Where are the events during the May Day period for Breitling watch repairs?

How to deal with water ingress into the watch:

If you accidentally get water inside your case, you can use a granular substance called silicone to put it in a meter-closed container with the watch that has accumulated water, and after a few hours, you can remove your watch and the water will disappear. This method is simple, convenient and economical, and does not compromise the accuracy or longevity of the watch. In addition, the silica gel that has absorbed water many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

Second, the secret of refurbishment of the watch with water ingress. If your watch is scratched with a lot of lines, you can drop one or two drops of water on the watch mask, and then squeeze a little toothpaste to wipe it, you can remove the scratches and make the watch mask as new.

Third, the maintenance secrets of the watch when water enters. When wearing a watch, the sweat on the hands is corrosive to the case, the all-steel case is nickel-chromium alloy, the corrosion resistance is better, and the semi-steel case is copper, which is in contact with sweat for a long time and is easy to corrode, so you should often wipe off the sweat with a soft cloth or put on a plastic watch holder to prevent it from being eroded by sweat. Do not open the back cover of the watch at will, so as not to let dust enter the movement and affect the normal operation of the watch, thereby shortening the life of the watch.

Do not leave the watch in a closet with mothballs to avoid deterioration of the watch oil. Do not place the watch on the radio, TV to avoid magnetization. Watches that are not worn for a long time should be wound regularly once a month so that the parts will not be in a stationary state for a long time, so as to ensure the operation performance of the watch machine.

Shanghai Breitling watches.

It is recommended that the watch need to be thoroughly serviced every 2-3 years.

The frequency of maintenance of a watch depends on the model of the watch, the climatic conditions and the daily maintenance of the owner.

Most watch lovers would normally advocate that their watch be returned to the service center for service every three years. But it depends on the situation, in addition to waterproof, it is also necessary to prevent collisions.

On a scale that can only be afforded, it is not harmful to have two or three watches swapped in daily life: wearing a mechanical watch during dynamic movement, such as improvising over time, can help extend the service life of the watch.

1. The watch that is worn every day, it can also be said that the watch does not leave the hand for 365 days, if you find that the error of the watch is very large, or the watch is water, it is best to send it for repair and maintenance; If everything is fine with your watch, it's best to have it serviced every three to five years; Some people's watches do not leave their hands, a wear is more than 10 years, this is not the way to wait for the watch, because of long-term use, the lubricating oil of the watch will still be lost or dried up, in the case of oil loss, it will accelerate the wear of the shaft; There are quartz particles in the air that we can't see with the naked eye, which will adhere to the oil, and if you don't maintain it for a long time, and let the watch keep going, it will only accelerate the wear and tear of the shaft; Some people wear it for 10 or 20 years, and the watch will go when they never want to maintain it, and when it fails, many parts have been seriously worn, and after maintenance, its accuracy will be greatly reduced, which is not as good as a new watch.

Second, if you don't wear it often, you can't wear it twice a month on average, and it is recommended that it should be repaired in 5 or 10 years.

Just as a car requires regular maintenance, Breitling watches need to be carefully maintained to maintain their splendor and precision over time. Depending on the mechanical characteristics of the watch, Breitling watches need to be serviced every 1 to 5 years. It is common for mechanical watches to be serviced every 3 years.

1. Disassemble the strap: It is not necessary to remove the strap, but it can be more convenient to replace the battery. If there is an arrow pointing on the reverse side of the strap, follow the arrow to fix the strap on the meter splitter, and slowly rotate the handle to push out the shaft of the strap.

The thimble of the meter dismancer cannot completely push out the shaft, so you need to pull it out again. When you put the shaft of the watch strap back on, you have to go in the opposite direction. Note that the two ends of the shaft are different, one end is round and smooth, and the other end is slotted screw-shaped.

2. Clean your watch. Although the size of the watch is small, the internal structure is indeed very complex and precise, and a little dust or clothing fiber will affect the timekeeping of the watch. Therefore, before replacing the battery, the bottom cover of the watch should be cleaned as if it were a surgical operation, and the bottom cover should be opened and the gap between the bottom cover should be vacuumed.

3. Remove the back cover: Adjust the two-foot cover opening tool, fix it in the groove of the back cover of the watch, and rotate it counterclockwise to open it. There are generally two fastening methods for the back cover of the watch, one is to fasten the screw, the other is to clamp the tight scene, and the other is with a collapse, which is relatively rare.

Those fastened with screws can be unscrewed with a special wrench or instrument caliper; As for the second type, it is relatively simple, use the tip of the steel plate knife along the gap of the back cover of the watch to gently "squeeze", such a cover generally has a small platform behind the cover, after the tip of the knife is sewn in, it can be gently prying.

4. Take out the battery with tweezers: use bamboo or plastic tweezers to take the battery, remember to wear gloves when taking the battery, so as to prevent static electricity on people's hands and avoid causing a short circuit in the battery.

5. Clean the battery: Before installing a new battery, check the positive and negative connections connected to the battery.

6. Replace the original battery. You should try to choose the original brand or origin battery. Finger sleeves should be worn when replacing the battery to avoid the sweat on the fingers from polluting the machine core, which will corrode the machine core and can never be removed.

7. Check the waterproof accessories. The waterproof accessories of the watch are generally rubber or plastic materials, and the waterproof accessories will lose their waterproof performance after aging. If the waterproof accessories are aged, they must be replaced, otherwise the watch will enter the water or vapor, causing the movement to oxidize and rust, causing irreparable failure.

9. Test waterproof. In order to ensure the stability of the movement, it is necessary to ensure that the case protects the movement, the most important of which is the waterproofness.

Recommendations for the use of mechanical watches:

1. Watches with manual winding movements should be wound at the same time every day as far as possible so that the watch has enough energy to operate in the next 24 hours.

2. The energy of the watch with automatic movement is ** in the movement of the wearer's arm, so there is no need to manually wind it under normal wearing, only when the wearer's exercise is not enough to replenish enough energy to the mainspring, it can be compensated by manual winding, and the crown rotation is controlled within 20 laps when winding.

3. For a self-winding watch that has not been worn for more than 40 hours, the crown should be turned 20 times to reactivate the movement when worn again.

4. In order to prevent moisture from penetrating into the case and maintain the waterproof performance of the watch, please make sure that the crown is locked at all times.

If there is a problem with the watch, call the customer service first, and the customer service in Guangzhou can try to call the 29872673Remember to add the area code of Guangzhou in front. Then the customer service will tell you how to go after the sale. To the after-sales inspection and maintenance, just follow the process.

Use a knife to pry open the back cover, see what model the battery is, and go buy the same model and come back and replace it.

You can take it to a regular watch repair center for maintenance, and in Nanchang, you can take it to the downtown area to see the second floor of the southern section of Times Square, Shengli Road, Donghu District.

The cleaning and lubricating of watch movements, referred to as "oil washing", is a very important task in watch repair. The purpose of oil washing is to insist on the cleanliness of the watch parts and the necessary lubrication of the parts, so as to ensure the precision of the watch parts, improve the accuracy of the watch machine and extend the service life of the watch machine. Under normal circumstances, the general meter machine is used for two years and then the oil is washed once.

Under normal circumstances, the washing work is often carried out at the same time as the adjustment and repair of parts. In addition, while checking the failure of the meter machine, it is necessary to wash the oil of the meter machine when the following problems are found:

1. The lubricating oil in the movement is dry or sticky. This will increase the resistance of the movement of the mechanism, so that the watch machine is not accurate.

Second, there is too much lubricating oil in the meter machine. This will cause oil to overflow everywhere and contaminate the parts, especially the escapement speed regulating mechanism, so that the watch machine will stop or be obviously inaccurate.

3. Foreign matter enters the movement, such as dust particles, metal particles, fiber fines, etc. This will cause the transmission mechanism of the meter machine to be blocked, so that the meter machine is not accurate or even stopped.

Fourth, the parts are rusty.

Nanchang Times Square Longines store on the second floor of Guangcheng watch repair center can be maintained.

Hello, glad to answer for you!

Room 601, Block B, New World Office Building, No. 3-5 Chongwenmenwai Street, Dongcheng District, Beijing] [010-59504813].

Reasons for inaccurate time:

The watch's kinetic energy reserve is insufficient

The watch is affected by a magnetic field

The watch has been hit or struck by an outsider

The watch has not been maintained for a long time

The watch battery is low.

If the watch is faulty, you can call for consultation**!

What to do if the watch gets water.

It is normal for the watch to get water, if the water is not serious, but there is a layer of fog in the watch glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it for about 30 minutes at a distance of 15 cm from a 40-watt light bulb to eliminate water vapor. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours.

Of course, there are also some daily repair methods for watches to get into the water:

1. Dry the granules with silica gel. If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

2. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

3. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe.

4. Send the watch shop to wipe the oil. None of the above three methods can remove water vapor, so you should immediately send it to a watch shop to wipe the oil to remove the moisture from the movement to avoid rust on the parts.

5. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

6. Dry with a hair dryer, the temperature should not be too high, the wind is mild, and you know that you can't see the moisture on the glass.

If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts. Remember not to disassemble the movement yourself, so as not to damage the movement, and then repair it will be more time-consuming, laborious and costly.

1. Anti-magnetic demagnetization.

The metal material of the watch is very easy to be magnetized and cause the watch to malfunction, so try to avoid placing the watch next to magnetic objects, such as mobile phones, computers, magnets, metal buckles of bags, car door handles, automatic mahjong machines, etc. Once the watch is magnetized, it will cause inaccurate time, it is recommended that you send the watch to a professional luxury repair and maintenance center for demagnetization as soon as possible.

2. Prevent collisions.

No matter how good the quality of the watch is, it is composed of a sophisticated movement, and a collision can easily cause mechanical damage and scratches on the appearance of the watch. It is recommended that when you wear a watch, you must try to avoid the watch being collided, and if the watch is damaged by the collision, it must be sent to a professional luxury maintenance center for professional repair and maintenance in time.

After 2-3 years of use, the waterproof rubber ring of the watch will deteriorate, which may lead to water ingress problems. It is recommended to conduct a waterproof performance test once a year and replace the waterproof gasket in time to avoid water ingress. Try not to use the watch often in hot and humid or extreme environments, so as not to cause water problems in the watch.

When using the watch in normal use, you should avoid strenuous exercise with the watch, so as not to damage the case or handle and affect the sealing of the watch. If the water is ingress, it is recommended to send it to a professional maintenance shop for treatment in time.

First, when the watch is in water and fog, the simplest way is to wear the watch on the wrist backwards, that is, let the watch mask reflect inwards and the bottom case of the watch face outward. After a few hours, you will notice that there is less and less moisture inside the watch.

Second, prepare a little paper towel or moisture-absorbing flannel, wrap the watch tightly, place it on a 40-watt light bulb about 5 cm, and bake it for about half an hour. Later, you will notice that the moisture in the movement gradually disappears.

Thirdly, it can also be used to remove fog vapor by basking in the sun. First turn the back cover of the watch open, then wrap the watch completely with a paper towel or moisture-absorbing flannel, and take it to the sun to bask in the sun for most of the sound, which can also remove the moisture in the movement. If the watch is severely flooded, it can be left for a longer time.

Fourth, after the watch enters the water, you can first open the back cover of the watch, remove the battery, and use the hair dryer to aim at the water meter at low temperature. After blowing until completely dry, put the back cover device back from the beginning. You can also check whether the sealing ring is aging and broken when you install it, and remember that the back cover must be fastened if it is in good condition.