Which is better, a badminton racket that is formed twice or a badminton racket that is molded once

There is no doubt that a racket with 2 times of molding is better!! Overmolding technology is generally used for high-grade feather rackets.

That is, the frame and the barrel are forged separately and finally connected together. But after the lacquer treatment, these traces of connection are not visible. Advantages of overmolding feather rackets:

Because the frame and the pole can be made separately, the pole can be woven and bonded with multiple layers of carbon gauze at different angles, and the elasticity, toughness, torsional resistance, hardness and other parameters of the pole can be controlled according to the weaving angle of different layers of carbon gauze. The production of the frame does not need to use such a complicated weaving method, only requires hardness. The market price of the feather racket made by the secondary molding process is generally more than 100 yuan.

A molding process refers to the head and frame with the same strand of carbon gauze wrapped around the plastic tube at one time, the technology is simple, can be produced in large quantities in a short time, the disadvantage is the poor torsion resistance, if the user has a certain level of technology, with the wrist, finger force quickly, then in the high-speed flat pumping, catch, will feel the poor torsion resistance of the racket has an obvious sense of viscosity, the ball is slow.

In general, a badminton racket that is formed twice is better than a badminton racket that is formed in a single time. Here's a comparison:

1.Badminton rackets that are formed twice are generally forged separately from the frame and shaft, and finally joined together. The badminton racket made by this process has better ball control performance and landing accuracy.

The junction between the frame and the barrel is made using a special technique, and it is so strong that I have never heard of a double-molded racket breaking from there. On the other hand, the badminton racket with one-time molding is relatively simple and can be mass-produced in a short period of time, but the torsion resistance is poor.

2.The badminton racket that is formed twice can control the elasticity, toughness, torsion resistance and hardness of the racket according to the weaving angle of different layers of carbon gauze. The badminton rackets that are formed in one pass perform worse in these aspects.

To sum up, the 2-shaped badminton racket is comparatively better in terms of performance and durability, and is more favored by badminton enthusiasts and professional players.

These are two different manufacturing processes, and the quality of the overmolding is higher.

One-time molding refers to the manufacture of the barrel and frame together, and the toughness of such a racket is relatively poor. Overmolding is a racket making process, which refers to the following: the racket is first made into a racket shaft, and then the racket frame is made through the model after its strength and hardness are tested to meet the standard.

Because the racket and frame are manufactured separately, the weight distribution of the racket is well controlled, and the elasticity, toughness, torsional resistance, hardness and other indicators of the whole racket have also been greatly improved.

Overmolding technology is generally used for high-end feather rackets, that is, the frame and shaft are forged separately and finally joined together, but after the lacquer treatment, you will not be able to see these connection marks.

The advantage of the overmolding feather racket is precisely because the frame and the racket can be made separately, and the pole can be woven and bonded with multiple layers of carbon gauze at different angles, and the elasticity, toughness, torsion resistance, hardness and other parameters of the racket can be controlled according to the weaving angle of the carbon gauze with different layers. The production of the frame does not have to use such a complex weaving method, only requires hardness, so the process is relatively simple, and the feather racket is made by the secondary molding process.

A molding process refers to the head and frame with the same strand of carbon gauze wrapped around the plastic tube at one time, the technology is simple, can be produced in large quantities in a short time, the disadvantage is the poor torsion resistance, if the user has a certain level of technology, with the wrist, finger force quickly, then in the high-speed flat pumping, catch, will feel the poor torsion resistance of the racket has an obvious sense of viscosity, the ball is slow.

Upstairs is not right! The one-time molding process refers to the one-time molding of the racket head and the racket with the same strand of carbon gauze around the plastic tube, the technology is simple, and it can be mass-produced in a short period of time.

The advantage of the secondary molding feather racket is precisely because the frame and the racket stick can be made separately The racket can be woven and bonded at different angles according to the weaving angle of different layers of carbon gauze, respectively, the elasticity, toughness, torsional resistance, hardness and other parameters of the racket stick can be controlled, so it is better than a one-time molding, and it is much higher.

The one-time molding technology refers to the use of whole beat blowing for the head and frame, which is easy to make the left and right walls of the stick and frame uneven, and the stability is relatively poor.

Overmolding technology means that the head and frame are blown separately to make the material more evenly distributed, so the stability of the beat is better.

It must be a sturdiness of the first molding.

The acquaintance of the secondary molding is more than the primary molding.

Badminton rackets are imitation rackets and fakes if they are mentioned as primary forming rackets and secondary forming rackets. In fact, the quality is the same, there is no difference, it's just a gimmick.

The primary forming racket is that the frame and the rod are manufactured at one time, and the secondary molding is produced separately and then assembled, and the shock absorption effect of the secondary forming racket is better, and the performance of the middle rod is also significantly improved.

Badminton rackets are generally composed of a racket head, a racket shaft, a racket handle, and a joint between the racket frame and the racket. The length of a racket is not more than 68 cm, of which the length of the racket handle and the racket shaft is not more than 42 cm, the length of the racket frame is not more than 25 cm, and the width is 20 cm.

Upstairs is not right! The one-time molding process refers to the one-time molding of the racket head and the racket with the same strand of carbon gauze around the plastic tube, the technology is simple, and it can be mass-produced in a short period of time. The advantage of the secondary molding feather racket is precisely because the frame and the racket stick can be made separately The racket can be woven and bonded at different angles according to the weaving angle of different layers of carbon gauze, respectively, the elasticity, toughness, torsional resistance, hardness and other parameters of the racket stick can be controlled, so it is better than a one-time molding, and it is much higher.

The one-time molding is stronger than the two-molding! One-time molding means that the head and rod are one! The one that is twice split is one! Of course, the conjoined ones are good! The head and body will not be separated or deformed!

Upstairs mistake, the overmolded racket is better than the one-time molding, and it is more delicate and complex in terms of process, because I sell badminton rackets, so I understand this.

The acquaintance of the secondary molding is more than the primary molding.

The one-time molding is stronger than the two-molding! One-time molding means that the head and rod are one! The one that is twice split is one! Of course, the conjoined ones are good! The head and body will not be separated or deformed!

The acquaintance of the secondary molding is more than the primary molding.

Upstairs is not right! The one-time molding process refers to the one-time molding of the racket head and the racket with the same strand of carbon gauze around the plastic tube, the technology is simple, and it can be mass-produced in a short period of time. The advantage of the secondary molding feather racket is precisely because the frame and the racket stick can be made separately The racket can be woven and bonded at different angles according to the weaving angle of different layers of carbon gauze, respectively, the elasticity, toughness, torsional resistance, hardness and other parameters of the racket stick can be controlled, so it is better than a one-time molding, and it is much higher.