How to make an oily finish? What are the specific steps to make an oil mixed finish?

The specific steps to make an oil-mixed finish are as follows.

1) Grassroots treatment. The same construction method as for blending lacquer (varnish) finishes.

2) Brush the back coating. The back cover coating is made of clear oil, gasoline and varnish, and some red clay can be added. After brushing, check whether there is any omission, and pay attention to whether the paint color is correct, and finally wipe the paint stained on the hardware and other places.

3) Scrape putty. After the clear oil is dry, the nail holes, cracks, knots and defects are scraped and smoothed with gypsum putty, and the putty should not be soft or hard, not out of honeycomb, and not falling down. When scraping, it should be wiped horizontally and vertically, and the putty should be scraped into the nail hole or crack.

If the seam or crack is wide and the hole is large, you can use a knife or shovel to squeeze the putty into the gap, and scrape it flat after embedding the putty. The putty on the surface should be scraped clean, and there is no loose putty and residue.

4) Polishing. After the putty is dry, use No. 1 sandpaper to polish, the grinding method is the same as the bottom grinding method, but be careful not to grind through the paint film and protect the edges and corners, leaving no loose putty. When sanding is complete, wipe the sanded powder clean with a damp cloth.

5) Brush the paint for the first time. First, the color lead oil, varnish, clear oil, gasoline, kerosene are mixed together, stirred evenly and sifted, red, yellow, blue, white, black lead oil can be blended into various colors of lead oil paint, its consistency to ensure that the bottom of the cover, no flow, no brush marks shall prevail. The order of application is the same as that of the back coat.

6) Scrape putty. After the first coat of paint is dry, scrape the shrinkage or defects of the bottom putty with gypsum putty.

7) Beat sandpaper for the first time. After the putty is dry, sand it with sandpaper below No. 1.

8) Brush the paint a second time. The operation requirements are the same as the first pass.

9) Beat sandpaper for the second time. After the putty is dry, sand it with sandpaper below No. 1. When using new sandpaper, you should first grind two pieces of sandpaper in parallel to grind off the coarse sand grains, so as not to scratch the paint film during sanding.

10) Brush the paint a third time. The operation method is the same as the first pass. Due to the large viscosity of the blending paint, it is necessary to brush more and more rationally when brushing, and pay attention to the full oil and agile action, so that the paint brushed does not flow or fall, the light is uniform, and the color is consistent.

The paint process is divided into oil mixing process and oil cleaning process, the oil mixing process is to brush the solid color paint on the Aosong board, which can reflect the original paint color process, and the clear oil process is to brush the varnish on the veneer, which can reflect the original texture of the wood process, and the steps are the same as those upstairs. Hope.

The oil mixing process is a design style based on oil mixing decoration in many decorative styles to stand out, it is deeply loved by customers for its rich and lively colors, good visual effects, and the effect of oil mixing can produce different effects when buying furniture. Oil mixing is a process in which the painter sprays the wood with a colored opaque paint after the necessary treatments (e.g. repairing nail holes, sandpaper, scraping putty). Oil Mixing Process - Classification Oil Mixing Process The oil mixing process is divided into different construction processes such as painting, painting and painting, and each process has its own characteristics.

Generally, the ordinary process is painting, and the painting effect is general, and there will be brush marks on the paint film, which cannot become an advanced process. The middle and senior processes are mainly painted or painted, and the board finishing requirements are not very high, generally using large core board substrates, pine or willow, beech and other hardwood closures, and MDF can also be used for modeling. Paint is an advanced process, wood and the bottom treatment is the same as the intermediate process, but it is different in the paint process, the paint is wrapped in gauze with absorbent cotton, dipped in diluted nitro enamel, slowly rubbed on the surface of the wood, generally rubbed more than 10 times, and finally can achieve a good effect.

Oil mixing process - types of oil mixed paint Alkyd blended paint At present, there are many types of paint that can be used in decoration, and the main ones that can be used in the past are alkyd blended paint or nitro blended paint, and now there are many types, polyester, water-based paint, etc.; The construction is becoming more and more convenient and the quality is getting better and better. Oil-mixed paint covers the natural color of wood, mainly reflects the color of the paint itself, the main popular practice of clear oil in the early stage of home decoration, such as beech, etc., the paint mixed with oil is opaque with color, and the wood grain and woody color of the wood can not be seen after brushing.

If you use an electric drill, if you don't have much, add some water and stir it evenly with a stick.

It is putty powder and the paint that is planned to be used for modulation. I hope my answer can help you.

There are a lot of MDF substrates and oil mixing, but if you batch putty on MDF, it is best to use putty!

The finish is made of Aosong board - this should be a requirement of people, not necessarily to use it.

Mixed oil is white paint (generally referred to as wood paint).

1. The surface of the wood is full of putty scraped (putty, generally one time); 2. After drying, polish and smooth; 3. Paint for the first time and repair after drying; 4. Brush the second time (2-3 times is fine). Except for the last coat of paint, each side of the paint should be sanded with fine sandpaper after drying.

Oil mixing process - refers to the process of wood making, the surface finish is treated as artificial wood veneer (closing line). After the base layer and paint treatment, the color of the paint reflects the surface perception of the process. The color of the oil mixing process is relatively simple, such as:

White. Mixed with oil is dead paint, which is not transparent to the bottom and only reflects the color of the paint.

The paint process is divided into oil mixing process and oil cleaning process, the oil mixing process is to brush the solid color paint on the Australian pine board, which can reflect the original paint color process, and the clear oil process is to brush the varnish on the decorative panel, which can reflect the original texture of the wood process.

The materials of the cabinet can be medium density board, large core board, finger joint board, moisture-proof board, etc. These boards are made of cabinet materials, and the steps of making white oil in the decoration are as follows: the first step is to scrape the putty twice, the second step is to scrape the transparent putty twice, and the third step is to brush the varnish four times, and the polyester white bottom is four times, and the polyester white surface is five times.

I hope my answer can help you.

You should say what is the material of mixed oil, home decoration is generally furniture wood veneer or solid wood surface mixed oil, around the artificial and auxiliary materials ** slightly different. The white mixed oil on the surface of the door casing, window casing and curtain is calculated according to m. Furniture is mixed by **according to the material, and the type of furniture is different**.

According to the budget of our company in Zhejiang, I will report it to you Project name Unit price (yuan) Unit Main material Accessories Machinery Labor Loss Flat white mixed oil spraying process 90 38 11 3 35 3 Special-shaped white mixed oil spraying process 100 40 13 3 40 4 Flat wall mixed oil 285 120 30 5 100 5 Solid wood line white mixed oil 6 m Modeling wall mixed white mixed oil 370 165 40 5 125 5 Wooden shelf white mixed oil 120 m 30 15 5 65 5 Fixed wooden frame glass partition white oil mix 400 200 35 5 140 20 decorative column white oil mix 145 m 53 20 2 65 5 veneer baseboard white oil mix 35 m 12 5 3 14 1 flat solid door white oil mix 660 fans 335 30 10 205 20 louver door white oil mix 540 265 40 5 150 20 solid double-sided door white oil mix 780 fans 400 40 40 10 280 20 finished door paint (white oil mix) flat door 400 leaves 225 10 5 150 10 Line Door 400 225 10 5 150 10 Concave and Convex Door 450 255 10 5 160 20 Wood Frame Glass Door 400 230 10 5 145 10 Louver Door 500 300 10 5 165 20 Door Cover and Dumb White Mixed Oil 90 m 36 18 2 32 2 Covered Door Cover and Dumb Solid Wood Trim (Single Sided) 28 m 10 2 2 11 3 Window Cover and Half Covered Door Cover White Mixed Oil 80 m 37 16 2 23 2 Concealed curtain box white oil mix 70 m 35 11 2 18 4 Surface-mounted curtain box white oil mix 100 m 55 16 2 25 2 Cabinet wood upholstery white oil mix 100 65 10 2 20 3 Decorative cabinets and bookcases white oil mix 610 220 170 4 200 16 bedside table white oil mix 320 pcs 153 70 3 88 6 drawer white oil mix 70 That's pretty much it, Welcome to add (this ** to 03 standard combined with the local market of our company's own quota, the company is located in Ningbo, Zhejiang) other areas for reference only.

First of all, you should explain that the worker you are looking for is a contractor, or a contractor Contractor Contractor Material, that is, how much money he will quote you a flat, set this**, if it is a contractor, that is, the worker is just doing work, you buy your own lacquer Newspaper**Generally a square to survive** Some are reported even the plates are counted, if you are looking for a home improvement company, it is recommended that you ask them to ask some I am doing environmentally friendly water-based paint, if you are Shijiazhuang you can add me can help you solve some home improvement problems

To put it simply, the oil mixing process is: the wooden board can be water-based putty batch, repair nail holes, sanding and smoothing, remove dust, and then you can brush muddy water paint. If it is MDF, putty should be made in putty batches.

The oil cleaning process is: first remove the stains on the veneer, then brush the primer, putty to repair the nail holes, sand, remove the dust, and then brush or spray paint. The process of sorring, also known as color repair, is to process the substrate and use sandpaper to sand away pencil marks and other dirty things left by carpentry on the panel.

Make a head primer to play a sealing role and prevent the nails from rusting. Adjust the gray and repair the nail holes and seams, and pay attention to the color to be consistent with the color of the panel. Burnish.

Do the primer. Note: The number of paint passes depends on the depth of the panel texture, the thickness of each paint, and the degree of closure required by the customer (such as:

semi-enclosed or fully enclosed). The filling of the grain mainly depends on the primer, the primer fills well, and the sandability is better than the topcoat, and it is cheaper than the topcoat.

Of course, in the process of making the primer, depending on the situation, it is necessary to polish, polish and spray colored transparent paint. Before spraying the color paint, make a sample according to the requirements and let the owner confirm it first. Under normal circumstances, it can be used as a topcoat without sanding.

You can also spray the primer all over and polish it when it is dry. Make a clear finish coat to protect the color and increase the feel. Special Attention:

a. The effect of color paint spraying is the best. b. Master the viscosity of the color paint, adjust it a little thinner, and repair it several times to ensure the accuracy and uniformity of the color. If it is sprayed at one time, the technical requirements are quite high, and the color is not easy to master.

c. The same panel, the same paint, but the more times you spray, the darker the color, and the lighter the color if you spray it less once. d. The color of the paint and the color of the panel also have a lot to do with it: the same color paint, the same construction, but the final effect is different when sprayed on different panels.

e. Some panels themselves have shadows, and there are differences in color shades, and after doing the color paint, they will feel flowery and uneven, but this is not necessarily caused by construction. f. If the old furniture is to be renovated to make paint, you must first try whether it will go oily, because there may be some oil or wax and other substances on the old furniture. If the oil is gone, the color effect is ugly.

g. Once the panel is bought, the project manager generally arranges workers to brush the primer to protect the board.

Chromatography is a variety of colors that are painted after adding white and black. It is only different in lightness and purity, and the hue remains the same.

However, black, white, and gray are not included in the color register.

From the perspective of the industry, the clear oil should be the natural color, that is, the solid color paint shows the color of the paint, and the varnish should show the effect of wood grain; There are many processes for clear oil, including color repair, base color repair and face color repair. At the same time, according to the different materials, according to the requirements of the painting, there should be material adjustments. The so-called color and color are different names for the construction personnel to fix the color of the different techniques and processes.

Who do you paint and who is responsible for training you?

If you want to mix paint on blockboard, you don't have to put veneer. It's just that if you don't paste the veneer, it's more tiring to paint, especially the section of the woodworking board must be uneven, and the painter should fill it with putty and then paint it. That's why the painter will ask for another layer.

It's perfectly okay not to stick.

You can't directly mix oil, Gao pine board or veneer, the master is right.

Suggestions for professional plate - Dr. Niu plate.