What should I do if the size changes after CAD chamfering?

I know what you mean, that is, if you actually measure the parts you want to draw, it should be 40mm high, of course, the actual parts are chamfered, if you are surveying, then you need to draw the center line first, and then draw each side, when measuring the distance between them, you should avoid the inverted corners, and then use the center line to offset, and then let them extend the intersection, and then use the cutting tool to cut off the extra parts, and then chamfer the acute corners, so that there is no problem. Finally, the dotted line is used to express the intersection of the poured acute angle extension, and the starting point of the label should be the acute angle dashed line part, so that the value of the sub-label should be greater than 40mm.

Silly !! The dimensions change after chamfering because your dimension snap point is exactly on the endpoint. This way, when you chamfer, it will automatically track to the reduced position, so the change will occur.

Enlarge the endpoint position of the dimension line and you'll see it.

Pulling the start of the dimension line to the line of the measuring surface returns to the normal size. The next time you want to chamfer the annotation, don't click on the corner, and there will be no such problem in the middle of the selection paragraph.

If the height of the chamfer is reduced from 40 to 36, then the next time you draw, you should draw it to 44 first.

Some simple rounded corners can be solved by "drawing circles". Then use the trim to remove the unwanted lines and semicircles.

Use it first"Annotations"Take a look at the height after chamfering, how much worse than 40mm, and then draw as much more the height next time you redraw it.

That's because the size of the corner you want to chamfer is too large, for example, a 10*10 rectangle, inverted c15, it will definitely not be poured.

It's also possible that the line is spline, it looks like a straight line, and I've seen it many times that the splines can't be chamfered between each other.

This kind of problem does exist! If the angle of the acute angle (within tolerance) can be varied, stretch it some!

Material Tools: CAD

1. Open the CAD software, enter the CAD operation interface 2, open the CAD software, find the rectangle tool 3 in the toolbox on the left, use the rectangle tool to draw a rectangle in the drawing area, and then find the chamfer command on the right side 4, select the chamfer command, enter d command 5 in the prompt input box, press the enter key after entering the d command to prompt us to enter the distance of the chamfer, and enter 100 in the input box

6. After entering the distance, press the enter key and then the distance 7 of the second straight line chamfer in the input box, after entering the distance of the second chamfer, press the enter key to prompt us to select the first chamfered straight line 8, after selecting the first chamfered straight line, prompt us to select the second chamfered straight line 9, after selecting the second chamfered straight line, we get the chamfer 10, press the space bar to continue to perform the chamfering operation, and the other corners are also chamfered, and the final effect is shown in the figure:

How to chamfer CAD, the operation method is as follows. 1. First of all, open the CAD software in the computer, enter the software, and create your own drawings, as shown in the figure below.

2. Then click the chamfer command, as shown in the figure below.

3. Enter d in the command bar, press Enter, and then enter the size of the chamfer to be entered, as shown in the figure below.

4. Then select the straight line that needs to be chamfered, and the chamfer will be successfully done, as shown in the figure below, it will be completed.

1.To the fillet and enter "f.""r Enter the fillet radius to select the first object and the second object OK

2.Chamfer, enter cha d Enter the distance between the first line and the second line Select the first line and the second line OK

The chamfer angle can also be carried out according to the angle, and the test will be fully understood.

Select chamfer in the menu, prompt to select the first straight line or (distance d, angle a...).For example, press the selected distance d (refers to the distance from the intersection of the two lines to be chamfered), prompt to select the first chamfer distance, for example, the first line is the horizontal horizontal line in the cross line, d refers to the distance from the original intersection point in the x direction of the starting point of the chamfer, for example, enter 10 (the original default 0); Prompt to select the second chamfer distance, for example, the second line is to select the vertical vertical line in the intersection line, which refers to the distance from the original intersection point in the y direction of the starting point of the chamfer, for example, enter 10 (the original default 0); Prompt to select the first line, you click on the horizontal line in the X direction; When prompted to select the second line, you click on the vertical line in the Y direction. So we get a chamfer of x,y(10,10).

For example, if you select the angle a, you will prompt the chamfer length of the first straight line (similar to the above, if you select the x-direction line, it refers to the distance between the horizontal and the intersection point), for example, enter 10 (the original default is 0); Prompt the angle of the first straight line, for example, write 45, which is the angle of 45°; Prompt to select the first line, click on the horizontal line; Prompt to select the second line, click the vertical line. This results in a chamfer of 10,45° from the original intersection.

Others are similar.

CAD chamfering tool The two cases of chamfering are angle and distance Do you know how to use it?

In the modification, click on the chamfer, and then click on the two lines that need to be chamfered, which must be straight lines.

Tools Raw materials.

Auto CAD2004 computer.

Method steps.

1. First of all, open the software and enter the "Auto CAD Classic Interface".

2. Directly enter the formula "rec" and press the spacebar.

3. Enter the new interface, enter "C" in the input box and press the space.

4. A prompt pops up, enter "3".

5. Then enter "3".

6. Drag the mouse at the position where you want to insert the chamfer, and the chamfer is drawn.

The operation steps of chamfering in Haochen CAD:After opening the drawing in Haochen CAD software, enter the CAD chamfer shortcut command in the command line: CHA, press the enter key to confirm, and then select the first straight line according to the command line prompts, and press the enter key to confirm; Then select the second line or hold down the shift key to select the line to which you want to apply the corner point, and press enter to confirm.

As shown in the figure below:

In addition to the CAD chamfering command can be called by CAD shortcut command, the CAD chamfering command can also be called by the menu bar or toolbar. The specific steps are as follows:

Toolbar: [Common] - [Modify] - [Chamfer]. As shown in the figure below:

Menu item: [Modify] - [Chamfer]. As shown in the figure below:

1. Select the chamfer tool in the toolbar, or you can enter the command, the CAD chamfer shortcut is "CHA".

2. Select the chamfering tool and enter "D" (set the chamfering distance), and then press Enter to confirm.

3. Enter the first chamfer distance and press the enter key to confirm.

4. Enter the second chamfering distance and press the enter key to confirm.

5, then click the first chamfer distance and the second chamfer distance in the graph.

6. At this time, the CAD chamfer has been drawn.

Learn how to use CAD2014 chamfers and rounds in 15 minutes.

Draw two straight lines, open the Modify command, select the Chamfer command, then type d Press Enter, enter the distance of the first edge, press Enter, and then enter the distance of the second edge Press Enter.

Click the chamfer command, press d again, enter the chamfer length of the first edge, then enter the chamfer length of the second edge, and then click the corresponding 2 chamfer edges to form a chamfer

Rectangle tool Enter "c" on the keyboard and press Enter for chamfer distance.

In addition, the virtual machine group is on the product**, which is super cheap.

After the graphic is drawn, click on the special chamfer button.

cha + enter, d enter, enter the chamfer value.

The specific steps of CAD chamfering operation are as follows:Tools: ASUS Zenbook X Dual Screen, Windows 10.

1. Turn on the computer, enter the CAD software, and draw two straight lines in the interface.

2. Draw two straight lines and click the modify chamfer icon in the toolbox.

3. When the mouse becomes a square back box, select the first straight line, press the letter d and press enter.

4. Enter the distance of the chamfer in the pop-up box, then select the second line and enter the distance of the chamfer, and press the enter key.

Haochen CAD chamfer drawing steps:After opening Haochen CAD software, first draw a rectangle in the drawing area.

Then enter the CAD chamfer shortcut: CHA, press the enter key to confirm; When prompted to select the first line or [Discard (u) Polyline (p) Distance (d) Angle (a) Trim (t) Method (e) Multiple (m)], type: a, press Enter to confirm; Then, according to the command line prompts, specify the chamfer length of the first line and the chamfer angle of the first line. After the setting is complete, select two intersecting lines in the diagram to complete the chamfer.

Click the chamfer command in CAD and enter the letter D, then set the distance of the point and click OK to chamfer, the specific operation is as follows:

Tools Raw materials: Lenovo Y7000P, Windows10, AutoCAD2022

1. Click the chamfer function.

Go to the CAD software and click Modify at the top of the page, and then click on the chamfer function on the page.

2. Enter the chamfer distance.

Then enter command d in the command box below, and then enter the chamfer distance for the first point.

3. Tap enter to confirm.

Enter the chamfer distance of the second point, and then hit enter to perform the chamfer operation.

The CAD chamfer dimensioning method is as follows:

Open CAD, enter the command dim in the command bar, and press the spacebar to OK. After entering the command, type L again and press the spacebar to make sure you are not shouting. Once you've decided on the l command, tap a few points if you need them, and then press the spacebar to confirm.

Once you have drawn the chamfer, enter the callout text. After entering the annotation text, press the enter key directly to confirm, and the chamfer annotation is done.

The CAD is detailed as follows:

CAD drawing is a kind of drawing software, designers use computers and their graphics equipment to carry out design work, CAD drawing includes floor plan, isometric drawing and three-dimensional drawing, widely used in architectural design, mechanical design, civil construction, etc. CAD drawing software is the most popular CAD software package in the field of computeraided design (CAD).

It is a visual drawing software shortcut that can be commanded and manipulated in a variety of ways, such as menu options and tool buttons.

It has a wealth of drawing and drawing assistance functions. This software is powerful, easy to use, reasonable, widely used in machinery, construction, home, textile and many other industries at home and abroad, with a large user base.

The method of CAD chamfering dimensioning is as followsTools: HP Battle 66, Windows 10, CAXA CAD2016.

1. Open CAD.

2. Click the "Chamfer Label" icon in the "Labeling" section of the menu bar below.

3. At this time, the input parameter column will appear in the lower left corner of the software window.

4. Select the appropriate parameter into the box after "3" in the input parameter field in the lower left corner of the window, for example, "perpendicular to the chamfer line".

<>6. Move the mouse cursor to the appropriate position of the drawing standard, and click the left mouse button to determine its datum point.

1. First of all, let's open the software, enter the "Auto CAD Classic" interface, and prepare the drawing.

2. Now to open the state of chamfering, method 1: directly enter the "cha" on the keyboard and then the space bar to determine; Method 2: Click the "Chamfer" button on the right toolbar.

3. For the chamfer value, we need to enter two, and we can enter different chamfer distances and different corners on the two straight lines. Now we enter the chamfer state, and the spacebar OK after typing "d" on the keyboard.

4. Now enter the state of chamfer distance, the drawing area prompts to specify the first chamfer distance, here the input is "3", and then press the spacebar to determine.

5. Now specify the second chamfer distance, in order to distinguish the angle of the same value from the rectangular chamfer, the input here is "5", and the space is still determined.

6. After that, you will start to select, you need to chamfer two straight lines, after you select one here, the straight line will become a dashed line (selected state).

7. After selecting the second straight line, you can complete the chamfer, here you can see the distance from the chamfer, the horizontal distance is "5", and the vertical distance is "3".

8. Here comes with a practical tip, which is to keep the straight line before the chamfer, and after entering the chamfer state, enter the space after "t" in the command branch of the prompt bar.