and it is generally recommended to replace the battery in time after 2 years.

In addition, the installation of xenon headlights, high-power audio, etc. are also the causes of vehicle circuit failures. The situation of the vehicle without power is easy to check, just press the horn to know.

The third type: the gear is wrong. When the automatic transmission car starts, the gear must be placed on the P or N gear, if it is placed on the R or D gear, it will not ignite. There are also some manual transmission cars that will not catch fire if you don't step on the clutch.

The reasons and solutions for the old fire of the car not bending.

2. Reasons for the use of sail vehicles: improper oil, no antifreeze, and excessive carbon deposit.

In addition to the reasons for improper human operation, there may also be motor failure, or oil pump oil supply, fuel injector problems, sensor failure, etc., encountering these more complex situations, need to be dealt with by professionals. However, pay more attention to the following items when using a car to avoid these complex situations.

First, there is the issue of oil products. When we used to repair the car, we found that there was water and mud in the fuel tank after disassembling it, and with such oil, it was impossible for the car not to break. Therefore, remind the owner to be sure to go to the regular gas station to refuel, and you can bring a gauze wrapped in the muzzle of the refueling gun to filter impurities.

Second, no antifreeze is added. Some car owners add water or inferior antifreeze to the car, resulting in a particularly cold winter, causing the entire waterway to be frozen, the engine to be frozen and cracked, resulting in the car water pump can not operate, can not catch fire, and injure other parts of the engine.

Too much carbon in the vehicle will also cause the vehicle to not catch fire, and the solution is to run at high speeds to reduce the carbon deposit. In addition, there is a small trick for not ignition, before starting the ignition, first screw the key to the ON switch, and then turn it back, and then turn on the strat switch to ignition, let the computer run to calculate the water temperature and the appropriate air intake, and the ignition will be smoother.