How to change the font library for your phone? What s the Font Driver?

Self-signature required) I will upload it in the attachment below, and I personally recommend that it is best to install the font driver on the C disk (that is, the phone's own memory), so that it will be more convenient to have a black screen at boot or change the font. (2) Copy or move the font file to the e:data fonts directory with X Manager, as shown in the figure (if there is no fonts folder, create one yourself).

It can also be placed under the C drive! But the memory that comes with the small i is too small,The font is generally relatively large nearly 10m or so,So it's better to put it in the E disk (memory card),But if you unplug the card in the boot state for too long, there will be an error report,Don't be nervous,Just plug in the card,And if someone sends a text message or hits ** when you unplug the card,The words displayed will not be complete,A little flaw is still understandable! (3) Restart, and then you will see the font you want on your phone.

Install the font driver first (to be installed on the E disk), and then move the font file (TTF format) to the Data Fonts folder of the C drive or E disk, and then restart the phone. (Font drivers and font files can be found on the Symbian Mobile Forum**.)

1. Disassembly, because the chips are on the motherboard, and if you want to take out the motherboard, disassembling is the first step that must go through Shanbu. (Operated by general engineers).

2. Clear Li to remove glue, the font library on the motherboard of the original machine has glue, as you can see from the above, then you need to use a heat gun to heat, and then remove the glue little by little. (Senior engineers can operate, and a fairly accurate grasp of temperature is required).

3. Disassemble the font library, and after heating to a certain extent, use a tool to remove the font chip. (Senior engineers can operate, and need to have a fairly accurate grasp of the temperature, time and strength of the font).

4. In addition to the glue, what needs to be removed here is the glue remaining at the bottom of the font and on the motherboard. (Senior engineers can operate, and need to have a fairly accurate grasp of temperature and strength).

5. Install the new font, just like the CPU of the computer, the back of the font also has a tin point similar to the pins and the corresponding pins, you need to find the right direction and position when installing, and there is no way to use it, this process also needs to be operated by air gun heating (senior engineers can operate, and you need to have a fairly accurate grasp of temperature, time and strength). After the installation of the new font library is completed, it does not mean that the repair is completed, at this time, the mobile phone can be turned on, and the SIM card can also be read, but there is still no signal in the top status bar, and the first four digits of the serial number that appear in the dial keypad input * are 0049 (engineering mode serial number), at this time, it is also necessary to repair the signal and write the serial number.

6. Use SPT equipment to write serial numbers and repair signals. SPT mode and factory mode are two different engineering modes built into the phone, SPT mode is used to repair the signal, and factory mode is used to write serial numbers.

I can't turn it on.,It's good to just be hard-wired.,The disadvantage is that there's no backup.,There's nothing.。 I just got the grid machine the morning before yesterday.,It's also starting to appear the word nokia.,But it's stuck there for a while.,Can't get out of the hand-holding picture.,The grid machine will be fine.。

1) Soft grid: Enter * on the mobile phone, the way to restore factory settings, which is the so-called soft grid machine, the grid machine can restore all the original settings, empty all the contents of the c: disk, and then write new system information, the grid machine will not affect the factory content on the e disk, but the software you installed on the e disk can not be used;

2) Hard grid: Shut down first, press and hold the "dial key, "* key and "3" key" while rebooting until the word "nokia" appears on the screen (the new v31 version will not be displayed), this process can not release any button, wait for a few seconds until "formating...... appears", then you can release the key. 3 After 5 minutes, the system format is completed, the phone will automatically restart and enter the standby screen, and then re-enter the phone time.

Because you can't turn on the machine, so hard grid,My 5730xm,Loaded Huakang girl font,Personal experience。

Is the file name of the font file in Chinese? Chinese cannot be read, only English or digital Otherwise, there will be a black screen on boot If you can't turn on now, you can take out the memory card, use the card reader to connect to the computer, and then go to the data fonts bar to modify the font file name

Professional Answers! What you said is that when installing the font driver, the system prompts that the application is not compatible with the mobile phone,It is very clear to tell you that it is not a problem here,Basically, the mobile phone will have this kind of prompt when the software is arranged!!

Also, my font driver is installed on the C drive, and the font files are installed on the memory card! Try it yourself!

Also, it is not ruled out that there is a problem with your font driver, please re-create a font driver!!

Don't worry! Minor problem !! Let's start with a hard grid! If not, look it up online! Because I don't know if your model is not good, teach you how to tough! Hopefully you'll be tough yourself!!

Of course, incompatibility causes conflicts. Uninstall fonts. I can't uninstall and I have to format the card.