The computer is turned on and stopped in the Tab interface, and the master helps, waiting next to th

I'm a webmaster, and I have the following possibilities:

1. If there is a problem with your system, reboot and press F8 to enter the selection interface, and select the last correct restart.

2. If it doesn't work, unplug the memory module and plug it back in.

2. If the above is not easy to use, redo the system or hang the hard disk on another machine as a boot disk.

3. No matter how bad it is, it is very likely that your hard disk boot area is broken, find the original factory or store to monitor it.

I'm not a master, but I'm used to doing this job, I hope it helps you, hehe.

press tab to show post screen

This is a self-test.

Staying here means that there is a problem with the self-test.

You can press tab to see if there is a problem with the self-check.

Get the right medicine. In general, you can select the option of Quick Self Test and Fast Detect in the BIOS.

The display does not need to be warmed up.

My machine has been like this for the past two days.

It came after I was overloaded with a machine.

The first time I unplugged the cable from the optical drive, plugged it in, and it was ready to enter the system.

The next day, I turned on the phone like this again, I pressed del to go in and pressed everything, nothing was modified, and I was able to enter the system again when I exited.

Award BIOS 2 Short: General error, please go to CMOS Setup and reset the incorrect option.

ami bios

2 Short: The memory ECC verification error is incorrect. Setting the memory option for ECC check to disabled in CMOS setup will solve the problem, but the most fundamental solution is to replace a piece of memory.

I don't know anything else.

Dual Channel Mode Enabled is enabled.

You have to go into the BIOS and turn on the dual-channel mode.

You start the computer, press and hold the del, enter the BIOS interface, and you can make changes.

Just reboot a few more times!

Restore the BIOS settings and you're good to go

1. Since the motherboard log display time is very long when the computer is turned on, it should be caused by the problem of the data cable or the motherboard battery is dead. You can try to change the data cable of the optical drive and replace the battery of the motherboard.

2. It is also possible that the power supply is insufficient, which causes the computer to fail to detect the master-slave IDE device normally, so the power consumption becomes smaller after unplugging the power cord of the optical drive, and the computer can detect normally, and the startup will become faster. If that's the case, then it's time to replace the power supply.

3. I don't know if there is a disc in the optical drive, usually don't put the disc in the optical drive, even if the optical drive is easy to use, having a disc will increase the computer boot time!

In addition, open Device Manager in Windows and close all useless IDE device channels, that is, under the "Advanced Settings" tab of the "Primary (Minor) IDE Channel Properties" window, select "None" in the "Device Type" drop-down menu of all undetected devices in Device 0 and Device 1 to confirm the exit. In this way, those useless channels will not be detected when Windows starts, and the boot time will be much reduced.

Hope it helps!

Have you ever encountered the phenomenon of pressing f1 or f2 when the computer is turned on, and you have solved such a problem in this way. Today we're going to teach you how to turn off this pesky F1 key.

Maybe it's because the computer's program system is slow, and I don't know.

The computer boots up to press the tab key to enter the system, otherwise the computer has been black, the system boots up when the boot screen is displayed, press the tab key to cross the display of this boot screen. So it is possible that the boot screen data in the BIOS is corrupted. Try to restore the default settings of the BIOS to solve the problem, otherwise you will have to reflash the BIOS.

You unplug the power supply and try to change the cable.

Turn off the power or do the system directly.

1. The motherboard battery is dead!

2. Disassemble the chassis and replace it with a battery, which is easy to find, it is a button battery, which is the same as the one used on the car key. The battery looks like the one above, and you can do it yourself.

1。If this is accidental, usually restart the computer and the symptoms will go away.

2。Antivirus is not thorough, use antivirus software, full scan and custom scan. If you find a Trojan or virus, you should restart it immediately, restart the computer, and go to "Quarantine|".Recover", completely remove trojans and viruses.

3。Software conflicts, incompatibilities. Install redundant similar software and delete it.

4。The computer system is interfered with by stubborn viruses and Trojan horses or worms, or system files have been lost. There are new vulnerabilities in the system waiting to be installed, and you can install them with relevant software.

5。Poor contact and loose or dust-covered graphics card or memory CPU, or fan. The memory CPU is overheated and the heat dissipation is not good.

6。There is a bad review plug-in on the computer. Scan it out, clean it up immediately or the disk is too fragmented, use system tools to clean up the fragments. You can check them one by one, or reinstall the system.