What is the reason for the deformation of the production process of the crawler shot blasting machin

There are two aspects to the deformation:

The device is deformed. The cleaned workpiece is deformed.

The above two reasons are analyzed as follows:

1. The welding quality of the equipment is poor, the steel plate is thin, and the deformation occurs with the vibration of the machine during the working process.

2. The deformation of the cleaned workpiece, the workpiece is too thin, and the deformation is produced by the impact of the steel shot, the steel shot particles are larger, and the impact force on the workpiece is large.

The chain flap of the crawler shot blasting machine is always broken, what is the reason.

Cause 1: The position of the orientation sleeve window is incorrect. 2. The inner guard plate of the shot blasting device, the directional sleeve shot wheel, and the blade damage are serious 3, and the projectile used is too small. 4. The projectile flow rate is too small.

Troubleshooting method: 1. Adjust the position of the opening of the directional sleeve socks Luyuan. 2. Check each piece in the inspection state, and replace it immediately if it is seriously worn.

3. Choose the right projectile. 4.Adjust the solenoid valve to increase the flow rate of the projectile, if the ring is insufficient, the projectile should be added.

Summary. Reasons for the cleaning effect and long time: 1. The position of the directional sleeve window is not right 2, the inner guard plate, directional sleeve, shot splitting wheel and blade of the shot blasting device are seriously worn 3, the use of projectiles is too small 4, and the projectile flow is too small Measures:

1. Adjust the position of the opening of the directional sleeve 2, check each piece, if the wear is serious, it should be replaced immediately 3, select the appropriate projectile 4, adjust the electromagnetic gate, increase the flow of the projectile, if the projectile circulation is insufficient, the projectile should be added, the screw conveyor has a low speed or stops Reason: 1There is a large debris in the auger 2

Bearing wear is severe or into debris 3Hoist belt relaxation measures: 1

Open the small access door in front of the cleaning chamber to remove debris and check if the top of the bearing is loose 2Check whether the bearing is badly worn or has a projectile (replacement) 3Adjust the tensioning device on the upper part of the hoist, tighten the belt, the hoist belt slips and causes a large friction bump sound

1. Belt relaxation 2, material blockage at the lower part of the hoist 3, hoist belt deviation measures: 1Adjust the adjustment spiral bolt of the upper part of the hoist to tighten the belt 2, open the inspection door of the lower part of the hoist, manually remove the accumulated debris, start the machine in order 3, open the maintenance cover of the upper part of the hoist, observe the direction of the belt deviation, adjust the tensioning device of the upper part of the hoist, and test the single-action while adjusting.

The chain flap of the crawler shot blasting machine is always broken, what is the reason.

Cleaning effect and long time reasons: 1, the position of the directional sleeve window is not right 2, the inner guard plate of the shot blasting device, the directional sleeve, the dust shot wheel, the blade wear is serious 3, the use of projectile is too small 4, the projectile flow is too small Measures: 1, adjust the position of the opening of the directional sleeve 2, check each piece, if the wear is serious, it should be replaced immediately 3, select the appropriate projectile 4, adjust the electromagnetic gate, increase the projectile flow, if the projectile circulation is insufficient, the projectile should be added, the screw conveyor speed is low or stop Reason:

1.There is a large debris in the auger 2Bearing wear is severe or into debris 3

Hoist belt relaxation measures: 1Open the small access door in front of the cleaning chamber to remove debris and check if the top of the bearing is loose 2

Check whether the bearing is badly worn or has a projectile (replacement) 3Adjust the tensioning device on the upper part of the hoist, tighten the belt, the hoist belt slips and causes a large friction stool rubbing sound: 1, the belt is loose 2, the lower part of the hoist material is blocked 3, and the hoist belt deviates from the measures:

1.Adjust the adjustment spiral bolt of the upper part of the hoist to tighten the belt 2, open the inspection door of the lower part of the hoist, manually clear the hidden socks to remove the accumulated debris, start the machine in order 3, open the maintenance cover of the upper part of the hoist, observe the direction of the belt deviation, adjust the tensioning device of the upper part of the hoist, and test the single-action test while adjusting.

The answer is not true. The elevator belt slips and makes a large friction and bumping sound. Causes:

The chain flap of the crawler shot blasting machine is always broken, what is the reason, is such a problem, do you understand?

Dear, I won't refund you.

I was wrong.

For large parts, it is generally necessary to carry out drum sand cleaning first, that is, the riser of the casting is cut off and then rolled in the drum, and the parts collide with each other violently when they hit the bridge in the drum, and most of the sand on the surface is removed first and then shot blasted. Shandong Jichuan will tell you about the principle of uniform shot blasting of shot blasting machine. The research shows that in terms of damage, it is much easier to eliminate tensile stress on the surface of metal materials than Xiaoqiao compressive stress, and when the surface is compressive stress, the fatigue life of the material is greatly improved, therefore, for shafts and other components that are prone to fatigue fracture, shot peening is usually used to form surface compressive stress, improve product life, in addition, metal materials are very sensitive to tensile strength, which is the reason why the tensile strength of materials is much lower than compressive strength, which is also the reason why metal materials generally use tensile strength (yield, tensile strength) to represent material properties.

The working surface of the steel plate of the car we ride on daily is strengthened with shot peening, which can significantly improve the fatigue strength of the material and prolong the life of the car. Shot blasting is to use a motor to drive the impeller body to rotate, relying on the action of centrifugal force, the diameter of the projectile (there are cast shots, cut shots, stainless steel shots, etc.) to the surface of the workpiece, so that the surface of the workpiece reaches a certain roughness, so that the workpiece becomes beautiful, or change the welding tensile stress of the workpiece to compressive stress, improve the service life of the workpiece. It is used in almost most fields of machinery, shipbuilding, auto parts, aircraft parts, guns, tank surfaces, bridges, steel structures, glass and steel plates, pipes, etc.

The care and maintenance of the crawler blast machine is the key to ensure its proper operation and extend its service life. Here are some recommended care and maintenance measures:

Regular cleaning: After use, clean the blast machine regularly to remove dust, debris, and scrap from the surface. Use appropriate tools and detergents, and take care not to damage critical parts of the machine during cleaning.

Lubrication system: It is very important to keep the lubrication system functioning properly. Regularly inspect and replace the lubricant to ensure the adequacy and quality of the oil or grease. At the same time, make sure that the pipes and connections of the lubrication system are not clogged, and that there are no oil leaks or over-lubrication at the lubrication points.

Check and replace wear parts: Regularly inspect the wear parts of the shot blasting machine, such as shot blast sheets, shot blast machine shells, tracks, etc. If worn or damaged is found, replace it promptly. The normal condition of the wear parts is crucial to the efficiency and cleaning effect of the blast machine.

Inspect and maintain the electrical tie-up system: Regularly check the working condition of the electrical system's connections, cables and switches. Ensure the safety and proper functioning of the electrical system. Regularly inspect the insulation properties of motors and electrical components, and repair or replace them if necessary.

Inspect and clean the filtration system: The blast machine is usually equipped with a filtration system to capture and filter the dust and waste generated. Regularly check the operating status of the filter, clean or replace the filter to ensure its filtration effect and normal operation.

Check and adjust the process parameters: According to the actual needs, regularly check and adjust the process parameters of the shot blasting machine, such as shot blasting speed, projection angle, selection of shot blasting materials, etc. Ensure the accuracy and adaptability of process parameters to obtain the ideal cleaning effect with coarse branches.

Repair the fault at any time: If the shot blasting machine is found to be faulty or abnormal, repair it in time. Don't ignore any unusual sounds, vibrations, leaks, or degradation in performance. Seek professional technical support or repair services as needed.

Please note that specific care and maintenance measures may vary depending on the blast machine model and manufacturer. It is advisable to refer to the operator's manual and the maintenance guide provided by the manufacturer for detailed service and maintenance requirements for your specific model.

Summary. Glad to be able to your questions.

The roller that rotates with the track can be adjusted to balance on both sides.

How to correct the track deviation of the crawler shot blasting machine.

Glad to be able to your questions. The roller that rotates with the track can be adjusted to balance on both sides.

Always go to the left and how to adjust.

The position of the inlet needs to be modified so that the inlet is kept in the middle of the lifting belt.

If you go to the left, you should keep up with your left side and relax or relax.

It should be relaxed, and if you press it up, then you will go faster to the left.

Yes! I do the same, but I always don't go in the middle.

This is a meticulous work, which needs to be adjusted a little bit, and it is a little deviated, and it is possible to deviate from the hidden envy of the stove shooting, so this is a slow infiltration to try little by little, and it is not in a hurry.

I'm relaxed on the left, now it's more to the left, what's going on.

Isn't the right way you tune it, are you going in the opposite direction? You try to go in the opposite direction.

1) The foundation construction is determined by the user: the user configures the concrete according to the local soil quality, checks the plane with a level, and after the vertical and horizontal level, it can be installed, and the anchor bolts are fastened.

2) Before leaving the factory, the cleaning room, shot blasting machine and other parts have been assembled into one, the whole machine is installed as shown in Figure 1, the upper lifting cover of the hoist should be fastened with bolts to the lower hoisting cover, and the lifting belt should be adjusted when installing the upper driving pulley bearing seat to keep it level, so as to avoid the belt deviation, and then the separator and the upper part of the hoist are fastened with bolts.

3) Install the shot gate on the separator and insert the projectile tube into the bucket behind the cleaning chamber.

4) Separator: When the separator is working normally, there should be no gap in the projectile flow curtain, if the full curtain cannot be formed, the adjusting plate should be adjusted until the full curtain is formed, and a good separation effect has been obtained.

Foshan Ronggao Machinery Equipment Co., Ltd. is a scientific and technological enterprise integrating development, design, production and sales; Mainly engaged in sandblasting, shot blasting, spraying and other surface cleaning, anti-corrosion coating and other environmental protection machinery and equipment production and sales, the main products are automatic sandblasting machine, CNC sandblasting machine, wood grinding machine, shot blasting machine, zinc blasting aluminum blasting machine, environmental protection sandblasting room, dust and exhaust gas environmental protection treatment and other environmental protection dust removal equipment.

Compared with other shot blasting machines, crawler shot blasting machine has the following advantages in metal surface cleaning:

Efficient cleaning ability: The crawler shot blasting machine adopts a combination of shot blast wheel and crawler system, which can project shot blast particles onto the metal surface with a high speed sock slippage, effectively removing rust, oxide layer, paint and dirt. It can quickly and evenly clean large areas of metal surfaces, improving work efficiency.

Comprehensive cleaning effect: Due to the recycling of blast particles in the crawler shot blasting machine, every corner of the metal surface and hard-to-reach areas can be covered to achieve comprehensive cleaning. This machine is suitable for handling workpieces with complex shapes, such as pipes, profiles, welded structures, etc.

Automatic operation: Crawler shot blasting machines are usually equipped with automatic control systems, which can realize automatic start and stop, adjust shot blasting speed and cleaning pressure and other parameters. This automation improves ease of operation and consistency, reducing human effort and operator errors.

Improved safety in the working environment: Tracked blast machines usually have a closed structure, which is able to control the dust and splash of blast particles, reducing injuries to operators and reducing environmental pollution. It can also be equipped with a dust collection system to collect and dispose of the dust generated, maintaining a clean working environment.

Errand. It is important to note that the specific advantages may vary depending on the type and design of the blast machine. When choosing the right blast machine for your specific application needs, it is advisable to discuss and learn more about it with your supplier.