SATA dual hard disk problem, there are two SATA hard disks, how to set up dual hard disks

Any brand of hard drive will do.

Install it in your computer and plug in the power and data cables.

After installation, start the computer, go to the control panel, go to the management tool and select computer management, disk management.

Then press the text to partition and format the new hard disk.

The P5GPL uses a 915PL chip, which should be able to support hard drives up to 2T. First of all, you have to buy 500G or 1T, you can't set up RAID. If you want to do RAID, then you need to require the capacity to be exactly the same size as the original hard drive, that is to say, you have to buy another one or n 160G.

Regarding partitioning, or if you don't do RAID, then you can plug it in (pay attention to the boot order) and use it, and directly use the system's built-in "disk management" (my Vista is called so), and you can partition. You can also use the ability to extend volumes.

Ten is only enough for your first few problems, your motherboard supports large hard disks is no problem, and the installation is very simple, just buy a data cable and a power adapter cable. There is no need to buy the brand's products, even if they are the same brand, there are incompatibility situations. I'll do the last question too, but I'll be fine if it's too much trouble.

There is no limit to the brand of hard drive, as long as the interface is enough, you can buy one of the commonly used brands and connect it.

There is no limit to the capacity, as long as there is a corresponding interface on the motherboard.

The motherboard does not identify the hard drive with a brand. Only interface issues and capacity issues of the drive are identified.

1. Enter the BIOS.

2. Enter the first item in the diagram above, intergrated peripheralsThe first record: on-chip IDE channel, enabled, enabled. Set it up according to your specific situation.

3. Then make the following settings.

4、hard disk boot priority.Hard disk boot order. Make the 160GB Hitachi hard drive the first hard drive to boot.

5. I saw two hard disks:. Hitachi, 160GB, main disk. , Easy Extension, 80GB, slave disk.

Nowadays, many ghost systems move "My Documents" to drive D, when there are 2 SATA hard disks, the first partition of the slave disk will be mounted as drive D, that is, for example:

It turns out that a hard disk has no problem entering the system, a single hard disk has C, D, E partitions, and the second hard disk becomes C, E, F, from the first partition of the disk to the D partition, the system cannot read the configuration information in "My Documents" (my documents are in the E disk), which will lead to the inability to enter the system.

Usually it's a system issue or a hardware issue with your hard drive.

1. Reinstall the system, because XP itself does not support SATA hard disk, it is best to install the system above win7, you can identify it;

2. No matter what system is installed, it is best to install it with Microsoft's original CD, or install it using the U disk installation method, and try not to use the ghost installation method, because the ghost images are made by individuals and have defects;

3. If none of the above methods work, generally the hard disk itself has a hardware failure, detect the health of the computer, if there is a yellow or red warning, it is a hardware problem, consider changing the disk.

With the gradual increase in the amount of data stored in my computer, my previous computer was seriously short of hard disk space, so I bought a new hard drive. However, after working two hard drives together, problems such as crashes and slow running speed often occur. After checking a lot of information, I finally determined that it was a problem with the setting of the master-slave disk.

1. Distinguish the type of hard disk

Before reading this article, you must first learn to distinguish between hard drives. Hard drives for home use are generally divided into two categories: IDE and SATA. The most obvious between them'The difference is that the interfaces are different, and the data and power cables used are significantly different.

Old computers generally use IDE hard disks, and the data cables used are serial ports.

New computers generally use SATA hard drives, and the data cables used are obviously different from IDE hard drives, so they can be easily distinguished by the data cables.

Second, the hard disk master and slave setting method

IDE disks are distinguished by jumpers, as shown in the following figure.

The specific setting method, the hard disk produced by different manufacturers is slightly different, please check the instructions on the hard disk for details.

The master-slave setting of SATA hard disk does not need to set up a jumper, which is mainly determined by the data cable interface on the computer motherboard. Please carefully check the description of each interface, the interface of SATA1 can be connected to the main hard disk, and other ports can be inserted from the disk and optical drive.

The author's computer uses two SATA hard disks, and after inserting the main disk into SATA1, the computer boot speed has become significantly faster, from 3 minutes to 50 seconds, and the most important thing is that there has never been a crash again. I hope this article can help everyone.

The speed of the startup speed is not only related to what you say, but also related to your hardware settings

1. See what mode the hard disk is in the self-test, DMA mode is normal, PIO mode is extremely slow. If it's PIO mode, please go to the BIOS and load the default value, and then turn it on to see, it should be changed back to DMA.

2. Check whether the optical drive is connected to the slave disk. If it is, it will slow down the boot speed significantly. This is because the system detects the master disk and then the slave disk when it starts, and if the master disk is empty, it will take a few seconds here.

Please turn off the device and connect the optical drive back to the main disk. You can also use the hardware without moving, that is, you can set the main disk to "none" in the IDE attribute where the optical drive is located. Some optical drives are set in the slave tray when they leave the factory, if you have never paid attention to it, then please pay attention to it now!

3. The hard disk (parallel port) should use an 80-core data cable, and do not use a 40-core optical drive cable instead. The speed of the optical drive line can only reach DMA33, while the speed of the hard disk can reach DMA100 or DMA133.

4. The new generation of motherboards has added SATA hard disk interface. The user's hard disk is generally only one. This means that there will always be an IDE port or SATA port that is idle.

The system detects each hard drive interface every time it is turned on. If there is no interface to connect the device, it will take a few seconds to detect. So this kind of motherboard starts to roll the scroll bar a few more times (such as intel

865 and later motherboards). We should close idle IDE or SATA channels in the Device Manager. At start-up, it can reach the ideal state of rolling one and a half times. If your drive is a high-speed, high-density** drive, the progress bar will pass in less than one lap.