Is there a skill for a novice to learn to ride a motorcycle

The throttle and clutch should be well coordinated.

The following are the skills for learning motorcycles: 1. The first time you ride a motorcycle, you must master the correct driving posture. In any case, it is necessary to maintain a correct and relaxed driving posture and operating skills.

2. Maintain the balance of the body. Because the body is not stable, it is impossible to manipulate the clan with ease. Of course, it is also necessary to keep the motorcycle balanced and stable.

3. Even if the balance is stable, do not press the car bureau stiffly. Because of the excessive force, it is difficult to operate easily, and the inherent performance of the steering mechanism of the motorcycle cannot be fully utilized. 4. Be able to move the body freely.

That is, you can change the posture of the body according to the needs of the operation, or add weight to the pedals or saddle. Or change the posture to reduce the weight of the pedals and saddle to achieve body balance in different states.

How to ride the motorcycle quietly bent and wide tow car, novice training must pay attention to these points, come and take a look.

1. Start: After the engine starts, it must be warmed up for 3-5 minutes before it can start driving. Engine warm-up is a task that cannot be ignored, especially when the ambient temperature is low, it is even more important, but it should not be blasted to speed up the warm-up.

The engine with insufficient preheating temperature will aggravate the wear and tear of cylinders, piston rings, rocker arms and other parts during operation. Before starting, you should observe your surroundings and give a signal. The key to starting is to coordinate the movement between the throttle and the clutch.

Hold the clutch handlebar, hang up the low-speed gear, gradually relax the clutch handle with the left hand, and slowly refuel with the right hand, if the engine has a tendency to turn off the flame, you should quickly add some oil, if the engine speed is higher, you should reduce the throttle, try to control the engine speed is not too high, so that the engine has been stable in the process of the clutch from "starting to engage" to "fully engaged".

2. Shifting gears: After the motorcycle starts, the next step is to accelerate the operation of shifting gears. When changing gears, the clutch "disengages" during this period of "empty walking zone", which can neither accelerate nor control the speed of the motorcycle with the throttle, but can only be a kind of "inertia" driving.

Therefore, it is necessary to keep the "disengagement" time of the clutch as short as possible. When shifting from low gear to high gear, first accelerate, then close the small throttle, quickly grasp the clutch handle with the left hand, disengage the clutch, hang up a higher gear, and then easily open the clutch handle, and then increase the throttle, according to the essentials to gradually shift gears to reach the top speed of the gear.

When the motorcycle is driving, when the engine power is insufficient (such as uphill) or there are obstacles on the road, you should change the low gear in time. The essentials of switching from high-end to low-gear are: first close the small throttle, reduce the speed, quickly grip the clutch handlebar, change to the desired gear, and then gradually relax the clutch handlebar while increasing the throttle.

When changing from a high to a low gear, the speed must be reduced to a speed similar to that of the shifting gear. Otherwise, due to the high speed of the vehicle, the engine will produce a large restraining force after the gear, causing damage to the relevant transmission parts.

3. Parking: When you need to stop, close the small throttle first, hold the clutch handle with your left hand and hang the neutral gear, brake the front and rear wheels evenly at the same time, and master the slow and soft operation process when operating the braking system, especially on wet roads, smooth roads and turning places, you must use the braking system carefully and gently; When the car is sold in a high-speed emergency state, you can't brake suddenly, you should first pinch and step lightly at the same time to quickly release it, and then brake.

There are three main tips for novices to drive motorcycles. The following is a detailed introduction to these three tips: 1. Startup:

Shift the gear to neutral gear, hold the clutch with a flame-out switch, pull the flame-out switch to the on-on position, and if there is a damper, pull the damper appropriately. 2. Starting: Special attention needs to be paid to the coordination between the clutch and the throttle.

After holding the clutch tightly, shift to first gear and slowly release the clutch. The clutch is released until the car shows signs of moving forward, and the clutch is suspended and released. 3. Upshift:

Each model of motorcycle has a different gear ratio, and the shift speed is not very different. Taking the five-gear model as an example, basically the first gear starts at a speed of about 15km/h, the second gear is about 25km/h, the third gear is about 40km/h, and the fourth gear is raised