If you want to DIY a mountain bike with a price of around 2000, what accessories should you buy? Ple

ATX770, aluminum alloy frame, Shimano Alivio transmission system, Manitou unilateral adjustable suspension fork, suitable for general sports riding and light off-roading, 2098's ** is still more cost-effective, and the upgrade potential of TAX770 is also relatively large, suitable for intermediate and high-end mountain bike players with a certain foundation.

The cost performance of about 2000 yuan is not too high, if it is not particularly certain, it is best to buy a whole vehicle, and the price of more than 3000 yuan can be reflected in the general situation.

In addition, a few car accessories are attached: Giant aluminum alloy frame, 500-700 yuan.

Fork: Rock Shox Dart1: about 500 yuan.

Brakes: Yanhao mechanical disc brake 380 yuan.

Frame size: As the skeleton of the whole bike, the frame determines and affects the correctness and comfort of your riding posture to the greatest extent, so choosing a suitable frame is crucial.

1.Measure the length of your thighs.

It is best to wear a cycling suit, stand on a level, hard ground, and be assisted by a person. The body is erect, with feet about 10 cm apart. Measure the distance from the top of the book to the ground with a book or other similar object flat on the crotch and applying an appropriate amount of force upwards that is less than that of the saddle

2.Measure body length.

Position the same as in step 1, measuring the distance between the clavicles from the bottom of the V-groove to the top of the book.

3.Measure arm length a

Stand horizontally, stretch your arms flat with your palms facing forward, and measure the distance from the tiger's mouth to the plane where your ribs are located.

4.Measure the width of the shoulders upright, relax the arms, and measure the width at the shoulder joint.

Each of the above dimensions is measured three times and averaged.

Based on the above data, you can get the frame size you need:

Road frame size i*

Mountain bike frame size (i*inches).

Stem length [(t+a) 2+x]-et

G Road Bike x 4;Mountain x 8;et effective top tube length (the "o" in the first image).

The length of the crank that you fit: Leg length range (cm) crank length.

65cm - 70cm 165mm

71cm - 76cm 170mm

79cm - 81cm

82cm - 90cm 175mm

Width of the bend handlebar: (The width of the bend bar refers to the length from center to center).

Shoulder width range s width cm width

38cm 38 – 40

39cm 40

40cm 40

41cm 40 – 42

42cm 42

43cm 42 44 --- this paragraph is taken from.

2000 is not recommended to assemble your own car, especially for novices, buy an entry-level car first and then take your time. Recommend the Duke of Merida RS.

The Giant ATX770 can be compared with the Duke of Merida before the price increases, so forget about it now.

There are a few important points to keep in mind with mountain collocation, 1Whether the combination of the front shifting and the large crankset is reasonable.

2.Whether the rear cassette and rear transmission are properly matched.

3.Whether the combination of the rear cassette and the large crankset is reasonable.

There is also the RC of the frame, and if the RC is too short, it will affect the shifting.

This ** is recommended to buy a full vehicle. Nothing can be loaded, they are all low-end, and it is very unpleasant to ride.

Frame, fork, handlebar set three-piece set, shifting, brakes, cushions, pedals, wire tubes, brake handles, wheels, inner and outer tubes, if a novice recommends going to a bicycle shop to assemble, otherwise you won't install the accessories yourself.

Frame, large kit (you can buy it separately), wheels, tubes, forks, saddles, seat tubes, scales, wrist sets, grips, pedals.

Frame, Bowl, Fork, Handlebar, Tube, Seatpost, Clamp, Grip, Brake, Crankset, Bottom Plate, Pedal, Front Deraille, Rear Deraillement, Finger Pipe, Core, Flywheel (Tallon), Wheel, Inner Tube, Outer Tyre, Tire Pad (Wheels are generally bred), and there are many parts, Cup holders, etc. It depends on what car is assembled, I also like DIY, 1159800618 have time to communicate.

First of all, you need to buy the following accessories for the car itself:

Frame (usually with a bowl and tail hook), handlebars, stems, grips, finger dials, brake handles, forks, wheels (including hubs, quick releases, spokes, rims, tire pads), front derailleurs, rear derailleurs, wire pipes, cranksets, chains, flywheels, inner tubes, outer tires, bottom brackets, seatposts, saddles, pedals.

The tools that are installed afterwards are not required if they are installed in a physical store. Self-installation requires a set of hexagon sockets, bottom brackets, bowl set installation tools, open-end wrenches, and core smashing tools.