How to wire the network cable board, how to wire the network cable

There are two types of network cable interfaces that can be connected to the network, which are as follows:

A line order standard:

The line order is white-green, green, white-orange, blue, white-blue, orange, white-brown, brown.

Criteria for b line order:

White orange, orange, white-green, blue, white-blue, green, white-brown, brown.

Among them, the orange and white lines and orange are used to send signals; The green, white and green lines are used to receive signals.

Precautions for making network cables:

1. When peeling:

Cut the end of the thread with the trimmer edge of the crimping pliers, and then put the end of the wire into the stripping knife edge, let the corner of the wire head and the baffle, slightly hold the crimping pliers and rotate slowly, let the knife edge cut the protective rubber of the twisted pair wire, and pull off the rubber.

2. When sorting:

We can know that each pair of wires is intertwined, and 8 thin wires of 4 pairs must be straightened out when making a network cable.

3. When cutting evenly:

Straighten the thread as much as possible (do not wrap it), flatten it (do not overlap), squeeze it tightly and straighten it (close in one direction), and then use crimping pliers to cut the end of the thread flat. In this way, after the twisted pair is inserted into the head, each wire can have good contact with the pins in the head to avoid poor contact.

4. At the time of suppression:

Make sure that all the wires are in place, and check the wire sequence through the crystal head, you can clamp the RJ-45 head with crimping. The RJ-45 head is then pushed from the toothless side into the crimping plier groove, at which point the pliers need to be held firmly.

There are two types of network cables: T568A and T568B, which means that if A presses into the corresponding network cable according to the above figure, if B presses into the corresponding network cable according to the following figure.

Orange White, Orange, Green White, Blue, Blue White, Green, Smoke White, Smoke, Mesh Cable Order.

The home network wiring is 586b orange white, orange, green white, blue, blue and white, green, brown white, brown.

Eight first, you can connect it according to the A line or B line, and press the network cable.

If you want to connect the network cable yourself, it is recommended that you go to the Internet to find the relevant tutorial to take a look, and then insert the corresponding position according to the color of the network cable.

That is, according to the color of the row marked with the letter b, just insert the corresponding color of the network cable.

Cross line: that is, the network cable with the line sequence of one end of the crystal head A and the other end of the crystal head line sequence of B (i.e., 1-3, 2-6 pairs of inverted). It is suitable for interconnection between computers and computer network cards, or between network devices and network devices (such as the LAN port interconnection of two routers, or the common port interconnection of two switches).

Try it a few more times and you'll be familiar with it.

The network cable panel connection is as follows:Tools Raw materials: panels with network interfaces, screws, screwdrivers, network cable pliers, network line testers.

1. Use a screwdriver to pry the gap in the panel and divide the panel into two parts.

2. Use the network cable pliers to cut off the dry skin outside the wire by three centimeters, and then card the network cable to the bayonet in order (blue, white blue, orange, white orange, green, white green, brown, white brown) after visiting the hole.

3. Next, you can use the network line tester to test it, and tie a safety knot before pulling on the panel after it is connected.

4. Next, put the screws on one side, fix it, and then put on the screws on the other side.

5. Close the lid of the panel, find the alignment point, and finally install the notch.

6. Press from the left, press from the right, and finally in the middle, of course, you can also choose to press from right to left.

In many cases, in the home decoration of Peicong, the electrician often leaves the network cable panel to the network cable installation and opening personnel, which causes a lot of inconvenience, such as some installation workers are unwilling to do extra work, which will cause unnecessary unpleasantness. So in life or work, we have to learn how to install it.

Take out the network cable socket, disassemble the panel, and observe the wiring method at the back. There are two types here, and the first one is below.

Here's the second option.

The first wiring method is relatively simple, just press the B color, insert the network cable in turn, press the back cover once and make it clip into the wire duct, so that each can be carried out.

The second is the older wiring duct, but the principle is the same, use the wallpaper blade to press the line into the wiring duct in turn.

Because the wiring color of the crystal head is generally consistent with the B color, the wiring only needs to be wired according to the B color.

Arrange the line and install it into the wall.

The network panel wiring steps are as follows:Material tools: network cables, modules, crimping covers, rolling strips, wire punching knives, wire cutters.

1. Peel off the outer skin with a wire puncher at 2cm and sort out the core of the network cable.

2. Use wire cutters to cut off the cross skeleton in the middle of the network cable (if there is no skeleton, it can be ignored).

3. Thread the network cable into the crimping cover according to the color indication of the wire position sticker, and be careful not to connect it wrongly.

4. Press the network cable of the corresponding color into the trunking according to the color indication of 568A 568B line sequence. After compression, cut off the excess with wire cutters.

5. Schematic diagram of the completion of the crimping cover.

6. Match the completed crimping cover one by one according to the digital instructions on the rubber seat of the module terminal, and press it into the terminal base forcefully.

<>8. The ear buckles on both sides are closed hard, and a crisp "click" sound is heard.

9. Then put on the cable tie, fix the network cable, and cut off the excess part of the cable tie.

10. The installation is complete.

Wiring method of the network panel:

Cut the outer skin of the network cable, you will see the various colors of the net and the sun line that are intertwined, and separate them; According to the position corresponding to each color, the net song line is embedded respectively; After embedding the network cable, use a wire puncher to cut off the excess network cable; After cutting the network cable, install the network panel into the wall and use. The network answer cherry chain panel refers to a type of wiring product that is applied to the wiring system of the workspace and is suitable for the installation of multiple types of modules. Its main function is to fix the module, protect the cable at the information exit, and play a screen-like role.