What is the problem of the wireless traveler being disconnected once a minute?

First, it may be that this wireless routing itself is unstable.

Second, it may be that the compatibility between the wireless router and your wireless network card is not good. You try to change to another brand of network card, not TP-link.

There may be interference with other similar wireless signals near your home, change the wireless band of the wireless router, and if not, look at the settings. Update the driver.

If you have a friend, go to your friend's place and try it

Break every minute??

Very regular??

Maybe it's poisoned, right?

And you add a key to the wireless router!!

The problem should be that there is a wireless router of the same model near your home, or your wireless router does not set access rules, resulting in many people occupying the resource at the same time, you can set access rules according to MAC address or SID.

ISP issues: There may be problems or maintenance with your ISP's servers, which can cause your router to be disconnected. Please check with your internet service provider** to see if there are any issues.

Unstable signal: If the router is located too far away from your device or if there is an obstacle, or if the signal is interfered with by other electronic devices, it can cause the signal to be unstable and disconnect. Move the router closer to your device, or try to eliminate the source of interference.

Router setup issues: The router may need to be reconfigured or updated firmware. Please check if the router is configured correctly and try to update the firmware.

Router hardware issues: If none of the above methods work, there may be a problem with the router hardware. The router may need to be replaced or repaired.

In conclusion, if your router automatically disconnects after a few minutes after connecting to the internet, try restarting your router first to eliminate the temporary failure. If the problem persists, consider the possible causes above and take appropriate steps to resolve the issue. If none of the above methods work, please contact the manufacturer or technical support for further advice.

The result of the automatic repull.

Generally, it is due to the fact that the original use of dial-up Internet access, and later changed to the router; And one of the basic settings of dialing up the Internet is still in effect. In IE - Options - Connection - Settings - Properties - Options - Number of Repulls, set to 0 times.

1 If the router moves away from the desktop and tries again, it may be desktop electromagnetic interference2 The wireless part of the router manually selects a different channel, which may be the neighbor wireless network interference.

3 It may be a problem with the routing itself, change routers.

The quality of the network card is not good, the signal interference is large, and the wireless signal is not good.

There is also a network card driver update and a wireless routing update! : Uninstall the wireless card driver. Then restart the computer, and the system will use the network card driver that comes with the system.

Then the problem of disconnection was solved. Remember: be sure to reboot the system.

Otherwise, no NIC driver is displayed.

I don't know.

The router is unstable, and the possible reasons for the network disconnection from time to time are as follows:

1.Poor heat dissipation causes the chip to overheat, which affects the working performance.

2.Electromagnetic interference was observed.

3.The network cable of the router is loosely connected.

4.The router is aging.

The solution is as follows:

2.Try not to use a wireless mouse or keyboard, especially near wireless devices such as set-top boxes. Keep away from microwave, cordless** radiation sources. If possible, the 5GHz router can be replaced to avoid congested frequency bands.

3.Check whether the WAN port and LAN port of the router are loose, and reconnect to ensure a reliable connection.

4.Replace the router.

1. The network is disconnected every few minutes, and sometimes even every few minutes.

2. I can't connect for a long time, restart the router, and then it's fine?

Answer: The router is unstable, strengthens heat dissipation, or replaces high-quality 3, and cannot be reconnected after a short network?

If such problems always occur, contact the operator in time to find out the problem, and I hope it will help you to solve the problem.

This is most likely due to the connection time limit or IP allocation time limit in the route. Check these two settings slowly. If it's a wireless disconnection, the signal may be unstable.

Let's change routers, there may be router problems. Or you don't use the router test to see if the network is disconnected, or there may be a line problem.

Determine whether the cat's connection is stable, the one that has the adsl light to be on all the time (synchronization is normal), determine the method, router login - dial-up method (manual connection) - connect to the network - wait for him to disconnect the network.

If the network is disconnected and you restart the router to recover, it may be a problem with your routing.

2.If the reboot cannot be restored, if you want to restart the cat, there may be a problem with the cat.

3.Other possibilities are not ruled out.

You enter,Set it inside,Router mode is selected as 11G,Save it won't suddenly be out of network.。

Intermittent disconnection of the wireless router may be due to the computer itself and network problems. If it is a wireless network, if the wireless network is always dropped, then please check the distance between the computer and the wireless source and whether it is blocked by things that affect the network transmission. See if there are any obstructions, such as walls, or doors, etc.

There is a lot of interference, and it is difficult to check the general signal interference, so it is best to see if there is a user who forcibly rubs the net, and the transmitter that rubs the net affects the normal use.

Workaround for intermittent disconnection of your wireless router:

1. The occasional inability to access the Internet on a computer or mobile phone is actually a DNS resolution error, which can be solved as long as the DNS cache is cleared;

2. Click Start and Run;

3. Enter cmd in the box and click OK.

4. After the interface comes out, enter ipconfig flushdns at the cursor and press enter.

5. The prompt "Successfully flushed the DNS Resolver Cache" appears, it means that the clearing is successful, and you can surf the Internet without worry.

During the use of the router to surf the Internet, there is a periodic network disconnection, that is, a fixed period of network disconnectionYou can follow the steps belowThe WAN port of the router is configured to access the Internet in PPPoE, and the PPPoE connection is disconnected after 24 or 48 hours of Internet access

The problem is that the network service provider sets the IP address lease period to 24 or 48 hours, and when the set time reaches after authentication, the user will be forced to disconnect from the IP address, which is not a router problemPlease set the WAN port of the router to automatically connect to ensure that it will automatically connect to the Internet after each disconnectionYou can refer to Troubleshooting 3

If you set unreasonable Internet access control rules on the router, such as specifying that the computer cannot access the Internet at a specified time...Then within the specified time, the computer will be disconnected...You can log in to the router interface and turn off parental controls and Internet access controls (or Security Settings >> Firewall Settings and turn off the Firewall Master Switch).

Restore the default reset settings, set a password for wireless networking, and consider whether there is an ARP attack for multiple people to share (install relevant anti-virus software to solve the problem). If you still consider whether the wireless router generates too much heat, if the needle in the wireless router network interface is 4 pin instead of 8 pin, it must be caused by the manufacturer cutting corners, and consider returning it to a good wireless router.

。。Use it well, and didn't move its setting parameters, for no reason this problem, it is estimated that this router is convulsed, and there are devices that work unstable, causing it to crash after a while. And the initialization of the restart can only be managed for a while, and the problem will occur again.

It is recommended to use another wireless router to replace the original router for testing and verification.

。。Cross the computer over the router and directly on the LAN port of the broadband modem, and dial-up Internet access to test the effect. If there is no intermittent network disconnection, the problem is with the router; If there is also an intermittent network outage, most of them are external network problems, and the customer service of the network operator can send troops to repair the fault.

In the LAN settings, set the address lease period to the longest on the line, you can disconnect the network once every two days, if you can't stand it for two days, you can only set the static IP.

Take a look at the route, "network parameters", if you don't select "automatically connect after booting and disconnection", sometimes this kind of problem occurs.

Buy a new computer, call a telecom person to re-pull the network cable, it's as simple as that.

<> wireless signal is unstable and the signal strength is insufficient. Use a wireless signal monitoring software to monitor the wireless signal to see if the strength is variable and intermittent. When the wireless signal passes through the outdoors, it will be unstable due to the influence of weather changes, and when the signal strength is insufficient, it will be intermittent.

Try to adjust the position and angle of the antenna of the wireless router, and then adjust the angle of the computer position, or the angle and position of the antenna of the computer wireless network card, so that the wireless connection signal is the best and the connection speed is the fastest.

You set up an automatic connection, indicating that your higher-level network is automatically obtained through the router, and the gateway of your router may conflict with other routers, for example, the IP address of the first router is , then it routes out no IP is generally so) The IP address obtained by the second router is any of them, then the IP of the second router itself can not be changed to, to The third must be, otherwise when the IP is converted to the first level of route, The second level of routing is easy to conflict when obtaining IP, resulting in no access to the Internet, the solution, you can change the address of your router to, restart it, of course, it can also be, and so on.

Re-set the debug router.

The easiest way is to reboot and then restore the factory.

The steps on how to set up the router are as follows:

The wireless router is powered on, then plugged in the network cable, the incoming line is plugged into the WAN port (usually the blue port), and then the network cable connected to the computer is plugged into any LAN port.

After connecting the wireless router, enter the address you see on the router in the browser, generally of course, if you use ** online Internet at home, then you need to prepare an additional modem.

After entering, you will see that you enter the corresponding account and password, and generally the newly purchased ones are admin.

Once you are sure to enter the operation interface, you will see a setup wizard on the left.

Enter the interface of the setup wizard.

Go to Internet Access Settings.

Click Next, enter the Internet access method settings, we can see that there are three Internet access options, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

I chose PPPoE because I dialed.

8.If you choose PPPoE dial-up Internet access, you need to fill in the Internet account number and password, which should be understood by everyone, and there will be an account number to open broadband, and it is OK to fill it in.

9.Enter the wireless settings, we can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill in as you like, and then the mode mostly uses 11BGNFor wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe that it will not be hacked and rubbed by the network.

10.The next step is to set it up successfully.

You enter the routing settings There is a setting about automatic disconnection, for example, his default setting is 4 o'clock in the afternoon, then he will be disconnected at 4 o'clock in the afternoon every day, you have to connect again to get on, it is estimated that your default is turned on, and you can turn it off when you go in.

It should be a problem with the router, you can reset the router and upgrade the software version. Let's see if there is any problem, if it doesn't work, you have to change the route, I have also encountered such a problem.

The Tengda router I use, open the router settings**, wireless settings - wireless timing switch, click enable - wireless shutdown time period, and set it yourself.