What to do after the toilet construction is completed

After the bathroom is waterproofed, it takes 24 hours to do the closed water test.

1. After the waterproof construction of the toilet is completed, it is necessary to wait for the coating of the waterproof coating selected"Finalization"(i.e., the meaning of complete solidification) before testing the water.

3. The water can be tested 24 hours after the normal construction is completed. The test time is 24 to 48 hours.

1. Ground leveling before waterproof treatment of the bathroom.

The ground is oriented to the slope of the floor drain, cement mortar or bean stone concrete can be used, but the surface should be flat. The slope near the door is small, and the slope near the floor drain is large, so you can grasp it according to the specific situation. The ground is uneven, and it may be uneven when applying waterproof coating, or the ground is easy to crack because of unevenness, which will crack with the ground even if the waterproof paint is applied

1. Strengthen waterproofing at the root of the pipeline.

The pipeline passes through the root of the floor slab to strengthen the waterproofing. After the pipe root building sealing paste is sealed tightly, and the cement is smoothed and the foot pads are smoothed, the glass wire cloth reinforcement layer is 1 or 2 layers when brushing the waterproof coating. The same measures are taken near the floor drain.

2. Waterproof wall treatment in the bathroom.

The wall surface is clean and flat, without floating ash and small particles, and the original corner or slope angle is wiped at the junction of the wall and the ground. When brushing waterproof coating, paste 1 2 layers of glass wire cloth reinforcement.

3. Waterproof painting of the bathroom.

Installation of finished products, such as bathroom cabinets, sanitary ware, etc.

The decoration of the bathroom is in place, which has a direct impact on our future life. Many people are also paying more and more attention to the construction of the bathroom when decorating. Now let me tell you how to construct the toilet and what are the steps.

During the construction of the bathroom, it is particularly important to do a good job of waterproofing. When the toilet is constructed, there are the following steps. Judgment.

The first step: do a good job in hydropower infrastructure projects.

From a safety point of view, it is better to go up the bathroom water pipes and wires than to go down. However, many "guerrillas" are greedy for labor-saving, and water and electricity go to the ground, and even dig grooves and round holes in the bathroom.

Step 2: Clean the base and walls.

The house is decorated with waterproof, involving a balcony, a kitchen, a bathroom, but the focus is on the bathroom. First of all, use a small metal hammer to knock on the wall and ground, if you find a "poof" empty sound, it means that there is a hollow drum inside, and you must knock out all the hollow drum parts. Then carefully clean the four wall base and the ground, pull out the nails, clean up the miscellaneous garbage, preferably rinse it with clean water, and then let it dry.

Step 3: Do the first level of rigid waterproofing.

All kinds of sewer pipes in the bathroom can not be changed, and try not to change them; In case of change, you must not use cement mortar to fill the pores, and you must plug the leakage king to fill it three times. The most leaky areas in the room are the four sides around the sewer pipes and the corners of the walls, so these key areas should be paid special attention. The ground should also be divided into three blocks around it, and there should be intervals.

In this way, a rigid layer of waterproof armor was worn on the ground. A slope should be made in the bathroom threshold mold, painted high, to prevent water from flowing back into the outside room, and the threshold stone must be slightly used fine cement mortar to plug the leakage Wang wet paste. Step 4:

Elastic waterproof coating to do the second level.

After a long time in the new house, the hard plugging king elastic coating will be cracked alive due to settlement, thus losing the waterproof effect. Therefore, it is necessary to add a second insurance - elastic waterproofing coating. Generally, the wall is made moisture-proof first, so that it is more than 1.8 meters.

Because people will splash water on the wall tiles when they take a bath, the gap between the tile molecules is large, and the water molecules can easily enter the wall and penetrate into the wall of the opposite room, resulting in the paint peeling off on the back of the bathroom and the moldy and discolored wallpaper. The wall is moisture-proof, and then the wall tiles are pasted, and then the ground decoration is waterproof. In the construction of the bathroom, whether it is the material or the quality, we must be strict.

The construction of the bathroom is done well, which brings a lot of convenience to our future life.

1. Carry out the transformation and adjustment of water and electricity lines first; 2. Adjust and inspect the dust core according to the number of supporting electrical appliances in the bathroom and the installation location, and then pave the wall tiles; 3. Carry out ceiling construction and joinery decoration; 4. Install a bathtub or customized shower room; 5. After the bathtub is installed, the bathtub skirt tiles are paved; 6. Install washing equipment such as toilets and handwashing tables; 7. Finally, the ground is paved and painted.

What are the tips for small bathroom decoration.

1. Planning area.

The bathroom is a place for people to shower, wash and go to the toilet, because the bathroom uses more water, many families will separate dry and wet when decorating to improve the quality of life. If it is a small bathroom, you can install a shower door or shower curtain, which can not only have a good isolation effect, but also save space.

2. Select the material.

For small bathrooms, there are not too many sanitary ware, but they must be practical, such as a double-rod towel rack, which looks good, but the actual use is not very difficult. The glass partition where cosmetics are placed must be selected to avoid damage to the glass partition and cause unnecessary losses.

3. Choose a lamp.

Usually the light in the small bathroom is relatively dark, so you should pay attention to buying lamps and lanterns, and be sure to choose waterproof solar wall lamps or explosion-proof incandescent chandeliers to add light to the bathroom.

4. Washing area design.

The basin of the small bathroom should be smaller, not too much decoration, simple enough. Mirrors are an indispensable piece of equipment in the bathroom, and you can use a simple square mirror, a simple towel rack and a basin, which is more convenient and quick to use.

5. Storage design.

There are many toiletries and daily necessities in the bathroom, and if the storage design is not good, it will affect daily use. Therefore, the small bathroom can put some multi-functional storage boxes, which are beautiful and tidy, and will not look too crowded. You can also set up a bathroom cabinet in the bathroom, and put all kinds of toiletries in the cabinet, and the storage effect is very good.

What aspects need to be paid attention to in bathroom decoration construction? Bathroom decoration is very detail-oriented, if you ignore these details in the construction, then there will be trouble in the future service life, so you must pay attention to these details in bathroom decoration. The most important thing for bathroom decoration is to do a good job of waterproof construction, there are many people to do waterproof construction is meters, in fact, it is not good, it is best to do it in one step, reach the top floor, and avoid hidden dangers in the later stage.

<>In addition, the restroom floor should also find a good slope so that the water can flow smoothly into the sewer and there will be no standing water. Refers to the slope of the bathroom tiles, the head office understands, the bricklayer basically understands, but it does not mean that everyone understands, some slopes are more pasted. Qualified bricklayers make the floor drain to the lowest point, which means that some people do floor drains, that is, dig a hole in a whole brick, which is not a good or bad practice.

I'll start by cutting the tiles around the tiles into small pieces so that I can place the drain in an absolutely low position.

If you're just digging a hole in the middle of the tile, it doesn't have to be the lowest, it should be parallel to the rest of the place, or even a little higher. So this time the water may not automatically flow into the sewer and you have to sweep it. And you don't look at the tiles, do the slope, there will be a problem if there is no slope under the tile, what is the problem?

That is, the water that leaks from the tiles will accumulate on the ground and form an odor over a long period of time. But if the slope is well maintained, the water will naturally flow into the floor drain. Some people may not understand that the method of pasting the ground is the easiest to hollow out when the ground is leveled and then he looks for slopes and uses gray tiles of different thicknesses.

A truly experienced mason must first smooth the bottom and then follow this shape, and an inexperienced mason is directly full, and he can always rely on uneven walls. Find the thickness of the volcanic ash. To do this slope is to find the ground to find the cement slope, and then according to the shape of the cement slope, let the tiles be paved, and will not be found with ash, this is the experience.

So an inexperienced master at this point is not good.

I think one of the most important things in bathroom decoration is to do a good job of waterproofing, waterproofing is the top priority, and another is that the color and layout should be reasonable, and it is best to achieve dry and wet separation.

In the decoration of the bathroom, it is necessary to choose a siphon toilet as much as possible, it is best to do a good job of dry and wet separation, leave a certain distance on both sides of the toilet, do a good job of waterproof and moisture-proof treatment, and reserve a water circuit.

Be sure to do a good job of waterproof coating, the ground must be tilted, be sure to install soundproof cotton for the pipes, be flat when tiling, and make the wall waterproof.

If the bathroom decoration is unreasonable, it will bring some troubles to the future bathroom life, such as waterproofing is not done well, which affects our lives, and may also affect neighbors.

Next, Xiangxiang I will share with you 5 matters of bathroom decoration and construction, and see if you have paid attention. First, the threshold.

The threshold is a barrier to prevent water from spilling out of the bathroom, and its design and construction points are:

1. The upper plane of the threshold should be inclined to the inside of the bathroom, so that the water droplets can slide smoothly to the inside of the bathroom;

2. The threshold should be the same width as the door frame, and the door frame should be the same thickness as the wall, so that there will be no big discrepancies when laying floor tiles, and the chance of breaking will be relatively reduced.

Second, the ground is waterproof.

There are many kinds of waterproofing materials, and the most commonly used one is waterproofing agent. When laying the waterproofing layer, it should be laid about 20 cm above the foot of the wall, at least not below the height of the threshold. When there is a reserved pipe on the floor, the waterproof layer also needs to cover the reserved pipe.

After the waterproofing of the floor is done and dry, it must be primed with cement mortar or protective measures immediately to prevent the waterproofing layer from breaking.

3. Floor tile laying.

There are three essentials for laying floor tiles:

1. There should be a drainage slope of about one percent, and the slope should be towards the floor drain;

2. The thickness of the floor tile joints should be consistent, and the joints of the wall tiles should be aligned;

3. When the front wall of the bathtub is made of bricks and tiles, it is best to paste the floor tiles under the wall first, and then paste the wall tiles to avoid breaks.

Fourth, wash the face countertop.

The washbasin should be selected as "full-body" (that is, the surface material of the countertop is the same as the composition and color of the internal material), and the countertop with only one layer of surface rubber shell cannot be selected because the countertop with only the surface rubber shell cannot be repaired once damaged. (To check whether the countertop is "all-over", you can use a light to shine at close range from the back, and the one that can transmit light is the "all-over" countertop). In addition, caulk must be applied to the joints of countertops and washbasins to prevent water from seeping out of the joints.

Generally, when installing the toilet, it is customary to fix the toilet with cement mortar filling, in fact, this method is wrong, after fixing the toilet with this method, the toilet can not be disassembled again, if the pipeline is seriously blocked, there is only one way to knock off the toilet. 5. Exhaust fan.

Generally, when people build houses, they don't pay much attention to bathroom ventilation equipment, and most of them just install an exhaust fan. The bad gases in the bathroom cannot be discharged from the outside, and they are still only circulating in the bathroom.

The above 5 matters are necessary to pay attention to in the construction of the bathroom, don't leave a trace of regret for your home decoration!

Anytime.

Cleaning process:

1. Wipe the glass (inside and outside).

Use glass scrapers, water wipers, non-foaming glass water, and strong neutral cleaning agents to thoroughly remove dirt, including the cleaning of window frames, the vacuuming treatment of window cracks, and the removal of some stubborn cement spots and glue spots with a glass knife. The potion contains anti-static ingredients, and the glass that has been wiped is crystal bright and not easy to get dust.

2. Comprehensive dust removal.

Use a large vacuum cleaner to suck the dust, with the dust liquid to wipe all the materials, supplies, furniture surfaces that are easy to absorb dust, and then professionally maintain them.

3. Clean the floor.

The cleaning of stone materials such as floor tiles or marble is cleaned with imported floor scrubbers with stone washing water, and then cleaned with vacuum suction machines to make the ground clean and easier to clean. The cleaning of wooden floors is to use professional floor mopping and dust pulling liquid to clean up.

4. Decontamination and disinfection of kitchen toilets.

Use neutral detergent, high-efficiency degreaser, strong toilet cleaner, and cooperate with scale removal, rust removal, disinfectant and other targeted external treatments. Heavy dirt should be cleaned with high-pressure jet.

5. Cleaning of decoration traces.

For the remaining traces of paint spots, glue spots, paint spots, cement spots and other traces after decoration, use cleaning balls and professional shovel blades, and cooperate with thinner materials and special detergents for fine cleaning treatment.

6. Waxing on the ground.

For solid wood, plastic flooring, marble, terrazzo, granite, mirror bricks, etc., a layer of protective wax is coated on its surface, which isolates air, water and dust after curing, and is anti-slip, anti-static, anti-wear, and easier to clean, so as to prolong the service life of the floor.

Waxing is divided into: solid and liquid, waxed by professionals, the wax liquid is evenly distributed, the thickness is moderate, bright and beautiful.

It is best to do a general sanitation after each decoration step, and then carry out a thorough cleaning after all the decoration is completed.