When I install the system, the network connection fails to be automated, how do I set the connection

This step can be skipped during installation! Just press skip and then set up the network after installing the system, as follows:

1. Set the IP address first. In general, the default auto-detect IP correctly detects your IPIf you find that your local connection is not connected, you will need to manually set the IP protocol.

If you don't know how to set it manually, you can uninstall the driver on your network card, restart the computer, and reinstall the driver. That way, it should be able to detect your IP automatically.

2. Create a new network connection. (This is connected to the Internet) right-click on the Internet Neighbor and select Properties. Select it in the dialog box that opens'Create a new connection'Open another dialog box.

Then follow the prompts inside to select the network connection method. (In this case, I'll take a broadband connection as an example) select the first one in the conversation you just opened and press Next. Again'Set up my connection manually, next.

Pick the second one, the next step. The ISP name is filled in by yourself, and then the next step. Then just press Next and you're done.

Finally open this, enter your username and password, and press connect to OKNeedless to say, right?

Supplement: Faint! If it's homework, you just answer it!

A: I chose to skip over, and then set it up in my way. (Because the system is not fully installed, the driver of the network card is not installed, so it cannot be connected in front!)

Also, if the network card driver is installed correctly and the network cable is fine, then it can be judged as a hardware problem. (Here's a little bit of knowledge: when the network cable is plugged in, the LIC light will turn on.) )

Ping your own IP, and if it doesn't work, it's a problem with the network card.

Isn't there an Internet connection wizard?

Just do what he does, and if it doesn't work, create a new local connection.

When installing the system, there is a step to connect to the Internet to find the program.

In fact, this step can also be skipped.

Because it is still installed, it may be that your network has not been set up, so you can't connect.

By the number of banquets in the system settings can not connect to the network Hello dear,!"Step 1: Check if it is a problem with the mobile phone 1, see if the airplane mode is turned on, if it is the airplane mode, then it will definitely not be connected to the wireless network.

2. Check whether the mobile phone is short of power, sometimes it is impossible to connect to the network due to lack of power. 3. If it is not the above 2 reasons, then take your mobile phone to the closest place to the router and try it. 4. If it doesn't work, then restart the phone and see if it can connect.

5. If it still doesn't work, open the wireless network settings and advanced settings of the mobile phone, and adjust the WLAN hibernation setting to "never". What happens if the phone is not connected to the InternetStep 2: Check if it is a router problem.

1. Check if the password of the router has changed, causing the phone to be unable to connect? 2. Check the indicator light of the router to see if it is disconnected. 3. Then open it and look at the settings, is there a wireless cancellation reputation?

4. Restart the wireless router and see if it is resolved. In addition, there is another situation, what should I do if I find a wireless signal and the connection is unsuccessful? Step 1: First of all, check whether the router is connected to the external network, log in to the router management interface, and see whether the WAN port parameter is non-0 in the running status - WAN port status, if it is 0, please set it again according to the router quick setup guide.

1. Open the "Control Panel" - "Network and Sharing Center" - "Change Adapter Settings" - right-click the current network card - click "Disable" in the menu. Then right-click and select the current NIC - click "Enable" in the menu. The purpose is to release all network parameters of the current NIC and reconfigure it.

In most cases, the fault of obtaining the parameters of the NIC can be solved. 2. You can use the "360 disconnected first aid kit": If you have installed 360 security guards on your computer, then when you encounter a network disconnection, you can open the 360 security guard, click "more" in the lower right corner, and find the smart code "disconnected first aid kit" - comprehensive detection", after the results come out, if there is an abnormality, Huyin can directly click "Fix it immediately"!

3. Check the DNS in the network configuration: Although the gateway we connect to the router is normal, when the DNS in the network configuration is lost, or the DNS server in the configuration cannot be resolved, it will also cause a network outage. Open the Command Prompt window and type ipconfig all in the cursor to view the DNS parameters in the current network configuration.

In general, you can set the "Preferred DNS" to the gateway and the "Alternate DNS" to "OK. 4. Reinstall the network card driver: If the computer cannot connect to the network, it is likely that there is a problem with the network card driver, so you can also consider reinstalling the network card driver, the specific steps are as follows:

1.If you are in Windows 7, you can click the start menu to open the "Device Manager"; If it is a Windows 10 system, you can right-click on "This Computer" and select "Properties" - Device Manager, or you can open it with Windows key + R, enter the command [, and press Enter to open it. 2.

In Device Manager, find the network adapter that contains controller, right-click, and select Uninstall. (In the pop-up page of the uninstallation, note that do not check "Remove the driver software of this device", otherwise it will not be recovered) 3After the uninstallation is complete, right-click on the "Network Adapter" and select "Scan for Hardware Changes", and the driver will be reinstalled.

5. Use the reset network command: open the "Command Prompt" window as an administrator, and then enter "netsh winsock reset" directly behind the cursor.

Generally, when installing the system on the computer, there will be a driver package with a size of about 1G in the system image, which contains the drivers of the system hardware, such as graphics card drivers, sound card drivers, network drivers, etc. The most common problem is that after installing the system on the computer, the computer cannot access the Internet due to the inability to match the appropriate driver, the specific steps are as follows.

Steps:1First of all, make sure that there is no matching NIC driver installed on the computer, open the Device Manager, and find the option in the red box in the figure below, that is, "Ethernet Controller".

If the yellow signs shown in the following figure appear in these items, it can be determined that the computer cannot access the Internet normally due to the failure of the installation on the Internet.

3.After the software is installed, open the software, the software will automatically detect the basic status of the hardware driver after running, if the network driver is not installed in the computer, the software will pop up the page as shown below.

In the figure below, there will be a *** icon that matches the network card driver of this computer.

5.Double-click to install the NIC driver on the computer, and the software installation process is shown in the following figure.

6.After the installation of the network card driver is completed, the interface as shown in the following figure pops up, and you can find that the difference sign of the Internet icon in the lower right corner of the desktop has disappeared, and you can surf the Internet normally after the sign shown in the following figure appears.

For the newly installed system, have you installed the NIC driver?

1) If it is a problem with the broadband itself, first directly connect the broadband network cable to test, if it is a broadband problem, contact the broadband customer service to solve it.

2) If it's a problem with the router, if it can be used originally, it can't be used for the time being, my own practice is to disconnect the power of the router and plug it in, and I'll take a look. In there is a factory reset, from the new strict according to the manual settings can be used, I don't understand, it is not recommended to set it at will (this is under the premise of the correct physical connection, sometimes the router is slow or failed to find the IP address, not that the router is broken).

If it can't be solved all the time, it is recommended to call the customer service of the router**, they have **** guidance, I encounter problems that I can't solve by myself, it is very useful to consult the advice they give, and they will give you the correct advice for your settings or operations.

3) If you turn off the wireless switch, turn it on, if it is a wireless connection with software, it is normal for the software to be difficult to use and often have problems quietly, there is no better way to use the limbs, use a router. In addition, it is caused by the network card driver is not or is not suitable, and whether there is a problem with the network cable interface or network cable.