What should I do if the refrigerator compartment is bulging?

The wall of the freezer compartment of the refrigerator is bulging, so find out the cause of the bulging first.

If your refrigerator is out of use in winter, it probably has a lot to do with it. There are two reasons for the bulging of the inner wall.

1.The pressure of the evaporation system is increased by deactivating the temperature and causing its weak points to leak in the interlayer, freon.

The pressure causes the inner walls to bulge, which is the last thing you want to happen (difficult to repair and not very effective). Must be sent for repair.

2。The quality of some refrigerators is problematic, but the inner wall is partially deformed due to low temperature discontinuation and high temperature return (the temperature difference in the refrigerated room is small and the deformation is small).

3.If the inner wall of the refrigerator box is blistered, it means that there is a break in the inner wall of the refrigerator box, which leads to excessive water and water vapor.

When the temperature of the refrigerator drops, the water in the wall freezes, causing the wall of the box to bubble.

In this case, if the foaming is not very serious, you can temporarily stop using the refrigerator, open the refrigerator door, and let it stand for a long time to allow the water in the box wall to fully evaporate, and then seal the damaged part with glue and transparent tape.

If the foaming is severe, the refrigerator can only be scrapped.

It's very cumbersome to deal with. Most of this bulge is caused by too much moisture entering the inside of the refrigerator box, and the moisture condenses into ice in a low temperature environment. At this time, you need to cut off the power of the refrigerator, take out all the food stored in the refrigerator, wipe the moisture in the refrigerator with a towel, keep the refrigerator door open and ventilated, let the water inside evaporate as much as possible to find the damage point of the bulging position, and seal the damaged part with glue and tape to prevent the water from continuing to enter the box.

At the same time, it is also necessary to rule out the situation caused by local refrigerant leakage in the system piping.

Summary. 1. If the bulge on the inner wall of the refrigerator is not very serious, the refrigerator can be temporarily stopped; Then open the refrigerator door and let it stand for a long time to allow the water in the wall of the box to fully evaporate; Finally, seal the damaged area with glue and scotch tape.

4. If the inner wall of the refrigerator is bulging due to refrigerant leakage, it is necessary to power off the refrigerator, and then contact professional after-sales service personnel for maintenance.

5. If the foaming is serious, you need to replace the refrigerator again.

What should I do if the refrigerator compartment is bulging?

1. If the bulge on the inner wall of the refrigerator is not very serious, the refrigerator can be temporarily stopped; Then open the door of the refrigerator and let it stand for a long time to allow the water in the wall of the box to fully evaporate; Finally, seal the damaged area with glue and scotch tape. 4. If the inner wall of the refrigerator is bulging due to refrigerant leakage, you need to power off the refrigerator, and then contact professional after-sales service personnel for maintenance. 5. If the blistering is more serious, you need to replace it with a Weiqi refrigerator.

If you don't plug it in, you don't have a bulge.

There are certain reasons for the bulging wall in the refrigerator freezer, and the specific original liquid is as follows: 1. The bulging wall in the refrigerator freezer room may be due to the increase in the pressure of the evaporation system due to the deactivation of the reheating, resulting in the leakage of its weak place in the interlayer, and the pressure of freon makes the inner wall bulge, so it is necessary to contact the after-sales service personnel for maintenance. 2. The bulging wall of the refrigerator freezer may be due to the quality problems of some refrigerators, but the weak part of the inner wall is deformed due to the low temperature discontinuation and the medium and high temperature of the reheating banquet.

3. Or it may be due to the leakage of refrigerant in Jijishan, which causes the inner wall of the refrigerator to bulge.

It's really not okay to kiss, you can contact your refrigerator customer service.

Hello, there are certain reasons for the bulging wall in the refrigerator freezer, the specific reasons are as follows: 1. The bulging wall in the refrigerator freezer may be due to the increase in the pressure of the evaporation system due to the deactivation of the reheating, resulting in the leakage of its weak place in the interlayer, and the pressure of freon makes the inner wall bulge, at this time, it is necessary to contact the after-sales service personnel for maintenance. 2. The bulging wall of the refrigerator freezer may be due to the quality problem of some of the buried rock of the refrigerator, but the deformation of the weak part of the inner wall due to the deactivation of the rock row and the high temperature return is due to the low temperature.

3. Or it may be due to the leakage of refrigerant, which causes the crude liquid in the refrigerator to bulge.

The reason is that there is a working leakage of the refrigerant of the refrigerator, and the pressure will also increase significantly, resulting in a bulging inner wall, which needs to be shut down in time for maintenance; The reason may be that there is a certain fault in the refrigerator itself, and there is no uniform material in the process of setting the foam layer, and the package is relatively small in this case, and there is no need for targeted maintenance.

1. Check the working range of the refrigerator's refrigerant, due to the long-term working process of the refrigerator, there may be a certain aging of the pipeline, resulting in the leakage of the refrigerant, and the pressure inside the pipeline will also increase significantly, which will lead to the rapid bulging of the inner wall.

2. In the process of refrigerator processing, the manufacturer itself has certain quality defects, in the process of foaming layer setting, it can also achieve a good material setting, effectively reduce the corresponding bulge size, for the case of the bulge is relatively small, it will not affect the working state of the refrigerator, for this case, the user does not need to carry out special maintenance work, of course, it is also necessary to detect the specific size change of the bulge in time, and reasonably avoid the hidden dangers of the refrigerator.

The reason may be that in the process of the refrigerator being shut down, the pressure of the evaporation system rises and the weak places are caused, the refrigerant interlayer is leaked, and the pressure of the freon is bulging in the room, so it is necessary to pay attention to the correct refrigerator closing mode; The reason may be that there are quality problems in the internal process of the refrigerator in the processing process, and the return temperature of low-temperature shutdown is too high, resulting in corresponding internal deformation.

1. In the actual work process of the refrigerator liner, it is also necessary to pay attention to the correct operation mode and operation method, if the pressure of the evaporation system rises when the refrigerator is closed, it will lead to work loopholes in weak places. If obvious refrigerant leakage is found, ensuring the appropriate refrigerant pressure working range can also solve the problem of inner wall blowing in time.

2. The manufacturer has corresponding quality defects in the actual processing process, especially when it should be used specifically, and the low temperature is too high to cause a certain deformation of the inner wall. To ensure the correct use of the way and use skills, of course, it is also necessary to consider the size of the inner wall bulge, whether it affects the normal operation of the refrigerator, and timely repair the loopholes of the mezzanine. Effectively ensure the comprehensive heat exchange effect of the inner wall, whether it will not reduce the refrigeration infiltration performance of the refrigerator, and improve the fresh-keeping working environment inside the refrigerator.