What is the problem with the motherboard detection card boot 60

If the ASUS P58 SE motherboard appears 60**, the memory is broken, and the memory can be replaced.

There are chip damages, CPU and northbridges, and graphics card focused suspicions

Viruses, fans, silicone, dust inside the case. Let's exclude them one by one.

Wipe off all the inside of that host with paper, and I'll do it like this, and that's how it was done.

What doesn't understand into my space.

Test card 06 means the following:

debug card diagnostic**:06

What it means: 06 Make the circuit chip initially ready, deactivate **, parity, DMA circuit chip, and clear the DMA circuit chip, all page registers and CMOS stop bytes. The rom calculation has been started to check the sum of the rombios, as well as to check if the keyboard buffer is cleared.

The DMA initial page register read and write test is in progress or fails.

Why: DMA is an input/output operation that enables automatic batch data exchange between high-speed peripherals and main memory under specialized hardware (DMA) control with minimal CPU intervention.

06 The problem is complicated, it may be a problem with the north and south bridges, focus on checking the memory. Or try to turn off the keyboard incorrectly in the BIOS.

Yes. You can't trust the detection card too much, sometimes it's not accurate, first change the CPU memory, determine if it's a problem with the motherboard, and then consider repairing the motherboard.

The computer motherboard is the most basic and important part of the computer, and the computer motherboard is the place where most of the parts of the computer are held.

Generally, motherboards are not so easy to break. After we remove the motherboard, don't immediately take the multimeter to check the circuit. It should be cleaned with a brush and alcohol. Then put it on the workbench to analyze the specific cause.

When placing it on the workbench, be sure to put a foam board or book under the motherboard. This is to prevent there from having broken metal around, and then when we light up the motherboard, it will cause a short circuit and burn the motherboard.

Common faults of computer motherboards are: whether the capacitor is bulging and leaking. This means that the capacitor is broken, and the worse capacitor is enough. There is also a multimeter to measure the chip resistance and whether the chip capacitor is damaged.

If it is a black screen, a blurred screen, always restarting, blue screen, such a situation is generally related to the parts on the plug-in on the motherboard, we can use the replacement method to try a new one, whether it is broken, and then judge whether the motherboard is faulty.

00 means that the computer is not running at all, which means that the CPU is not working at all. Power failures, motherboard failures, CPU damage can all occur in 00 yards. Eliminate the fault of the power supply, and the motherboard may be the most damaged.

00 means that the CPU self-test has not passed, and the motherboard or U is broken, it is possible that 00

It's hard to say, it's possible that the motherboard may be a CPU, you can change a good CPU and test it.

The motherboard diagnostic card shows **66 meaning:

DMA units 1 and 2 have been programmed and initial preparations will be made using interrupt controller No. 59.

The cache registry is optimized.

Solution: It is your computer's memory, graphics card, and even network card may have problems, it is recommended that you dial it down in turn, wipe its gold finger part with alcohol, and clean up the dust on the motherboard, reinsert each card, restart the computer to try, if it still doesn't work, then you have to send it for repair, it is estimated that the hardware is broken.

Motherboard Troubleshooting Card:

It is the detection results of the BIOS internal self-test program in the motherboard, which are displayed one by one, and the computer fault can be quickly known in combination with the meaning of the cheat sheet. Especially when the PC cannot boot the operating system, the screen is black, and the speaker does not call, the use of this card can reflect its convenience and make you get twice the result with half the effort.

When a critical component fails, the machine is forced to shut down, and the display has no cursor, so the screen does not respond at all.

Then, the non-critical parts are tested, and the faulty machine continues to run, and the display is not displayed, and the card is inserted into the expansion slot. According to the ** displayed on the card, refer to which BIOS your machine belongs to, and then find out the cause and location of the fault represented by the **, you can clearly know where the fault is.

1. There may be a problem with the memory, graphics card or BAI network card copied by the computer.

2. The theoretical definition of **zhi66 displayed by the motherboard diagnostic du broken card is: the programming of DMA device 1 and DAO2 is completed; Initial preparations will be made using the No. 59 interrupt controller. The cache registry is optimized.

DMA (Direct Memory Access), on the other hand, is a mechanism for transferring data quickly. cache is a buffer, which causes problems with the memory, graphics card, or network card of the computer in the analysis room. You can unplug them once and wipe their gold finger part with alcohol, clean the dust on the motherboard, reinsert the cards, and restart the computer.

What do you mean? According to the specific identification of the fault, and then the corresponding fault can be corresponded.

Causes of computer motherboard failure:

Component causes: Because the quality of the components and chips on the computer motherboard is not good, it will lead to aging and damage to the motherboard, which will cause the motherboard to fail.

Human reasons: When users use the computer, if they hot-swap the hardware or touch the connector with metal objects at will, it will cause the motherboard to malfunction.

Causes of static electricity and dust: Dust or static electricity on the computer motherboard can cause the motherboard to be in poor contact, short circuit, or burn the motherboard chip, resulting in motherboard failure.