How to prevent wireless router from being rubbed to the network, and how to prevent the wireless rou

1.WPA WPA2-PSK encryption. The Internet people generally use fool cracking software, which can only crack the wireless signal encrypted by WEP; The slightly more advanced Internet Rubbing Immortals will use the packet capture tool to analyze the content of the packet, so as to crack the key to get the WEP.

But if you use WPA-PSK or WPA2-PSK encryption, unless you meet a top hacker and give him ten days and half a month, no one will be able to get into your net under other circumstances. This is currently the most effective way to put an end to the net! The setup method is also very simple, just go to the wireless settings, change the encryption mode to WPA-PSK, and then enter the key and it's OK.

However, this method has a drawback, which is that it will reduce the performance of the wireless network slightly.

2.Added MAC address filtering. Under the wireless settings or fixed DHCP settings of wireless routing (the location of this function varies depending on the route), there is a function for MAC filtering, which is used to organize or allow computers with corresponding MAC addresses to access.

Each computer's network card has a unique address called MAC address, we only need to allow our own computer to access, other computers cannot, to achieve the purpose of preventing rubbing the network. All you need to do is add the allowed MAC addresses in the settings.

3.Modify the internal IP settings (optional). If you don't feel safe enough, then you can go ahead and set it up.

First, turn off the DHCP service. DHCP can automatically assign IP to the wireless network, which also makes it easier for the Internet users to access your router after cracking your key. After turning off DHCP, your computer's wireless network card needs to be manually assigned to the IP, don't worry, let's change the internal IP of the router first.

Generally, the default IP address of the router is the gateway address, and we change the address to any intranet address, for example, so that the internal computer can specify the IP as the network segment.

If you don't broadcast, the computer manually adds, DHCP is not enabled, you specify it manually, and the routing IP address is changed. ]

Set your own password, and others won't be able to access the Internet].

1. Check whether the router has been rubbed against the network, you can open the browser to enter, press enter, and then enter the user of your router, as well as the password to log in, and check whether there is an unfamiliar device in the corresponding menu, and the IP is inconsistent with the hardware, and it will be rubbed against the network.

2. Let the router speed adjustment liquid system be maximized, the router factory setting is 75% rate, and you can enter the safety setting to maximize the rate modulation of the router.

3. The location of the router is not very good, such as the corner of the wall and the dense place of items, which are the root causes of the signal quality.

<> wireless routers send signals across the board, and the closer the router is to obstacles, the more easily the signal is suppressed. Therefore, you should choose a high and spacious location in your home to place the router so that the signal can radiate downwards and reduce the blocking of obstacles and signal blind spots.

Routers transmit data information in the form of data packets. Electrical appliances, glass, and metal items will cause obvious interference to the signal, resulting in transmission blockage. Friends can keep the router away from the above categories of items to reduce interference.

1. If the router version is older, then regularly updating the firmware can ensure that the software of the router is in a good and efficient operating state.

2. If the wireless router at home has been used for too long, it will be a good choice to replace it with a new dual-antenna or multi-antenna router.

1. Buy a wifi repeater: plug the repeater into the socket at home, and the signal range and strength can be enhanced after debugging.

2. Reuse of old routers: Set the old router to AP mode, and then connect to the existing main router through the LAN port to expand the signal.

3. Adjust the antenna: Most router antennas are placed in a "ring", and in the vertical direction, the signal coverage will be wider. The antenna can be adjusted appropriately according to the distance and angle.

Usually the router is factory set to mixed mode with a set rate of 75%.

1. Adjust the rate: The partner can enter the security settings and adjust the rate of the router to the maximum.

2. Select Single Protocol: Set the mode to use only protocol.

Open the browser, enter the router address and username and password, check whether there is an unfamiliar device in the corresponding menu, and compare the IP address with your own hardware.

Then send the friends three magic weapons to prevent rubbing the net.

1. Set a complex password.

In the Tab or Security, select the WPA-PSK WPA2-PSK password and set a complex, easy-to-remember, and hard-to-guess password.

2. Disable the DHCP function.

In the Local Area Network (LAN) settings, disable the DHCP function to prevent automatic IP address assignment to wireless clients.

3. Change the default IP address.

If it defaults, it can be changed to prevent easy guessing.

1. Set a more complex password. Many users like to set the wifi password to their own easy-to-remember password, which is generally set in a purely numeric way, which is easy to be cracked by wifi password cracking software, so as to rub your home network. Therefore, the wifi secret or code should be set more complicated, and it is best to use a combination of numbers and English letters, so that the security will be higher.

2. Hide WiFi signal. After the computer and router are connected, enter the router settings page, select "Wireless Settings", then change the router wireless settings, and unenable SSID broadcasting" check, so that the router will not broadcast the wireless name, and others will not be able to see your router name.

3. Do not use wifi cracking software to connect. Nowadays, many people like to use wifi cracking software to connect to wifi, if you connect to wifi like this, even if your password is complicated, the software will record and send it back to your cloud server through your wifi network.

4. Bind the MAC address of the Internet device. You can bind the MAC address of the Internet device, so that you can only bind the machine in the router to access the Internet, and other machines can not rub the network even if they get the wifi password.