I want to use one router to dial up Internet access to multiple computers at the same time

Use WAN to connect to the external network cable, use the LAN port to connect your computer, and the settings are as follows (just some details of the general settings are figured out by yourself):

Save the user password in Routing - Network Parameters --- WAN port settings (select PPPoe for connection type), then enter the DHCP server, select Enable DHCP, and use automatic IP acquisition on the computer, and you should be able to surf the Internet normally.

If you want to configure a static IP, go to --DHCP server --- static address allocation (fill in the MAC address of the computer network card in front of it, and fill in the IP you want to assign in the back, but the IP should be within the address pool that DCHP can assign. The MAC address is in the Windows--- Command Prompt and the configuration information will be displayed after you hit ipconfig -all in it, and the physical address in it is the MAC address.

After installing the route, type or, press enter, enter the username admin, enter the password admin, click 'Quick Settings' in the page, select your link type, generally ppoe, enter your Internet account and password, complete, there is a save key and click Save.

Then set the IP address to be dynamically assigned on the page! Turn on all the computers you want to access the Internet, ** to customer service, and ask for a reset password! That's it. After that, the computer can be shut down, but the router should not be powered off. Because every time there is a power failure, the customer service needs to reset the password.!

Wiring: cat - WAN port; Each LAN port is connected to each computer.

The route settings are set using tp-link as an example

Enter the routing setting interface in the browser, the default username is admin, and the password is admin;

Click "Network Parameters", then click WAN port settings, and change the WAN port connection type to "PPOE";

Fill in your Internet access and Internet password;

Lower down the dot on "Normal Dialing Mode";

Then go down to "Connect on demand", and the waiting time for automatic disconnection will be changed to 0 minutes;

Click "Save" below;

Click "System Tools" in the left menu, find "Restart Router", click OK to go online, and all of them are set to automatically get IP

Open IE to enter.

Just follow the prompts and you're good to go

Buy the router back first! (I bought the "Golden Wave" brand) and then hit "technical support**", on the back of the box, there is also "free service in other cities**".

They will be very enthusiastic and patient to tell you the ...... operation

That's how I just installed the router.

If you read too much on the Internet, your head will be ......

Summary. Two routers can dial up Internet access at the same time, and the specific two methods are as follows:

First method:

From the LAN port on the original router to the LAN port of the new router, the IP is set up the same as the original computer. It's very simple, it is to turn the router into a switch, and it is a waste of one more port, or you can't connect to one more machine.

The second method:

From the LAN port of a router to the WAN port of a newly purchased router, a series of settings are required.

There are two ways to set it up:

1. If DHCP is enabled on the higher-level router and there are no other DHCP servers, the second-level route can be obtained using dynamic IP.

2. If the DHCP server is not enabled on the higher-level router or there are multiple DHCP servers and static binding, the secondary route can be set to static IP mode.

Can two routers dial up at the same time?

Two routers can dial up the Internet at the same time, the specific two methods are as follows: the first method: from the LAN port on the original router to the LAN port of the newly bought router, IP or something is the same as the original computer settings.

It's very simple, it is to turn the router into a switch, and it is a waste of one more port, or you can't connect to one more machine. The second method: from the LAN port of a router to the WAN port of the newly purchased router, a series of settings are required.

There are two scenarios: 1. If DHCP is enabled on the higher-level router and no other DHCP servers exist, the second-level route can be obtained using dynamic IP addresses. 2. If the DHCP server is not enabled on the higher-level router or there are multiple DHCP servers and static binding, the secondary route can be set to static IP mode.

Have a great day.

No. The ISP accepts only one access.

You can set one of them to be autodialed.

Broadband dial-up Internet access: When the router was not used before, the stand-alone computer system used the broadband Lian Songxiang to dial the wild bump number, and the operator gave a username and password. This is currently the most common way to access the Internet, and most home broadband is the Internet access method.

As shown in the figure below, in the router interface, find "Network Parameters" and "WAN Port Settings Noise".

Then, you'll see the following diagram.

4.Reboot and the setup is successful.

Can an optical modem at home connect to multiple Wi-Fi networks and create different external network IPs?