Computers are 5 meters apart, and the same telecom broadband Internet access, the same XP system, ho

If it's just resource sharing between two computers, just set up a LAN on the two computers: right-click on the Internet neighbor on their respective computers --> Properties --> set up a home or small office network -->Next --> Next --> select "This computer connects to the Internet through other computers" --Enter your computer name (it doesn't matter what you enter, Be careful not to use the same name as the other machine)--Enter the team name (home or office will do, but the team name of the two machines should be the same)--Choose whether to enable print sharing (depending on your situation)--Next-->Next-->Select the completion wizard-->Wait for the wizard to complete--> complete. After that, you can see the other computer in the online neighbors of the two computers, and if there are any resources that need to be shared, as long as you set it to share in the properties of the resources on your own computer, the other computer can see and transmit it.

Note that if the transit device you connect to two computers is not a router, but a device without routing function, such as a hub or switch, then you need to set the IP address of the same address segment in the local connection of the two computers, and if you are connecting with a router, the router will assign the IP address).

I used to hear the microcomputer teacher say that you can use a twisted pair to connect the two computers, and set the IP.

You can use a LAN connection or you can install a router.

If the two places are far away, this is not possible. If the telecom broadband is bound to the port above the ** line, you can't use the same one if you change the line.

If the other party's ** line is not equipped with broadband, you can't dial the number directly, and you will be prompted with error 691 or 678. If the two locations are not far apart, you can use a router to separate the network cables, so that they are still the same and the two places share the network.

Definitely not, broadband is a signal that goes through the ** line, although in the same county, if the two are within 100 meters, you can also use the wireless direct entry account password, it is estimated that it is quite far away.

No, because the broadband is bound to the broadband port of the telecom company's computer room.

Hello. On the other hand, your broadband Internet access account can only be used on the line where you apply for broadband, and you cannot log in to the Internet on other lines.

It shouldn't be, because the broadband is bound to the ** number.

Probably not, the account number of each network cable is different.

The settings are as follows.

On the computer, open the network connection, and in the "Local Connection" field, check the box before sharing the Microsoft network file and the printer, and if not, install the network service.

1 Enter Run Group Policy in Run. Computer Configuration Windows Settings Security Settings Local Policies Security Options, find Network Access. Select Classic.

2 In the local security policy, remove guests from denying access to this computer from the network, of course you first right-click on the desktop"My computer"--"Management"--"Local users and groups"--Users, enable the guests user.

3 Make sure the computers are in the same workgroup.

Control Panel - Management Tools - Local Security Policy - Local Policy - User Rights Assignment, find "Access this computer from the network" or "Refuse access to this computer from the network", then check whether there is a guest account or other corresponding accounts, and then add or delete according to different situations to achieve access sharing.

Windows 7 has the option to open access to LAN resources.

XP believes you can find this item for LAN to build.

After that, just set it up to the same working group.

Set up in the same workgroup and share the files you need on it.

Just set them up in a working group

The first step is to connect the broadband ** cable to the modem.

The second step is to connect the cat (modem) to the router, let the router have a signal, and then connect the router through a computer, and then enter, debug the router, and you can have a network.

The third step is to connect another network cable to another computer.

The computer is a notebook, and if you need to use a wireless network connection, the router must have a wireless function.

The fifth step is to enter the name and password directly to successfully surf the Internet.

Buy a router and set the relevant network parameters on it, the router is to set up a LAN to achieve network sharing equipment, the general connection and setting methods are as follows: connect the network cable out of the broadband cat to the WAN port of the router, each computer is connected to the LAN port of the router, the IP address of the computer network card is set to automatically obtain, enter in the address bar of the computer browser, specifically to view the network parameters obtained by your computer network card, and log in through the IP address of the gateway) to log in to the router,Generally, the username and password are admin,Select WAN port settings,Set your broadband account and password to the PPPoe mode (if it is a fixed IP,choose the static IP mode),Save and restart。

You can share the folder directly and find it in your neighborhood.

Check your respective IP addresses, add a network printer, and enter the IP address of the computer with the printer in your computer to give it a try.

Connect the three machines with two routers, so that the three machines are assigned different gateways to access the Internet in a local area network.

Resource sharing through remote desktop control.

Select the question you want to share, preferably in a folder or disk, and right-click on the ......Share ......Advanced sharing ......Check the ...... Share this folderThe app will do the trick.

Both computers are set to "automatically obtain IP addresses", or two computers are set to IP addresses on the same network segment.

Create a new folder on the XP machine, set the share - the share with read and write permissions, and you can find the XP with Win7.

Win7 should be set up as a home network.

Then they have to be connected to the same route, otherwise there will be no local area network.

Shared folders will do the trick.

Was the computer able to access the Internet before?

It's because there's something wrong with the router settings or you're pulling the wrong cable.

Take the notebook to the landlord and try it on the next paragraph.

IP Issue: The route is not dynamically assigned IP address, and the incoming route is changed to dynamic IP allocation.

It is recommended that you still install the flagship version from the home version is garbage The original system that the computer just bought, right, take it and let the store reinstall the flagship version for free Other problems are not a problem.

Is your network switch not turned on; To turn on the network switch on it,

I don't know what cat you use Whether it has a routing function If it is, you can achieve it Specifically, you can check whether the cat has a routing function and how to set it The key is that the setting is also very troublesome You need to study it yourself There is a win7 system network card may not be recognized You can add a PCI network card to try.

The switch is not good, to make the router ah brother, you can't do it like this.

After the cat, add the router and then add the switch.

Brother, the XP system does not share the Internet with a router, the host has to have 2 network cards, a linked modem, and a connected switch, and the secondary server sets the IP to be in the same IP segment as the host but it must be different.