What is the reason for the valve to deviate when the pressure cooker is gassing

1) Cause of failure:

1) The inside of the oil cup is too dirty, the filter screen is blocked, or the oil level of the oil cup is low.

2) There is a lot of air in the power steering system.

3) There is a foreign object in the steering system, which causes the flow control valve of the steering pump to get stuck.

4) The tire pressure is insufficient, the steering column of the pump interferes, the connection is loose, the belt of the pump is loose, slipping or the pump installation position is loose.

5) The bolts of each connection part of the tubing are loose, resulting in the leakage of steering fluid.

6) The piston cylinder of the steering gear is worn too much, the oil seal is poorly sealed, and the control valve is bonded or damaged.

2) Fault diagnosis and troubleshooting

1) Check the steering gear, steering pump control valve, oil cup filter, steering oil, and clean the entire power steering system.

2) If the pump is dirty, be sure to clean the inside and outside of the booster pump and the oil pipe (cotton gauze or other multi-fiber cloth should not be used, clean with a clean brush), and exhaust air to the steering system according to the regulations.

3) Inflate the tires according to the regulations and adjust the performance of the engine.

5) Adjust the tension of the belt and tighten the connecting screws of each part according to the regulations.

6) Check the connection parts of the tubing and tighten the connecting bolts.

7) Replace the oil line, power steering pump, or power steering gear.

If there is a problem with the pot, it is recommended to change it if it is not rotated.

1.The pressure reducing valve is blocked, and no air pressure is released, so the pressure reducing valve has no response. If the pressure reducing valve is blocked, it is recommended to replace the safety dissolution in the safety valve. Safety tablets are generally sold in supermarkets and places that sell pressure cookers.

2.There is air leakage in some places of the pressure cooker, such as the sealing ring on the lid, as well as the interface of each valve, in short, because the air pressure in the pot is insufficient, the pressure limit value cannot be reached, and no gas is released, so the pressure reducing valve will not have any reaction.

Because the pressure cooker is a dangerous electrical appliance, if it fails, you must not disassemble it yourself, but find a professional to repair it.

Precautions for using a pressure cooker.

1.The inner pot should not be boiled empty or placed on other heat sources.

2.Before putting the inner pot into the outer pot, wipe the inner pot and the heating plate clean, and rotate the inner pot left and right after putting it in, so as to keep the inner pot in full contact with the heating plate.

3.The sealing ring cannot be damaged, and it cannot be replaced by other rubber rings.

4.When the electric pressure cooker starts working, the pressure limiting valve must be dialed to the sealed position.

5.Anti-clogging covers and seals should be cleaned frequently to keep them clean, but also to ensure the tightness of the pot.

6.When the float valve is not dropped, the cover cannot be forcibly opened.

7.No heavy objects should be added to the pressure limiter or replaced by other items.

8.If you are cooking porridge in the pot, you should not immediately remove the pressure limiting valve, otherwise the soup will spray out of the exhaust pipe.

9.When turning the pressure limiter to deflate, do not put your hands and face close to the exhaust pipe of the pressure limiting valve to avoid being burned by the vented steam.

The reason why the pressure cooker valve can't come up is that the fusible sheet is melted, you can go to a store that specializes in selling pressure cooker accessories to buy it, or you can go to the Internet to see.

1. Check whether the sealing rubber ring of the pressure cooker is damaged or defective.

2. Whether the pressure limiting valve in the middle is in the correct position or whether there is food residue stuck inside, clean it carefully.

3. Whether the jump valve of the exhaust moves up and down freely, it should also be cleaned and dredged.

4. Whether the lid is broken and deformed.

5. Whether there is rice residue in the trough where the sealing ring is placed.

6. The lid of the pot did not rotate in place, almost a little, and a retractable clip inside stuck the exhaust valve.

Isn't it true that pressure cookers press the valve themselves at a certain time, and our family is like this.

If the gas valve of the pressure cooker does not turn when the Kia leads to a certain time, it means that there is a blockage inside, at this time, it should be checked for gas, clean the gas valve of the pressure cooker, and then try again, if it still does not work, then it is necessary to go to the professional department for maintenance.

Pressure cooker. The pressure reducing valve does not rotate because the pressure reducing valve is clogged and the air pressure cannot be released, so the pressure reducing valve does not rotate. It's also possible that there is an air leak elsewhere in the pressure cooker, such as a seal on the lid.

At the interface of each valve, etc., because the air pressure in the pot does not reach the pressure limit value, so no gas is released, so the pressure reducing valve does not rotate.

Due to the large internal pressure of the pressure cooker, it is easy to have an accident after the pressure reducing valve is blocked, so it should be stopped in time, and it should not be operated without authorization before the maintenance is carried out by professional maintenance personnel.

Precautions for using a pressure cooker:

1. The inner pot should not be boiled empty or placed on other heat sources for boiling.

2. Keep the inner pot and heated.

The dish is clean and placed in full contact.

3. The sealing ring of the cover cannot be damaged, nor can it be replaced by other sealing rings.

4. When the pressure cooker is running, the pressure limiting valve must be pulled out to the sealed position.

5. When the float valve falls, the cover shall not be forcibly opened.

6. When pulling out the pressure limiting valve to vent, do not put your hands or face near the exhaust pipe of the pressure limiting valve to avoid being burned.

7. It is best to pay attention to the cleaning of the anti-blocking cover and sealing ring, keep it clean at all times, and also take it as an example to ensure the tightness of the pressure cooker.

Pressure cooker. The above valve does not turn for the following reasons:

1. Pressure reducing valve.

When it is blocked, no air pressure is released, so there is no reaction from the pressure reducing valve. If the pressure reducing valve is blocked, it is recommended to replace the safety valve.

in the safe dissolving tablet.

2. If the pressure cooker valve does not rotate, it may be that there is a leak in other places, such as the sealing ring on the lid, as well as the interface of each valve, in short, because the air pressure in the pot is insufficient, the pressure limit value cannot be reached, and no gas is released, so the pressure reducing valve will not have any reaction.

Take the valve down.

See if it's loose.

If yes, you can tighten it.

The reason why the pressure cooker exhaust valve does not turn may be due to damage to the exhaust valve, or a malfunction of the control mechanism of the exhaust valve. If there is gas discharge from the exhaust valve, it may be due to damage to the sealing ring of the exhaust valve, resulting in gas leakage, or it may be due to the failure of the regulating mechanism of the exhaust valve, resulting in the exhaust valve being unable to adjust, resulting in gas discharge. If the exhaust valve does not turn, you can check the control mechanism of the exhaust valve to see if there is a failure, if a failure occurs, you can replace the control mechanism of the exhaust valve to ensure the normal operation of the exhaust valve.

In addition, check the sealing ring of the exhaust valve to see if it is damaged, and if it is damaged, the sealing ring can be replaced to ensure the normal operation of the exhaust valve.