The data file MS in the D disk has been checked by me, how to recover

FinalData or EasyRecovery seem to be useful, but if it's **, it's ......

As long as you still want to recover, don't write "hard disk".

finaldata：

easyrecovery

It's OK in the U disk, because your partition has been deleted, so you shouldn't recover by partition when recovering, but you should use disk recovery (the second item) as long as you choose the right range of documents, the recovery probability of the document is much higher than ***, and finaldata can also repair office documents.

I can tell you very sadly, probably your data will not be recovered, as long as it is formatted and relies on us non-professional people, it is difficult to recover!

The only hope is that you take your disk to the computer city to find a professional to recover, but it seems that the fee is very expensive, about 300 yuan.

Infinite sympathy.

It's over, really. Finished.

Take your hard drive to a data recovery company (charged per byte) for about 1500rmb....

That's the way to go!

If you want to recover data, the first thing is not to write any files to the hard disk, turn off all unnecessary processes, use easyrecover, the effect is okay, and you can get back some files.

easyrecovery

But if you've ever manipulated this partition after formatting, there's not much hope.

easyrecovery

professional

This software can retrieve files that have been formatted, deleted, etc. I've used it, it's still good, you can try it too.

However, it is best not to copy files to the formatted D drive before retrieving them, as they may not be recovered.

It is necessary to remind everyone to stop writing data to the hard disk immediately after the hard disk is formatted to prevent the accidentally deleted data from being overwritten by new data, which will affect the later recovery work;

I suggest you try it like this:

2.After installation, double-click to run to enter the software operation interface, then click on the function selection bar on the left side of the interface to select "Formatted Recovery", and click the "Start Recovery" option on the right side of the interface after selecting the function.

3.After selection, on the disk selection page that jumps to the jump, double-click to select the disk that was formatted by mistake, select drive D here, and then click "Yes" in the pop-up confirmation selection box to confirm the selection.

4.After selecting the disk, the software will scan the selected disk, find the files you want to recover in the file directory bar on the left side of the scanning interface, and then click to check, confirm the files and click "Recover" in the lower right corner of the interface

5.Click "Select Directory" to customize the save path of the file after recovery, and click "OK" to start restoring the file.

6.Wait patiently for the file recovery to complete, and then view the recovered files under the path you set.

Answer: Pro, this situation depends on the version of the recovery tool software and the degree of formatting of the hard drive. The professional version of the data recovery software recovers 80% of the data for thousands of dollars60% of the regular version20% of the cracked version on the market.

Q: Can you help me recover?

Answer pro,Remote is not recoverable,The professional version is to lock a computer host,Use it to recover the removed hard disk hooked in,And then through the data recovery software to find the data in the secondary disk,The time is very long,It often takes about 1-2 days。

Question: Remotely can't be recovered?

Question: I'm from Liyang, Jiangsu, I don't know which computer companies in the local area can get it?

diskgenius Chinese Simplified Chinese Edition is an expert hard drive bad sector repair tool with high technology and comprehensive features. DiskGenius free version imitates Windows pure Chinese graphical interface, supports mouse operation, Diskgenius hard disk bad sector repair tool is more flexible partition operation than fdisk, powerful partition reconstruction function.

If the computer D drive is simply formatted, the data can be read back through professional recovery software. The degree of data restoration depends on the actual situation, generally if there is no new data written to overwrite after formatting, this recovery rate can reach 100.

2. After that, select the D disk to be restored for recovery;

3. Finally, wait for the scan to recover.

Therefore, it is recommended that no data be written into the D drive after it is formatted, after all, it will be difficult to recover the source file once it is overwritten.

The D drive is formatted, you can retrieve the data lost due to formatting according to the following methods:

Tool Required: Data recovery software.

Steps:1Install the data recovery software on your computer and run the software. Note: The software cannot be installed on the D drive, otherwise it will cause further data destruction.

2.Select the features that are suitable for formatted recovery. Note: Select the correct recovery module to perform targeted scanning.

3.Select the formatted drive and click on the "Next" button to start scanning the files.

4.After the scan is completed, you can preview and filter the listed files, so that you can find the files you want to recover in a relatively short time.

5.Put a tick in front of the files you want to recover and click on the "Recover" button so that you can copy the files out.

6.Set a destination folder and save the recovered files. Idea: The destination folder cannot be set to the D drive, otherwise the lost files will be overwritten.

Note: Data recovery is not a one-size-fits-all method, and there is no guarantee that it can be 100% recovered in any situation, because there is no way to recover the overwritten files. If the D drive is formatted by mistake, it is forbidden to write data to the D drive, otherwise the lost files will be overwritten and the files cannot be recovered.

Steps to recover formatted D drive:

2. Open the software recovery, and all partitions and physical disks will be listed automatically. We need to select the D drive to start scanning the recovery;

3. The software will quickly find out the data of the D drive, and list the root directory of the D drive, we double-click to see the specific directory structure;

4. Check all files - right-click to copy the files;

5. Save the file to a suitable path;

6. Finally, wait for the software to copy the file.

Computer formatting is also a time that we often encounter, after formatting, how to retrieve data? In fact, the data can still be retrieved after the computer is formatted, so follow the method to try it.

You can try to recover it with data recovery software, but don't get your hopes up!

How to recover data if the computer D drive is accidentally formatted? It is recommended not to read and input new data into it at the first time of sleepiness, you can try to use some data recovery software to recover overwritten files. Here are some data recovery tools that may be useful:

The specific operation demonstration process is as follows:

1. Open the software interface and click on the function setting option that needs to be restored.

2. Find the original storage location of the lost files, confirm that they are correct, and click the Start Scan function button.

<>4. After the file progress bar is successfully restored, click the "Open" button to view the successfully recovered files.

Note that the success rate of recovering files depends on a variety of factors, such as file size, storage device type, and how long the files were overwritten. Therefore, if you want to maximize your chances of a successful recovery, it is recommended that you stop using the device as soon as possible and carefully read the instructions for use of the recovery software before attempting to recover your files.

3. Select the disk formatted by mistake, click the corresponding disk, and then click "Next" to enter the scanning process. When the scan starts, the software will automatically analyze the data of the malformatted hard disk in depth, without any manipulation.

4. After the scan is completed, you can directly select the formatted data that needs to be carefully recovered on the software result page, check it, and click "Next" to complete the whole process.