How to make the system small

I just made a system.,First make a default system.,Then install the firewall.,Then install the software you need.,It is recommended that you install the software as much as possible from the official ** up and down.,In this way, the possibility of poisoning and pressing the plug-in is smaller.,Internet café?,It's nothing more than installing online games and stand-alone games.,Stand-alone can go to the science and technology city to sell a few good CDs.,It's not used once.,And it's generally more reliable than the Internet.,Relatively very affordable.。 After installation, back up the C drive, so as not to show that the instructions are not wasted. In this case, even if there is a problem with the system, just restore it, one has written the registry, so the software you installed before can still be used, and if you have the conditions, you can also do a full backup, even if it is an 80G hard disk to do the image at most 40 minutes, which is faster than a separate redo system.

First of all, let's take you to the next explanation of Kingsoft Cleanup Expert and other things, which are very easy to use and clear about the plugins that are not needed. Check how secure the system is.

Upgrade all the online games you have installed, otherwise it will be too much trouble to update them after you finish the system. If all the software works and all the games can be played, then upgrade your antivirus software one last time.

After the upgrade, you have to disconnect the network cable, and try not to plug in the USB flash drive on this unprotected parent machine. All-round antivirus.

Confirm that there is no virus, you start to optimize, you can do the system before going to the Internet to write the optimized registry, because this is relatively low technical content and easier to operate. I also recommend a DIY software for rainforest wood, which is quite easy to use. Hehe, everyone's hello is really good, and I will recommend it to you today.

As for the simplicity of the instructions, you can remove all the redundant components from the add-and-remove program, and of course, all of this can be done with the tools I just mentioned. Hehe,My system doesn't even have a help file.,Start super fast.,Boot 120m hehe.,It's okay.。

It is also necessary to ensure that each partition has more than 15 percent of the remaining space.

When you think you have done everything you think you need to do, then you can defragment it, and finally uninstall the antivirus software and the Kingsoft cleanup expert you just mentioned.

Try a lot of XP Internet café master plate making, I used to be in an Internet café.

(1) Minimal system method.

The minimum system refers to the most basic hardware and software environment that can turn on or run a computer from the perspective of maintenance judgment. The minimum system comes in two forms:

1.Hardware minimum system: consists of a power supply, motherboard, CPU, memory, graphics card, and display. The whole system can judge whether these core accessories can work normally through the alarm sound of the motherboard and the boot self-test information;

2.The smallest system that runs software: consists of a power supply, motherboard, CPU, memory, graphics card, monitor, keyboard, and hard disk. This minimal system is mainly used to determine whether the system can complete normal startup and operation.

The minimum system method is mainly to determine whether the system can work normally in the most basic software and hardware environment. If it does not work properly, it can be determined that the most basic software and hardware are faulty, and the scope of finding faulty accessories can be narrowed.

ii) Substitution method.

The replacement method is a maintenance method to replace the parts that may be faulty with good parts, and judge whether the fault phenomenon disappears. Good parts can be of the same model or different models. The order of substitution is generally as follows:

1.According to the phenomenon of failure, consider the parts or equipment that need to be replaced;

2.Replace the replacement parts in the order of ease and difficulty. For example: memory first, CPU, then motherboard.

3.The first step is to examine the connection wires, signal lines, etc., that are connected to the suspected faulty parts, followed by the replacement of the suspected faulty parts, then the replacement of power supply parts, and finally the other parts related to them.

4.As a rule of thumb, consider the first part to be replaced based on the failure rate of the part. Parts with a high failure rate are replaced first.