How to set the small pot with channel parameters, and what are the parameters of the small pot throu

Specific parameters such as the reception frequency of the small pot satellite.

If there is no signal in the satellite pot, unplug the signal cable first, and then enter 0000 9999 in the factory reset, and then plug in the signal cable to set it up:

Duzhongxing-9 satellite, Ku-band, village-to-village communication machine, downlink frequency 11880, polarization, left-hand, sign rate 28800, forward error correction 3 4;Free programs are;

**TV Station - General Channel 2100 2101

**TV - Finance Channel 3571 1630

**TV Station - Military & Agriculture 2120 2121**TV Station - Science & Education Channel 2632 2040 Sichuan Kham Tibetan Wei Dao 2140 2141

**TV Station - Social and Legal Channel 3875 2869 Corps TV 1391 2964

**TV - News Channel 1456 3045

**TV - Children's Channel 3978 2877

China Educational Television 1 2638 3644

Beijing Satellite TV 3494 1180

Tianjin Satellite TV 2894 2429

Yunnan Satellite TV 2491 1667

menu, Program Settings, and then Program Input Program Parameters.

It's too general, you'd better be more detailed, and it will be beneficial to solve your problem.

Hello, here's how.

Set parameters: 1. Press the "Menu" button on the remote control to enter the "Main Menu" interface and select "System Settings".

2. Enter the password "9999".

3. Select "Installation and Signal Detection" in the "System Settings" interface (selected by default), and press the "Confirm" button of the remote control twice. Stand behind the satellite dish and let the front of the satellite dish slowly rotate from due south to the direction of the satellite (it is recommended to turn slower than the speed of the second hand of the watch). In the process of rotating, you should always keep an eye on the change of "signal strength" and "signal quality" in the debugging interface of the satellite receiver on the TV, and stop when the indicator signal turns green, indicating that the satellite has been preliminarily identified and the satellite signal has been locked.

4. Network connection settings. IP Settings: , Port Settings: 4567 or 04567.

5. The area code is set to the first six digits of the local ID number.

6. Turn off the power of the set-top box, insert the mobile ** card and smart card, and then turn it on.

7. Select "Base Station Information" in the system settings, and answer according to the exact number.

9. Wait for the base station information to pop up, and the scanned base station information appears on the TV, and click the orange button "Store Confirm".

11. Later, the information box will automatically pop up to prompt "Successful delivery of nuclear issuance", after exiting the menu, the upper right corner of the screen will prompt "During installation, please wait....After 2-3 minutes, the screen will automatically pop up "Installation successful", if this message pops up, please wait patiently for about 10 minutes.

1. Correctly assemble the satellite receiver (pot lid).

2 Connect the feeder properly. zhi high-frequency head-feeder-set-top DAO box.

3 Connect the display correctly.

1.Assemble the satellite receiver correctly.

You just need two people, one watching TV in the house and the other stirring the pot outside.

The parameters of the small pot are not the same. Click the remote control [Menu], click [System Settings], and enter the password "9999" to enter the settings.

Installation method: 1. We first install the satellite pot, which is very simple, only one pot surface and a bracket, just connect it.

2. Take out the wired cable, cut the outer wires at both ends of the cable with scissors, expose the copper wire inside, pay attention to the copper wire to detect about 1cm, trim it as needed, and then cut the cable neatly, and insert the "F" head into the middle of the wire insulation skin and insulating foam column. After the connection, the two ends of the optical cable are connected to the high-frequency head and the signal receiver respectively.

3. After connecting, install the high-frequency head on the satellite pot holder, and pay attention to the front of the high-frequency head facing outward (the end without a wire).

5. After all the above are prepared, turn on the TV and signal receiver to display the signal reception page.

PS: The orientation of the satellite pot must be correct.

The system setting parameters are messed up.,I don't know what the correct one is.,For example, satellite name,Frequency number、Frequency、Symbol rate,Please guide the master View the original post"

The latest 57 sets of program parameters are as follows.

How small a pot? It is required to be above 45 in the southwest direction, and there will be a signal if you move slowly left and right, and then move up and down, left and right, and adjust the signal quality to the maximum.