How do you place the guitar strings? In which direction the guitar tuning pitch goes

Guitar strings should be placed as follows:

1.Start by placing the piano in a comfortable place where it can be operated comfortably, with the headstock raised for easy knobs.

2.Then, in the order of 6 strings to 1 string, insert the winder into the twist and grasp the handle and turn it, or slowly twist the string with your hand until the strings are loose, and remove the strings in turn.

3.Use the winder to pull out the latch, wipe the piano with a cloth, take out the new string, bend the string at an angle of 135 degrees about a centimeter from the tail end, and then insert the latch.

4.Twist the twist clockwise so that the hole through the string is parallel to the pillow, and then wrap around the string.

5.Use the stringer again, be sure to hold down the strings on the pillow, and then trim off the excess with a wire cutter, and finally tune it.

Please note that when changing strings, you should first change the 6 strings, turn the counterclockwise knob so that the hole is roughly 45 degrees, pass through the 6 strings, let the end exceed the knob hole 2-3 mm, and pull the string tight; Continue to twist the knob counterclockwise until it is tight, and be sure to tighten the string with your right hand as you rotate with your left hand. For bass strings, 2-3 turns is best, and the same is true for strings, leaving 3 cm for about 6 cm more.

The strings of folk guitars are generally as follows: 123 strings are tied clockwise (456 strings counterclockwise) to the twist, and then passed into the hole about 3 times. Tuning:

123 strings) tighten the strings clockwise, raising the pitch and decreasing the notch. (456 strings) tightened counterclockwise, the pitch rises, and vice versa. If you want to tune the standard tone, you can tune it according to the piano, press and hold the 2 strings and 1 fret for the C tone 1, which is the same frequency as the **c tone of the piano, and tune it to the same by hearing, and then tune the other strings according to the relationship between the six strings of the guitar.

The sound of the 1st string is the same as that of the 2nd string and the 5th fret, the 2nd string is the same as the 3rd string and the 4th fret, the 3rd string is the same as the 4th fret and the 4th string 5th fret, the 4th string is the same as the 5th fret of the 5th string, and the 5th string is the same as the 6th string and the 5th fret (disadvantages: poor hearing and inaccurate tuning). Some tunes have a special tuning, so that's a different tune.

But it would be better if there was a tuner, which could directly help make up for the shortcomings of poor hearing.

The direction should be adjusted according to the chord pitch selection. If the string spacing is too low, the wrench should be turned in the direction of 6 strings; If the string spacing is too high, turn the wrench in the direction of the 1st string. The string pitch refers to the distance from the string (bottom) to the frets (top), the normal neck is a straight line, and if the guitar neck is curved, the string pitch needs to be tuned.

Check whether the height of the strings from the 1st fret and the 12th fret is at the appropriate height when the string is open: the standard range of 1st fret is between 1mm and 3mm for 1st string and 12th fret at 1st string; The standard range of 6 strings and 1 fret is between, and the standard range of 6 strings and 12 frets is between.

Neck adjustment is relatively easy to operate, you can insert the metal hex wrench that comes with the purchase of the guitar into the adjustment jack at the sound hole of the guitar, and rotate it clockwise to make the neck convex and reduce the string spacing. Rotate counterclockwise, and the neck will be concave, raising the string spacing. In general, the string pitch is too high due to the forward bending of the neck, and it can be adjusted clockwise.

The adjustment of the string pillow is divided into the upper string pillow of the headstock part and the lower chord pillow at the saddle below the sound hole, which is slightly cumbersome and difficult to operate. The adjustment of the string pillow is mainly to reduce the height of the chord pillow by grinding the bottom of the chord pillow through fine sandpaper, so as to achieve the purpose of reducing the chord distance. When sanding, it is necessary to polish as a whole, the bottom of the chord pillow should be kept smooth, not uneven, and the sandpaper should also choose a finer one, and test it in time to avoid overheating.

The guitar has a high string pitch, and it is necessary to turn the wrench in the direction of the 1st string to "tighten" the neck, and there is an irregular bend after the neck is "twisted", which is generally horizontal or vertical's'bend, in this case, you need to find a professional to repair it.

Don't loosen the strings when adjusting the neck, the strings need to be tightened after the strings are sent to have an effect, and repeated tightening of the strings will also hurt the strings.

When adjusting the neck, the amplitude of the wrench can not be too large, the amplitude of the adjustment can not exceed 45 degrees, and the guitar can be erected after turning, which can reduce the force on the neck, and there will be an adaptation process between the neck and the steel bar, which can be adjusted many times.

If the guitar does not adjust the neck for a long time, there may be a situation where the wrench will not move, so it is best to find a professional piano store to adjust it when adjusting it to avoid damaging the neck.

It is very normal for the guitar to have one or two frets in general, which may be affected by humidity and temperature, in this case, it is necessary to determine whether the strings are damaged by external factors.

When the strings are installed, the new strings and the old strings also need to be adapted, so it is necessary to distinguish some situations correctly.

How to install guitar strings:

1. Open the strings and see the tip of the string at one end and the cylindrical tail at the other.

2. Use the tip of the string to pass through the small hole in the bridge behind the acoustic guitar speaker.

3. Put the strings down to the small card slot of the rear bridge, and put the strings to the pillow of the guitar head to destroy the brigade slot.

4. Insert the tip of the string into the twist of the string, tighten the string with your hand, and put the tip of the string into the twist of the string again.

5. Turn the strings and twist them, and adjust the tone of the first string.

Precautions for guitar placement:

1. Don't lean against the wall at the bottom, the upper part can be against the wall, and it's best to find a triangular place, so that it won't be easy to break.

2. Don't lie on the floor, too long, the veneer may cause the panel to sag.

3. Do not go near the heater, the most suitable temperature is about 23 degrees.

4. Don't be too low or too high in the humidity of the guitar, the most suitable humidity for the guitar is 40 50. If the air is too humid, put some desiccant inside the case.

5. It is usually best to hang it on the wall like a physical store (if possible).

6. Be sure to have a piano bag, or piano case: buy a piano cover for mid-range and low-end guitars, which can protect the guitar from dust. High-end guitars buy a case for easy storage of guitars.

7. If you really want to lean on **, you must have the strings facing the place you want to lean, and the reverse side of the guitar is facing outward, and you can't lie down.

8. If you don't use it for more than a month, loosen the string in advance.

If you have a case, put it in the box.

If you use a piano bag, the side of the string is facing the wall, stand upright, and the headstock is against the wall (be sure to stand, you are responsible for pouring).

If you play it often, put it on the stand. If you don't play often, put it in the box. If you put it in a box, it doesn't matter if you put it horizontally or vertically.

If there is a piano stand, put it on the piano stand, and put the piano mainly for fear of bending the neck, don't put the piano against the wall, and if you really want to rely on it, you will lean against the wall in turn