What should I do with a notebook that gets into the water? What to do if the laptop gets into the wa

After the laptop gets into the water, you need to unplug the power supply and remove the laptop battery as soon as possible to avoid a short circuit in the laptop caused by the motherboard being powered on. Use absorbent materials such as paper towels and cotton cloth to dry the surface of the notebook to prevent water stains from penetrating the notebook twice. Use screwdrivers, picks and other tools to remove the hardware inside the notebook and wipe it dry and air dry the water stains to reduce the risk of water stains corroding the hardware circuits.

The following is a detailed introduction: Step 1, after the laptop enters the water, the first thing is to cut off the power, the power off here is to unplug the power supply immediately, and remove it together with the battery, so that you can avoid the motherboard due to power and short circuit, step 2, remove the accessories, because the notebook is a device that combines precision accessories, and if there is a problem in one place, it will implicate multiple parts. It is necessary to remove the accessories that can be moved on the notebook, if there are external or replaceable module parts (such as optical drives, hard disks, floppy drives, expanded memory, etc.) are removed together, step 3, pay attention to be careful when disassembling external or replaceable module parts, to avoid unnecessary secondary damage, step 4, pour out the water, even if we disassemble the optical drive and hard disk and memory of the notebook, but there are still many in the notebook.

At this point, tilt the laptop in its entirety, then allow the water to flow out of the heat vents, pour as much light as possible, and send it to the service station to be handled by a trained professional engineer as soon as possible, so as to minimize the damage; Step 5: Find a soft wet paper towel or soft cloth to gently wipe off the stains, and wipe off any remaining water in the keyboard. And try to avoid abrasion of the surface. Never use a hair dryer to bake.

Because there are a lot of small plastic components in the internal accessories of the notebook, it is easy to deform the components, which can lead to worse consequences. If you use a hair dryer, it is recommended to use a cold air to blow the water out; Step 6: If the laptop fails to turn on when the laptop is powered on after the laptop is blown dry, then it is likely that the internal circuit of the laptop has been damaged, and in this case, you can only go to the maintenance center to test.

1. First of all, immediately turn off the power of the laptop system, and remove the power cord and battery at the same time.

2. Use a clean rag or tissue paper to wipe the liquid on the surface of the laptop keyboard and the machine.

3. Move the laptop near the sink and tilt the laptop 90 degrees to pour out the liquid remaining inside the computer system and keyboard.

4. Use a clean rag or tissue paper to wipe the liquid on the surface of the keyboard and the machine again.

5. Let the laptop stand for 24 hours to dry the liquid inside, and do not use a hot air dryer to dry the case to avoid overheating and deformation.

6. Reconnect the power of the laptop and try to turn it on, if it can be turned on normally, please back up the important data in the computer first

7. Regardless of whether the laptop can be used normally, it is recommended to contact the ASUS customer service center immediately after the test to arrange inspection and maintenance, so as to avoid sudden failures caused by oxidation and rust.

Unplug the computer immediately and force it to shut down, as fast as possible.

Use a paper towel to absorb moisture from the keyboard and dry it with a hair dryer.

Remove the back cover of the computer, observe whether there is any moisture residue on the motherboard, and put the computer in the ventilated sunlight for half an hour.

Send it to the repair center for repair.

1. First of all, immediately turn off the power of the laptop system.

2. Unplug the power cord and all external devices as soon as possible.

2. Wipe the liquid on the surface of the laptop keyboard and the machine with a clean rag or tissue paper;

7. Regardless of whether the laptop can be used normally, it is recommended to contact the after-sales customer service center immediately after the test and arrange testing and maintenance to avoid sudden failures caused by oxidation and rust.

It is recommended to send it to a professional repair shop for processing.

It depends on the situation of your water intake,,If you don't have much, turn off the power and blow it with a hair dryer.,And then naturally put it for a day without turning it on.。。 (That's how I got into the water this time.) People are unlucky, there is no way) if it's serious, go to the hospital and see it... In both cases ...

It can generally be eliminated。The screen has a watermark, it can only be blown with a hair dryer or placed in the sun, if the area is too large, it is better to use the sun, if the area is not large, it can be blown with a hair dryer.

The first step is to find a courier box of yellow cardboard, cut a hole out, the size of the hole is about the same size as the watermark area, stick it on the screen with tape, leak out the watermark area, turn on the hair dryer to the highest temperature of the wind, about 15 cm away from the screen across the screen to blow, blow slowly, about 10 minutes, do not blow against the screen, the high temperature will burn the screen.

As soon as the laptop gets into the water, it must be immediately powered off and forcibly shut down, and the battery must be dialed. The shutdown mentioned here is not to slowly click the mouse to shut down from the start menu, and the slower it is, the greater the damage to the notebook. After that, disassemble the machine and clean up the parts that are easily damaged by liquids such as the motherboard and keyboard.

To completely remove the motherboard, clean it with a plate washer with Kina water, and dry the motherboard to 100 degrees in a dryer. to power on again. Don't leave anything to chance.

Sometimes after turning off the machine and pouring out the water, there is no other treatment, and after leaving it for a period of time, it is turned on.

Generally, there are two results of this: one is that the machine cannot be turned on, and the other is that the machine can be used normally temporarily.

This kind of laptop that has not been treated with water will have serious consequences if it is turned on again, maybe the water has not soaked into the motherboard and the inside of the machine, it may be fine at first, but most of the sharp cases are not covered and the machine will not turn on after a day or two of use.

1. Unplug the power supply and battery immediately, and the speed of power failure directly determines the most critical factor in the severity of the damage to the notebook. Don't start shutting down slowly, and then shut down when the system shuts down normally. If it's slow, it's quite dangerous.

2. Pour out the water immediately according to the direction of the water intake, and quickly dry the water with a dry towel or paper towel. If there is water on the top of the keyboard, immediately turn the keyboard down (be careful not to let the water flow into the LCD screen), and try to pour out the water to avoid more water entering the motherboard.

3. If the keyboard gets water, remove the keyboard and observe whether the water has entered the motherboard. Carefully dry the front and back of the keyboard with a paper towel. If possible, you can use a hair dryer to dry it with cold air, and be careful not to use hot air, because the keyboard keys and other keys are plastic, which is not resistant to high temperatures, do not use hot air, and avoid blowing damage.

If the liquid is cola, vegetable soup, etc., you need to remove some of the buttons and carefully scrub them with pure alcohol. Because cola and other substances contain sugar, if it is not clear, it will corrode the wiring over time and cause damage to the keyboard.

4. Completely disassemble the motherboard, if you don't know how to disassemble the motherboard, it's best to ask a friend who knows more to help disassemble it. Observe whether there are water stains on the motherboard, and if so, carefully wipe it clean with pure alcohol. I use high-quality plate washing water to scrub the motherboard in notebook repair, but this kind of washing water is not available to ordinary people, and it is difficult to buy it in the electronics market in Nanjing, not the kind of ordinary plate washing water.

This can be replaced by pure alcohol, Note 1 must use pure alcohol, not aqueous alcohol. Then dry the motherboard, or the hair dryer should not be too high, and pay attention to protect the plastic connectors on the motherboard.

5. Carefully dispose of the moisture inside and outside the laptop shell, put the treated motherboard and keyboard in a dry place for one to two days, and then confirm that all the moisture has dried thoroughly before assembling it. It must not be powered on and turned on before processing. Because the general user has no professional drying equipment, it is necessary to let many accessories be thoroughly dried as often as possible.

Summary: If the machine still won't turn on after the above 5 steps: then it is likely that the internal circuitry of the laptop has been damaged, or the motherboard has been short-circuited. In this case, the only way to do this is to send the repair service.