How to connect the motor of the corn thresher? Corn thresher motor, how to wire 5 roots

1. Start the motor without any load when the motor is empty, and then add corn on the cob when the motor speed reaches the normal speed.

2. When the motor is working normally, the corn cob should be filled evenly, and the load should not be filled suddenly, so as not to get stuck in the machine and cause the loss of burning the motor.

This is a three-wire connection, just see the manual to connect it, see that it is a neutral line of fire, ground wire, clear can be connected to use.

Although the society is developing rapidly, the working environment of the large corn thresher is very bad, and the safety awareness of the operators is poor, so here is the above figure as an example to summarize the safety operation procedures of the large corn thresher and share it with you:

1. Before working, the operator must wear glasses and masks, and tie the cuffs and collar tightly;

2. Start-up sequence: first open the conveyor, then open the main machine, and finally open the climber;

3. When starting up, it is necessary to ensure that each single machine is forward rotation;

4. In the boot state, it is good to see that there are no bricks, stones and other hard objects entering the host, so as not to damage the host;

5. When feeding, it must be fed evenly, and it is forbidden to feed the ground in strands to prevent choking (especially wet corn);

6. Pay attention to whether the rotating parts are loose when starting the machine to prevent flying out and hurting people;

8. Shutdown sequence: first turn off the climber, then turn off the host, and finally turn off the conveyor.

Corn thresher motor, how to wire 5 roots

Corn thresher motor, 5 how to wire five wires of the motor wiring method: the motor has 5 lines, the color alone does not dare to completely judge which three are speed regulation, it is recommended that it is best to use a multimeter to measure the resistance between the wire heads, the smallest resistance is high speed, followed by medium speed and low speed, the largest resistance capacitor. Measure which two lines have the largest resistance between the 5 lines, the capacitance is on the two lines, and the remaining 3 are variable gears, the power supply is connected to one end of the capacitor and the variable speed is in a difficult gear, if the motor is reversed, then the other end of the capacitor is changed.

Dress up red, blue, and white as speed regulation. The brown one is connected to the capacitor, and the black one is connected to the other capacitor and the power supply. Red, white and blue are fast, medium and slow, and one of these three is connected to the power supply.

The brown one is connected to one of the capacitors, and the black one is connected to the other capacitor and the power supply. First of all, a wire of the plug is connected to the gear switch line of speed regulation, then the red, white and blue three wires are connected to each gear in turn, and finally a power cord can be connected on the 0 gear.

Summary. 1.Causes of Drum Blockage:

Feeding too much corn on the cob; The rotational speed is lower. Solution: Clean up the blockage (such as stones, sticks and other hard objects, etc.), and then appropriately reduce the amount of corn cob feeding and achieve uniform feeding.

2.Reasons for uncleanness: too much corn on the cob; The threshing gap is too large; The drum speed is low.

Solution: Appropriately reduce the amount of corn cob feeding; Check and adjust the belt tension, and then adjust the small corn threshing gap; If it is caused by belt wear, it must be repaired or replaced in time. 3.

Reasons for the high crushing rate: uneven thickness of feeding corn cobs; Small threshing gap; High drum speed; The corn on the cob is too dry. Workaround:

Make the corn cob evenly fed; Appropriately adjust the threshing gap or replace the pulley to reduce the drum speed. 4.Reasons for poor feeding:

Feed the corn on the cob too thick; Loose transmission belt; Conveyor belt slippage. Solution: Reduce the amount of feeding; Check and adjust the tension of the transmission belt and the tension of the conveyor belt.

5.Causes of large grain loss: strong fan wind; The opening of the sieve hole is small and the separation is poor; The amount of corn cob fed is too large, and the entrained kernels are large; The sieve surface is clogged.

Solution: Adjust the air regulator to reduce the air intake; Adjust the opening of the sieve hole; Appropriately reduce the amount of feeding; If the sieve surface is blocked, the blockage can be removed. 6.

Reasons for low cleanliness: small air volume; The sieve hole is open.

1.Cause of drum blockage: Feeding too much corn on the cob; The rotational speed is lower.

Solution: Clean up the blockage (such as stones, sticks and other hard objects, etc.), and then appropriately reduce the amount of corn cob feeding and achieve uniform feeding. 2.

Reasons for uncleanness: too much corn on the cob; The threshing gap is too large; The drum speed is low. Workaround:

appropriately reduce the amount of corn cob feeding; Check and adjust the belt tension, and then adjust the threshing gap of the small corn hidden chain; If it is caused by belt wear, it must be repaired or replaced in time. 3.Reasons for the high crushing rate:

uneven thickness of the corn cob fed; Small threshing gap; High drum speed; The corn on the cob is too dry. Solution: Make the corn cob evenly fed; Appropriately adjust the threshing gap or replace the pulley to reduce the drum speed.

4.Poor feeding causes: Feeding corn cobs is too thick; Loose transmission belt; Conveyor belt slippage.

Solution: Reduce the amount of feeding; Check and adjust the tension of the transmission belt and the tension of the conveyor belt. 5.

Causes of large grain loss: strong fan wind; The opening of the sieve hole is small and the separation is poor; The amount of corn cob fed is too large, and the entrained kernels are large; The sieve surface is blocked and sold. Workaround:

Adjust the wind regulator to reduce the air intake; Adjust the opening of the sieve hole; Appropriately reduce the amount of feeding; If the sieve surface is blocked, the blockage can be removed. 6.Reasons for low cleanliness:

Small air volume; The sieve hole is open.

We recommend that you troubleshoot the problem from the following aspects.

The small corn thresher is blocked under the bud rice stick.

I checked it. It's just blocked at the bottom.

There are other reasons.

If you check it, you can deal with it on my above, dear.

Or can you describe other problems as well, and I'll show you.

Summary. 1. Flatten the four feet of the equipment to ensure stability and firmness. to reduce vibration.

2. If the motor is used as power, be sure to check whether the power cord is firmly connected, tightly sealed and installed with the ground wire.

3. Feed the corn cob continuously and evenly, and the feeding amount should be appropriate. If the feeding is intermittent, it will affect the production efficiency, and too much feeding will cause the machine to jam and overload, resulting in burning of the motor and damage to the equipment.

4. The water content of the threshed corn cob shall not exceed 20%, and the water content is too high to achieve the normal threshing effect.

5. Before the end of the work, the input corn cob should be completely cleaned and discharged, and the empty load should be stopped, and it is forbidden to stop with load.

Corn thresher motor, how to wire 5 roots

1. Flatten the four feet of the lap chain equipment to ensure stability and firmness. to reduce vibration. 2. If the motor is used as power, be sure to check whether the power cord is firmly connected, tightly sealed and installed with the ground wire.

3. Feed the corn cob continuously and evenly, and the feeding amount should be appropriate. If the feeding is intermittent, it will affect the production efficiency, and too much feeding will cause the machine to jam and overload, resulting in burning of the motor and damage to the equipment. 4. The water content of the threshed corn cob shall not exceed 20%, and the water content is too high to achieve the normal threshing effect.

5. Before the end of the work, the input corn cob should be completely removed and discharged from the shirt after the empty load is stopped, and it is forbidden to stop with load.

If those two pieces are connected horizontally, you can take it off and connect it vertically, and if you dismantle the foundation vertically, you can change it horizontally. Pay attention to the ground wire, safety first. Good luck!

Summary. <>

Hello! Dear, I'm glad to have your question, help you find out, corn thresher motor, 5 wiring methods: corn thresher motor, 5 how to wire five wires of the motor wiring method:

The motor has 5 lines, just by the color does not dare to completely judge which three is the speed regulation, it is recommended that it is best to use a multimeter to measure the resistance between the wires, the smallest resistance is high speed, followed by medium speed and low speed, the largest resistance capacitor. Measure which two lines have the largest resistance between the 5 wires, the capacitance is on the two lines, and the remaining 3 are the variable gears, and the power supply can be connected to one end of the capacitor and the variable gear.

Corn thresher motor, how to wire 5 roots

Hello! Dear, I'm glad to have your question, help you find out, corn thresher motor, 5 wiring methods: corn thresher motor, 5 how to wire five wires of the motor wiring method:

The motor has 5 lines, just by the color does not dare to completely judge which three is the speed regulation, it is recommended that it is best to use a multimeter to measure the resistance between the wires, the smallest resistance is high speed, followed by medium speed and low speed, the largest resistance capacitor. The forest bucket and pin vertically measure which two lines have the largest resistance between the 5 lines, the capacitance is on the two lines, and the remaining 3 are the variable gears, and the power supply is connected to the capacitor at this trace end and the variable gear.

Pro, corn thresher motor, 5 wiring method: corn thresher motor, 5 how to wire five wires of the motor wiring method: the motor has 5 lines, just by the color does not dare to completely judge which three are speed regulation, it is recommended that it is best to use a multimeter to measure the resistance between the wires, the smallest resistance is high speed, followed by medium speed and low speed, the largest resistance of the power connection difference.

Measure which two lines have the largest resistance between the 5 rolling rock lines, the capacitance is on the two lines, and the remaining 3 are the variable speed gears, and the power supply can be connected to one end of the capacitor and the variable speed Qing vertical gear.

If the motor is reversed, the other end of the capacitor is reconnected. Red, blue, and white are speed controls. The brown one is connected to the capacitor, and the black one is connected to the other capacitor and the power supply.

Red, white and blue are fast, medium and slow, and one of these three is connected to the power supply. The brown one is connected to one of the capacitors, and the black one is connected to the other capacitor and the power supply. First of all, Fuhe connects a wire of the plug to the gear switch line of speed regulation, and then connects the red, white and blue three wires in turn on each gear, and connects a missing section of the power cord on the 0 gear after the most combustion.