The computer can t enter the system, and I am desperate to get a finger on it!

That's a strange question. I guess it's not a bit of a problem with the hardware, but the hardware is not necessarily a problem with the settings, there may be some electronic components that fail (but not completely fail, and occasionally play a normal role), resulting in when these originals are in normal you can go in, and use normally, the next time you want to go in, it depends on luck.

To put it bluntly, computer accessories are still a collection of physics-based electronic devices, and damage or probability of failure of any of the original components in them can lead to various problems.

The above is a personal analysis for your reference.

If anything, let's talk about the news.

I've also had questions like yours, and there are a few possibilities.

1》Is your hard drive cable damaged, try a different strip.

2》Your hard disk jumper is not set up,If your optical drive and hard disk are on the same data line,You only install the hard disk to try to get in,4》Your motherboard hard disk die interface failure,Change the ATA interface of the hard disk to try it;

Good luck!!

Probably a memory issue! It is recommended to try a different root.

Your memory is dual-channel because you changed the card slot. I suggest you switch to another motherboard to see if there are any problems with the memory. If there is no problem inside, it may be a problem with the motherboard. If there is a problem, take it to a professional repair shop for repair or replacement.

This is a problem with the disks, please fix it (fix each disk or only fix the e prompted).

Built-in disk repair method:

The specific steps are as follows: select the drive letter in my computer, right-click to select the properties, select "Tools Start Checking" in the pop-up drive properties window, and select "Automatically repair file system errors" and "Scan and recover bad sectors", and then click Start, the scanning time will vary depending on the disk capacity and scanning options (after doing it according to the above method, a box will pop up, the point is, repair after automatic shutdown at boot, win7 select the disk check button according to the plan).

Bad sectors on the hard drive will lead to corruption or loss of computer system files, computer failure to boot or freeze. Hard disk bad sectors can be repaired using NDD Disk Utility or Scandisk.

If the fault persists, please restore the system or reinstall it (it is still not possible to format the hard disk and repartition and reinstall it, if it doesn't work, you will have to replace the hard disk, or overhaul it).

Find a way to enter the system to repair the disk, enter, wait a while to try, boot and press F8 to select safe mode, PE, reinstall the system, and go to the repair there to help you.

This is the percentage of completion of the boot self-test program running on the bottom line.

If you can't get in all the time, it is recommended to test the hard disk and possibly the hard disk bad sectors.

What should I do if the computer can't enter the system when it is turned on, Brother Ming teaches you that you only need a USB flash drive to solve it.

360 is quite professional.

However, the solution is to reinstall the system.

It's safer for you to find someone to reload yourself.

Enter the PE low-level hard disk reinstallation system.

The best thing to do is to go to the place where you bought the computer and solve it directly and efficiently.

It may be that your hard drive is broken, check it with PE.

If you have a disc installed, use the disc to start and fix it.

The steps are as follows. Boot BCD appears at boot, prompt.

1.BIOS is set to optical drive boot, then put the Windows 7 installation disk into the optical drive, and then boot the computer.

2.Press any key when prompted.

3.Select a language, time, currency, keyboard, or input method, and then click Next.

4.Click "Repair Computer".

5.Click on the operating system you want to repair, and then click Next.

6.In the System Recovery Options dialog box, click Command Prompt.

7.Type , and then press Enter.

8.Enter the following commands:

bcdedit /export c:\bcd_backup• c:• cd boot• attrib bcd -s -h -r• ren c:

boot\bcd bootrec /rebuildbcd

Reboot, and then change the BIOS back to hard disk boot, just boot normally

If you start it, make sure there is no disc in the drive.

If not, go into the BIOS and set the boot mode to hard disk boot. Reboot again and try.

If it doesn't work again, find a win7 system installation disk, and repair the system.

The last resort is to reinstall the system.

The display shows that there is no signal again, so is your console still running?

Is the monitor cable loose, enter PE to disinfect, and then restart.

How to solve the problem that the computer can't enter the system.