What should I do if the coil of the sock machine fails? What should I do if the sock machine is old

If the coil of the sock machine fails, then a new coil must be replaced, otherwise there is no way to use it normally.

If it fails, he can only replace it with a new one, because the original one has a problem, otherwise there is no way to use it normally.

If the coil fails, just replace it with a new one, don't use the old one, in that case, the problem will become more and more serious.

There is one of the easiest ways is to measure the current of each phase of each phase of the motor through low-voltage alternating current, and at the same time connect a capacitor in series in the detection line, the current of the three phases should be balanced, if the unbalanced phase should have a problem, the problem of failure at the same time of the three phases is rare, and the quality failure of the motor after maintenance has been improved to a certain extent.

If the coil of the sock machine fails, then you can only repair it again or replace it.

If it fails, it is recommended to restart it to see if it can be solved, in general, it is possible, but exceptions are not excluded, if it still doesn't work, it is better to ask their after-sales service.

What should I do if my socks and coils fail? Then you'll have to buy a new coil and install it. The model and specifications have to be matched to be able to press? Press it for normal use, the sock machine coil fails, you have to buy a new one.

If this machine fails, then there is no way, it can't be used, so let's replace it with a new one.

The coil of the sock machine fails, when the motor is in an abnormal working state, including electrical, mechanical and environmental aspects, etc.) The life of the motor coil will be seriously reduced.

The reasons for the failure of the fan coil are: phase loss, short circuit, coil grounding, overload, etc.

As a major socks producer, China's annual output of socks has exceeded 13 billion pairs, and will increase at a rate of 5.8% per year. However, the real economy is generally difficult to operate, and the hosiery market is subject to disorderly competition.

If it fails, it should be that there is a problem with this coil, in which case it can only be a problem with the line, or this coil has appeared. Fault.

What about the Driver's Circle School? You should set this up specifically on it, and pay attention to it from the Internet.

The coil of the socks machine fails, you should find a professional maintenance of the socks machine to solve the after-sales service of the socks machine, right?

Hello, the main problems of repairing the hosiery machine are: 1The hosiery machine is out of order:

The failure of the hosiery machine may be caused by power failure, circuit board failure, controller failure, transmission component failure, etc. 2.Poor sewing quality of hosiery machine:

The poor sewing quality of the hosiery machine may be caused by the wear and tear of the sewing head, the damage of the sewing head, the improper cleaning of the sewing head, the improper installation of the sewing head, and the improper adjustment of the sewing head. 3.The sock machine sewing speed is slow:

The slow sewing speed of the hosiery machine can be caused by motor failure, transmission component failure, controller failure, etc. 4.Incorrect sewing line for hosiery machine:

Incorrect sewing line of hosiery machine may be caused by improper installation of sewing head, improper adjustment of sewing head, improper installation of sewing thread, improper adjustment of sewing thread, etc. 5.Hosiery machine sewing thread breakage:

Broken sewing thread in hosiery machines can be caused by poor quality of sewing thread, wear and tear of the sewing head, damage to the sewing head, improper cleaning of the sewing head, etc.

There are several problems with the following aspects of the sewing machine's frequent thread breakage:

1.There is a problem with the needle itself, the pinhole is not smooth, try to change the needle.

2.The needle is thin and the wire is thick, and the wire cannot enter the wire duct and is easy to break.

3.It's really too fine, and the fabric is too hard.

4.The upper line is too tight, and the adjustment screws on the front of the machine head can be adjusted.

5.The shuttle has fiber fluff inside, and the fluff and thread are twisted together, making the thread thicker, and the thread will break if it cannot pass through the pinhole. Just clean up the area around the shuttle.

The tip of the needle is broken, the screw is loose, the needle is crooked, it is possible. Double-check it. If there is no problem, ask the technician to fix it.

There are several reasons for this.

First, there may be a problem with the hosiery machine, and first, there may be a problem with the material.

Third, there is the possibility of artificiality.

But it should be that the problem of the socks machine will be bigger, you can ask the mechanic.

Or if the material is stocked, it will also lead to an increase in the breakage rate. There should be fewer reasons for people, unless it's a new hire.

Causes: 1. The needle has burrs or rough surface;

2. The wire clamp is not adjusted well;

3. There are burrs at the hook line and the line;

4. The spacing between the hook positioning groove and the hook is too small, and the convex head is not smooth, which is easy to cause needle breakage and thread breakage;

5. The jumper connecting rod in the sewing machine head is loose;

6. There is a gap between the transmission between the machine head and the rotary hook frame.

1. Polishing and polishing with sandpaper;

2. Adjust the tension so that the bottom line junction point is in the middle of the sewing material;

3. Polishing and grinding the wiring of the rotary hook;

4. Adjust the gap and polish the convex head of the positioning groove;

5. Adjust and tighten each screw;

6. Adjust the meshing clearance of the spiral bevel gear or adjust the synchronous belt tensioner of the upper and lower main drive shafts.