How is the small windmill made?

Tools Materials: scissors, cardboard, glue sticks.

1. Prepare a square cardboard. It must be square paper, and the paper must not be too soft, otherwise it will not be shaped.

2. Fold the square paper in half into a triangle.

Fold it in half again, this step must pay attention to pressing out the crease, and the next step is to rely on the crease to complete.

3. After opening, you will see two obvious creases, take out the scissors and cut them inside according to the creases, one centimeter away from the center, do not scissors in the center.

4. Apply a glue stick to the center point, you can apply more here to avoid falling off.

5. Pick up the cut corner and stick it to the center point, be sure to stick it tightly, and glue all the four corners to the center point in turn.

6. In this way, the big windmill.

That's it. <>

1. Materials: cardboard, scissors.

Second, the specific steps:

1. Cut a square piece of origami paper in any color.

2. Fold it in half along the dotted line.

3. Fold it in half along the other diagonal.

4. Along the crease, cut the four diagonal corners about 2 3.

<>6. After the four corners are folded back, they are glued and glued, and the windmill is completed.

Preparation tools: a pair of scissors, a roll of double-sided tape, a straw, a square piece of cardboard, and a thumbtack.

Steps. First, prepare all the tools needed to make a windmill. See the image below.

Steps. Second, the four corners of the colored paper are folded in two, and then cut along the folded line with scissors, leaving about one centimeter in the middle do not cut, as shown in the figure below.

Steps. 3. After cutting, cut a few small pieces of double-sided tape and stick them to the position in the figure below. See the image below.

Steps. Fourth, first fold a corner inside, do not flatten, stick together, as shown in the figure below.

Steps. Fifth, then do the other corner in the same way as above, as shown in the figure below.

Steps. 6. Paste all 4 corners in the center. See the image below.

Steps. 7. Find a pushpin to pass through the middle of the windmill and the straw. See the image below.

Steps. 8. Use a pushpin to fix the windmill on the straw, and the windmill that will turn is ready. See the image below.

How to make a windmillThe materials that need to be prepared are colored cardboard, scissors, and glue, and the method is as follows:

1. Directly cut the colored cardboard into a square shape.

2. Fold the square paper in two along the diagonal.

3. Cut the folded triangle along the line, but leave a distance of about 2 to 4 cm wide in the center.

4. Continue to glue the four corner septum blocks to the center of the square.

5. In this way, you will get the result shown in the diagram to make a windmill.

Two. Summary: Cut a piece of A4 paper into three small segments, splice the three small segments together, and finally tighten the strip of paper, and the small windmill is completed.

Tools Raw materials: 1 piece of color cardboard; A knife or ruler.

Method Steps:

1. Choose a piece of color cardboard or A4 paper.

2. Fold 3 strips of paper 1 cm wide along the lower end of the paper in turn.

3. Use a knife or ruler to cut out these three strips of paper separately.

4. Fold each note in half. Then, gently put them together as illustrated.

<> precautions: 1. Try to choose a harder color cardboard for the paper, which makes the paper windmill rotate better.

2. Pay attention to the order of the three paper strips, which is regular, otherwise it is not easy to make.

1. Cut into squares. First, use scissors or paper cutters to cut the paper into 4 squares, one large and three small (the large square paper directly determines the size of the windmill, and the length of the three small sides is between 1-2cm).

2. Extend the diagonal tangent. Cut the large Zhengsen oak square paper diagonally, do not cut through the middle part, and cut all 4 corners.

3. Bend and cut the surface. Bend the right part of the corner of the big square just cut to the middle, and the left part of the spike does not move, 4. Reinforcement. Glue a small square to the middle of the fold of the large square and reinforce it.

5. Sticky. Glue all the freshly bent corners of the big square to a small square block.

6. Punching. Glue another small square to it and find another nail to pass through the middle of the three small square blocks. Just make a hole.

7. The nail passes through the hole. Finally, use a small nail to pass through the hole that has just been punched on the side. The little windmill is done. Pinch the nail like in the picture below, then blow towards the position of the windmill and it will spin!

Windmills can be said to be one of the most popular toys when you were a child, and today you will be taught to make your own small windmills, and it is not good to put them on the table? And it's easy to learn, all you need is a paper clip and a small piece of paper.

Cut the piece of paper into the shape shown in the lead pick-up diagram.

<> cut a small strip of paper and stick it on a paper clip.

Attach the small windmill to the paper clip.

Origami has a long history and a large number of enthusiasts in our country, especially loved by children and teenagers. It is a child's nature to play, how to educate children in the process of playing? Origami provides a good way in this regard, and children can improve their hand-brain coordination and creativity in the process of origami. Branches.

First of all, we need to prepare the necessary tools: scissors, colored paper, chopsticks, thumbtacks, erasers.

Here's how it works:

1. Take out the prepared colored paper and fold it twice along the diagonal of the square colored paper and then again.

Second, then along the crease of the square colored paper, use scissors to cut out the four edges, but the main thing is not to cut it.

3. After Sui Zhaozhou, fix the cut colored paper together with nails, and then dig a hole in the eraser where disposable chopsticks can be inserted, and install the wooden stick guess and the eraser together.

Fourth, finally fix the fixed colored paper and small wooden sticks together, so that a small handmade windmill is done.

<> "Little Windmill Creative Handmade Painting."

Cut the crease of the stove to the middle according to the square dress, paste and fix the center point, fix the center with clay, paste the handle, and simply decorate the spine picture.