How to install and how to wiring? How to connect and how to wiring?

1. In the first step, we first connect the VGA cable to the monitor, and fix the two screws behind after connecting. The main reason for fixing is the concern that the connecting line will be caused when it is moved.

You didn't specify the specific scenario and situation of the wiring, which is not accurate based on the current situation. Different equipment and systems have different wiring methods and standards, and they need to be wired according to the actual situation and relevant standards. Before wiring, you need to carefully read the instructions of the equipment or system, and follow the manufacturer's standard wiring methods for fiber empty, and the following are some common basic wiring methods:

1.Choosing the right cable: Cables play an important role in electrical equipment, and it is necessary to select the right cable according to specific electrical parameters, environmental conditions, and special requirements.

2.Determine the connection method: Before connecting the wires, you should choose the appropriate connection method according to your needs, such as welding, threading, jacks, etc., and different connection methods are suitable for different occasions.

3.Wire number marking: For ease of management and maintenance, wire numbers are required to avoid wiring errors and confusion.

4.Check the electrical system before wiring: Before wiring, the electrical system needs to be inspected to ensure the safety and stability of the electrical system and carry out the necessary protective measures.

Before carrying out any electrical wiring work, it is important to understand the relevant safety standards and specifications to ensure your own safety and the safety of others. If you are unsure how to proceed with the wiring, please consult a professional for advice or seek the relevant installation and repair services.

What kind of wire is it connected to?

If it is connected to the switch socket, you can refer to the promotion book according to the following figure to make a connection:

How to wiring? 5. Next, Tong shouted to fix the terminal with tape, remember to buy insulating tape, imitation electrician. (If the wire is directly connected to the screw, it will not be fixed with tape).

Wrap the connected wire with tape a few times, fix it, and pull the tape tighter and tighter. 6 66, after the wire is restored to the original place, so for the sake of beauty, push the electric switch on the power transmission, try to turn on the light switch, see if the light is on, if it is lit, it means that the wiring is successful, if it is not lit, it means that there is an error in one of the above links.

Wiring 1: single-control single-switch connection method.

The structure of the single-control single-open switch socket is very simple, and it can be directly connected in the process of decoration. You only need to connect the L binding post behind the socket with the red wire, and then connect to the L1 binding post with the blue wire, so that the single control single switch connection is completed.

Wiring 2: Single-open five-hole socket wiring method.

1.Switch socket installation.

When we install the switch socket, it is best to choose after the carpentry and painter have finished. In this way, it is only necessary to remove the dust and magazines in the switch socket, and then connect it so that the circuit can operate normally.

2.Power cord handling.

First, leave a small section of the wire in the switch socket box for future maintenance, and then cut the core, pay attention not to damage the core, and then tie the wire to the corresponding binding post clockwise, and then tighten the indenter, pay attention not to expose the wire core.

3.Line connections.

When connecting the line, connect the red wire (live wire) and the blue wire (neutral wire) to the terminal post L and N respectively, and the yellow-green two-color wire is connected to the socket terminal post N, and then connect the socket L binding post and the switch terminal post with a broken wire, and then connect to the switch terminal L with another wire from the bulb.

4.The switch socket is fixed.

When operating, first put the wire left at the bottom of the box through the plastic outlet hole, then the plastic table is close to the wall, and finally fix it on the bottom box with screws, after the fixing is completed, the switch socket hole at each position is threaded, and then the wire is pressed.

5.Socket panel fixing with switch.

In the end, just place the switch socket against the plastic table, get the orientation right, and then fix it with screws, and cover the panel.

Just follow the requirements of the specification.

This kind of motor should be 5 binding posts, not two phases, don't see two power lines on two phases. It is a single-phase dual-capacitor motor.

You look at the original wiring, it's really not clear to take a picture, I see that it is connected like this, and I draw it with a red line.

Except for the black wire in the motor itself, it should be connected to the capacitor and the centrifugal switch, as well as the power sleeve of the two cores. The rest is the connection tab method.

Generally, there is a wiring diagram on the motor nameplate, and you can check the wiring diagram on the motor nameplate to see if the original wiring corresponds to the forward rotation. I don't look like it, the motors I've touched are all connected diagonally. It may be that the wiring arrangement of the design of the manufacturer is different.

Anyway, there is a wiring diagram corresponding to the diagram on the nameplate. The connecting piece is either horizontal or vertical, and you use a line instead of a connecting piece here.

You can't go wrong with the corresponding nameplate.

There are 3 lines and the color is the same, first of all, verify what kind of line the 3 lines are. Do this regardless of whether the color is the same or not, you don't know what line it is and how you know what to pick.

3 lines, it is possible to be 1 fire 1 zero 1 control, 2 fire 1 zero, 1 fire 2 control ......Wait a minute.

So the first step is to verify the wires.

According to the figure 2 you gave, it is a double-open single-control surface-mounted panel, which should be used by two switches to control each of the two lights, then these 3 lines may be 1 live wire, the control line of two lights, use an electric pen to check which one is the live wire, and carefully touch the live wire with the remaining two wires, the light is on the control line of the light, pay attention to safety. Then the power is off, connect the live wire to the L of the switch, talk about L with the wire and get up, and the two L1s are connected to the light wires respectively.

This is the connection method of 1 fire and 2 lamp wires, if it is not 1 fire and 2 lamp wires, then it should be determined according to the actual situation.