How does my computer get into the settings of the cat .

Open the control panel, find the connection in the intenenet option, then see your connection, and set it up! ~1

You need a router to enter the settings page.

General"Cats"It doesn't seem to have this feature in routers.

1. Enter the IP address of the cat in the browser, and you can view the identified IP address on the back of the cat).

2. Check the username and password identified on the back of the cat.

3. Enter the password in the login interface and click Login.

4. You can see that you have logged in to the background interface of the cat.

The method is as follows: 1. The two interfaces lan1 (connect to the computer) and lan2 (connect to the wireless router) directly connect the network cable to the fiber optic modem; 2. Then the network cable is connected to the router at another end, there are many LAN ports on the router, and you can directly connect a network cable to the computer; 3. If it is a wireless router, then the mobile phone and other wireless terminals can be connected to this router, and the computer is connected by wire, and the connection must be set on the computer before it can be used.

The working principle of extended dataThe baseband modem consists of transmitting, receiving, controlling, interface, control panel and power supply. The data terminal equipment provides the transmitted data in the form of binary serial signals, converts them into internal logic levels through the interface and sends them to the transmitting part, and sends them to the line through the modulation circuit modulation into the signal required by the line. The receiving part receives the signal from the line, which is restored to a digital signal and sent to the digital terminal equipment after filtering, anti-modulation, and level conversion.

An optical modem is a device similar to a baseband modem, which is different from a baseband modem in that it is connected to an optical fiber dedicated line and is an optical signal.

There are two situations when a cat connects to a computer:

1.Direct connection between the cat and the computer: Use a network cable to connect directly to the network card port of the computer from the ADSL port of the broadband cat, set up broadband Internet access, and enter the broadband password.

2.Connect the broadband modem to the router and then connect it to the computer: Use a network cable to connect the LAN port of the broadband modem to the WAN port of the router, and then use another network cable to connect it to the computer from the LAN port of the router.

After setting up the router to automatically dial up the Internet, you can go online after slow change.

I hope the above methods about connecting cats to computers will be helpful to you.

1. The computer network cable is connected to the network port of the router, the WAN port of the router is connected to the LAN port of the optical modem, and the PON port of the optical modem is inserted into the optical fiber entrance. 2. Log in to the router settings page. 3. Sometimes after connecting to the line of Companion Shenchang, the input setting address cannot be displayed.

Click the restart button on Lu Xiaosui's device, and that's it. 4. Follow the prompts to select the method of connecting the reed grill network, set the wireless password, etc., and click OK. 5. Wait for the system to save the settings.

I think you're referring to the router, and the username and password of the router are in the manual. It's generally admin. This is not the same thing as your username and password for surfing the Internet.

Once you're on the router, set up a username and password to surf the internet. In the future, you don't have to enter it when you go online.

It's different, if it's the latest telecom cat with routing, the username and password are on the label behind the cat device, or look at the attached manual, there should be a saying.

Generally, the reverse side of the cat has a prompt account and password, not an Internet account and password.

The account and password are admin if you haven't set your own password.

Create a new connection, then enter the IP address in IE, then enter the login account password (under the cat), enter, enter the Internet account and password, and dial up.

1: Device connection.

Description: 1. The leftmost side is the ** line.

2. The middle is the network cable, and the other end is inserted into the computer network card.

3. Black is the cat's power cord.

2: Double-click the desktop broadband connection icon.

Open Online Neighbors, click View Network Connection on the left, select Create a new connection, and then follow the prompts step by step, hehe.

Open the network connection, create a new one, and you're done.

Router Connection Modem Steps:

Step 1: Connect the WAN port of the router to any LAN interface of the optical modemStep 2: Reset the router and press the RESET button on the router with a pin or other items.

Step 6: Click "Done" and the router will restart automatically.

It is to change the original network segment to the new one, because the telecom optical modem uses this network segment, and the router cannot be the same as the optical modem.

Network cable connection, one end to the computer, one end to the cat's WAN port, and then establish a connection on the computer, the steps are as follows:

1.Right-click on the NIC neighbor on the desktop Properties Create a new connection Next Connect to the Internet Next Set My Connections Manually Connect with a broadband connection that requires a username and password Next ISP

2.Enter your username and password and uncheck the box before "Make it your default internet connection" Next: Check "Add a shortcut to this connection on my desktop" Done: Click Connect to connect to the Internet.

Note that in the future, you can connect to the Internet by double-clicking the broadband connection of the desktop directly every time you turn on the computer.

Just tie the cat to the computer.