How to set up the D Link DI 504M

1. Connect the main line to the WAN port (the one close to the power supply) 2. Connect the computer with the LAN port with a network cable 3. Open the browser, enter, enter the management interface 4. If you are dialing, enter your username and password on the WAN settings, and then click "Copy MAC address from the client" (if the network service provider restricts MAC, otherwise, it can be ignored, the same below); If you are specifying an IP, enter the IP address, subnet mask, default gateway, and DNS server address provided by your network provider. 5. Everything is OK, you can go online.

The Deerringer House has a detailed description.

Connect the original network cable to the host to the WAN port, and then use the network cable to connect the LAN port and your two computers, check the settings of your local connection, the IP is set to automatically obtain, DNS too, restart.

After restarting, open the browser, enter the management interface, dial PPOE, enter your ADSL password, and go all the way to the next step.

Then I'll go into more detail. Don't be bothered.

First of all. The line that comes out of the moden to connect to the computer has to be connected to the WAN port of the router. Then enter IE on the computer, if it doesn't work, enter it into the router.

Generally, after entering, there is a setup wizard, and you follow the guide step by step, and don't change anything. Just select PPPOE in the dial-up mode, then enter your broadband Internet account password, connect and click Save after connecting. If there is no setup wizard then you click on the network parameters.

Select WAN port settings. Then the one that selects the dialing mode will appear. Or choose PPPoE.

Then the operation is the same.

Generally speaking, the Internet is already available at this point.

After resetting the router to factory settings, there is a small hole in the back of the router, which says reset or rst, find a small and sharp thing and poke this hole for more than 5 seconds to restore the factory settings of the router, and then reconnect and set the router: connect the network cable out of the broadband cat to the WAN port of the router, connect each computer to the LAN port of the router, the IP address of the computer network card is set to automatically obtain, enter yes in the address bar of the computer browser, Specifically, you need to check the network parameters obtained by your computer's network card, log in through the IP address of the gateway) to log in to the router, the general username and password are admin, select the WAN port settings, set your broadband account and password to the PPPoe mode (if it is a fixed IP, choose the static IP mode), save and restart.

Is there an address on the router? It seems that there should be an address and then enter the address settings.

The steps to set up the DIR-505 Mini Router are as follows:

1. First of all, connect the router, the cat and the computer with a line.

2. After the three are connected with a line, enter the router's ** (router login** on the back of the router).

3. Enter the Internet access and password given by the business hall, and click Enter.

4. At this time, you can set the password of the router, after setting it, click Next. This completes the setup steps of the router.

Set your computer to automatically get the IP and connect the router to the computer with a network cable. Go to the router settings. Connect the broadband cable to the Internet interface of the router, connect the computer to the network cable port of the router with a network cable, adjust the IP and DNS address of the computer to automatically obtain, open the browser, enter the address bar, the user name is lowercase admin, and the password is not.

After logging in, click on manual settings, set dynamic IP, broadband if it is a monthly subscription, the connection mode selection is always, save the configuration and restart the router, and then go to the Internet column of the status to see, whether there is an IP address to dial up, if there is still not, you click advanced - advanced network in the speed of the WAN port to 10Mbps and then try. As long as you have an IP address in the Internet column, you can surf the Internet. Turn on the wireless function, select an encryption method, and enter a password.

Today's routers are all web settings, and the manual should have them.

Use one network cable to connect the broadband modem to the router broadband port, and then use another network cable to connect the router to the computer.

Then enter the router home page settings, due to the different router settings of each manufacturer, please check the router setup manual by yourself or go to the Internet to check the same model of router setting method.

You can set the broadband username and password in the router, and you don't need to manually connect to the broadband dial-up after setting, and there is an option to set up PSP Internet access in the wireless router.

In fact, the CD in the accessories has detailed instructions and tutorials, as well as quick setup programs. Put the disc in the drive. It's a lot simpler.

You can take a look at this friend's space, which has a detailed **introduction, you can understand it when you look at it.

There's probably an option called Virtual Services. You can select this and add the IP of your machine to be mapped out.