How many types of 360 router P2 have?

Two ways: connect the network cable from the LAN port of the primary router (A) to the WAN port of the secondary router (B).

The network cable that comes out of the LAN port of Router A connects to the LAN port of Router B.

First method:

The network connection mode of router B should use static IP, and the IP address should be on the same network as the LAN address of router A, such as the LAN address of router A, the WAN address of router B can be used, and the subnet mask is as follows: , gateway and DNS address of router B

The second method:

The LAN address of router B can be different from router A, but in the same network, the same IP address can be set as above. Wireless can be set to use different frequency bands to avoid interference.

This ensures that all terminals can access each other.

The 360 mobile phone software does not support your router, it is recommended to use a browser to enter the router. Access to the router method: Method 1:

admin, password: admin. .

The most fundamental difference between P1 and P2 is that P2 is an AC dual-band route, with a general access bandwidth of more than 50 megabytes, and 5G is the first choice. P1 is a single-frequency route, and if you don't have a device at home that supports 5G hotspots, single-frequency routing is more cost-effective.

Hello, this is the parameter of the 360 security router P2:

A working wireless router is to have a wifi signal light and a stool Zheng Chang working network Zaoyuan Song connection light If you encounter this split reed problem again, you can reconnect the network cable and restart the router.

Hello, this should be normal, you can surf the Internet normally.

January 12, 2016 10 a.m.

360** Rush to buy.

Hello friends suggest paying more attention to the official website of the 360 router, there will be a prompt when it is released.

1. Open the router and plug the original cable of the broadband into the computer directly into the WAN port of the router (see the manual); Find another network cable to plug in the LAN port at one end (marked on the router) and plug in the desktop computer at the other end;

2. Turn on your computer, open the IE browser, enter: pop up the login page, enter the admin password admin (read the manual or) or other.

4. Enter the broadband and password (if you don't know, call broadband customer service); Next, 5. Ask you if you want to turn on the wireless network, and select Turn it on; Security options, you can choose one: wpa-psk wpa2-psk, enter the key, the rest are automatic, if you understand, read the manual. Save the restart route, 6, at this time the desktop has been able to wired Internet access, and then open the wireless network card in the right corner of the desktop to right-click to view the available wireless network, now your router broadcasts the signal, double-click to connect, enter the key to get it.

Wired and wireless access is available.

After the router is successfully set up, the broadband dial-up of the original computer desktop does not need to be clicked, and the IE can be accessed directly by opening the IE.

The 360 router P2 is better, this router has many functions and supports 5G.

Of course, it's P2 dual band, as long as your phone supports it, but ** slightly expensive.

How many wireless access devices the router can tow has nothing to do with the bandwidth of the broadband, but with the load of the router.

If the load is ignored, a single router can be connected to 254 settings.

Hello Friends, Friends can theoretically connect 253 of them.

Household in general.

1. One end of the network cable is connected to the WAN port of the router, and the other end is connected to the LAN port of the cat;

Then connect the LAN port and computer network port of the router at both ends of the network cable.

2. Open the browser, enter the IP address of the router), enter the router account and password (see the label or manual on the router box).

3. Click [Setup Wizard] after entering the router setup interface, and click [Next] after entering the setup wizard.

4. Select PPPoE (ADSL Virtual Dialing) and click Next.

5. Enter the Internet account and password, confirm the password, and click [Next].

6. Then wireless settings - basic settings, enter the SSID number, that is, the wireless device name.

Channel: Select 1 or 6 or 9 (if connected to an Apple mobile device or Mac: select 11 or 13);

Note: Because channel 1 or channel 6 or 9 has minimal interference, and because Apple mobile devices or macs support high-band channels, 11 or 13 is selected.

Click the Save button.

7. Then select Wireless Security Settings, select a WiFi encryption type, enter the WiFi password, and click Save.

8. After the setting is completed, one end of the network cable is connected to the LAN port of the modem, and the other end is connected to the WAN port of the wireless router.

The signal of the 360 security router is good and has strong ability to penetrate walls, so it is safe to use.