How do you pry jeans? How to open the button hole in jeans

One way to make the hem of the pants look good is to have the tailor cut the hem first, then the part that needs to be cut, and finally the hem of the pants that started to be cut off and then on, so that it is natural, just like new pants.

It's a long time. , as long as it is appropriate elsewhere.

When he grows, you tell him to pile it in his shoes. A bunch of bulging, how good-looking, and how casual it feels.

Don't throw away the hem of the pants cut from the jeans that are too long, the old tailor will teach you how to connect the original edge.

When they go to the clothes store, they get it, and they lose some money at most.

1. Measure the required length, cut off the trouser legs, and don't throw away the original edges.

2. Remove the stitches on the original edge. If the length of this part is too long, you can cut it shorter.

3. The hem on the reverse side is not moved, and the extra part of the front is also folded inward, which looks a bit like piping.

4. This step is crucial! "Install" the trouser cuff that you just cut short with the folded original edge, and pay attention to the alignment of the trouser seam.

5. This step is handed over to the machine - needless to say. It should be noted that the joint is quite thick, and it is estimated that the household sewing machine is difficult to step on, so it is recommended to let go of the presser foot first, and try to sew it manually one by one.

Be careful with your fingers though, thimbles are a must!

6. Done! The effect is more obvious, and when you wear it on the body, you will only see the original edge, and you will not pay attention to the seams.

First, lay the jeans flat on the table, find the buttonhole that is sewn up, and fold the buttonhole in half, which is the red circle at the bottom, from the middle.

2.Then use a sharp tool such as scissors to puncture a small hole in the middle or cut the thread end joint to further enlarge the grommet.

3.Finally, while expanding from the opening to both sides, keep trying to see if the button can be fastened, and expand it to the button just fastened but not loose. It should be noted that in the process of cutting, do not cut too big at one time, you can try to cut the size while not suitable, cut too big and the button is easy to loosen.

4.If the cut is too large, you can also use a needle and thread to stitch back a few times. The button holes will be further widened, so don't cut the buttonholes too big, and you can wear new jeans after cutting.

Extended information: Jeans are also known as "sturdy pants". A type of tight-fitting pants worn by both men and women.

The front pants are unpleated, the back pants are not provincial, the door is zipped, the front trousers are equipped with a diagonal pocket on the left and right, the back is equipped with two patch pockets with pointed waists, and the seams of the pockets are nailed with metal rivets and pressed with topstitching. It has the characteristics of wear-resistant, dirt-resistant, close-fitting and comfortable to wear.

1. If the circumference of the trouser leg is narrowed within 1 cm, it can be modified from the outside. When it is more than 1 cm, in order to balance the amount of fabric on the inner and outer sides of the pants, and ensure that the style remains the same, it needs to be narrowed on both sides at the same time.

2. Alteration tools: special clothing scissors; Sewing; Iron; alteration cones; Fully computerized lockstitch sewing car.

3. The focus of the small circumference of the jeans trouser leg is: the inside of the trouser leg.

4. The pants of jeans are low-waisted curved type, if the inside of the pants is tightened as a whole, the crotch will be tightened at the same time. The crotch effect of shed silver affects the wearing experience.

5. In order not to affect the capacity of the crotch type, choose to avoid the crotch modification and reduce the width of the inner side of the trouser leg to 5 cm below the root of the thigh. At this time, it does not affect the crotch capacity, and at the same time, the trouser leg is narrowed.

Fold the sewn buttonhole in half from the middle. Then cut it with scissors. Note that when cutting, do not exceed the boundary of the buttonhole, otherwise the buttonhole is too large to buckle the button. Some of the buttonholes of the newly bought pants are sewn with thread, and the buyer needs to use scissors to cut the buttonholes. <

Fold the sewn buttonhole in half from the middle. Then cut it with scissors. Note that the cutting should not exceed the boundary of the buttonhole, otherwise the buttonhole is too large to buckle the button, and some of the buttonholes of the newly bought pants are sewn with thread, so the buyer needs to use scissors to cut the buttonhole.