-
Do you have a toner? You can use it to soak, not too expensive, otherwise it will be too wasteful, and now it is generally soaked with aloe vera water, hydrosol, etc.
-
Soak the face in water with a paper film, which is very moisturizing and hydrating.
-
Pink water bubbles, it's very hydrating in weather like this now.
-
The paper-like film application method is as follows:
1. Find a clean environment, don't be dusty, and avoid the interference of dust in the film. Then turn off the iPad Pro.
2. Use the wet paper in the green package to wipe the dust off the screen and make it spotless.
3. Wipe the paper dry inside the pink package.
4. There will be some stubborn elements, which will be removed and pasted off with dust. It is important to pay close attention to the surface of the screen to see if there is any dust on the surface of the screen and make the final preparations for the film.
5. Uncover one side of the membrane, align it in the direction first, align the horizontal line and the longitudinal line, and slowly fit it from top to bottom. Here you have to be slow, alignment is the most important.
6. Uncover the other half of the film, the key point here is also slow, to ensure that the uncovering will not affect the pasted film. After removing the yellow label, you can feel the matte texture of the paper-like film.
7. After the above links are operated properly, you can squeeze the bubble to finish. No matter how well it is pasted, there will be some small bubbles, and a squeeze will be perfect.
Paper-like film
Paper-like film is similar to the existence of tempered film. To put it simply, it imitates the writing of silver burning wheel characters on paper, which increases friction. The frequency range of the earliest part of the human body is 0 to 5Hz, and the paper-like film reproduces the writing vibration frequency of the paper pencil, and when using the stylus to write on the paper-like film, the nib will inevitably suffer a certain amount of wear.
The paper-like film should be rougher than the matte film, the writing resistance and friction will be much greater than the matte film, and the wear of the tip of the stylus will be greater, but it will definitely affect the display effect of the screen.
-
First, first of all, tear the compression ** and put it into the cup of ** (other cups and bowls can also be used, it is recommended that the opening is larger).
2. Spray pure water on the compression** to let the compression** fully absorb the water.
3. Then squeeze out the water of the compressed ** so that it can absorb the next nutrient water.
4. Pour the toner on the compressed ** to absorb enough water.
5. After that, take it out, open the compression** and apply it to your face.
-
How to use paper
**There are many types of paper, and there are many kinds of materials, including cotton, polyester, and non-woven fabrics; The difference between these materials determines the different effects on the skin. And according to the different areas of each person's face that need skin care, ** paper also has many shapes, some are specifically for the T-shaped area, and some are specifically for the U-shaped area. So, how to use paper?
1. The time it takes for the paper to burn
The usual use time of paper is 10 to 15 minutes, and the paper is not the same as the longer it is used, the better it is for the skin. During this time period, the basic skin has already absorbed the nutrients in the **paper, and there is no point in applying it again, the effect will not increase, and this **paper can be directly removed, and it is not suitable to use it many times after the hall.
2. The use of paper
When using ** paper, you can use some massage techniques to increase the absorption effect of ** essence by muscle culture celery skin, so that the effect is doubled. The general technique is to massage from the center outwards and from the bottom to the top.
3. The correct use of paper
The paper needs to fit well with the skin of the face, so as to achieve better results and maximize the absorption of nutrients by the skin.
To quote Obsidian Star, it is: depending on the technology and understanding, it is best to post it in a dust-free or dust-less place. >>>More
Car film is applied to car glass to control sunlight and ensure safety. >>>More
1. The practice of combining wet and dry stereotype:
1) The combination of dry and wet setting method is a method used when it is impossible to determine whether the consistency of the film and the curvature of the glass is consistent after dry baking. >>>More
Generally, junior technicians can only apply film to the side windows, while only intermediate and senior technicians can apply film to the front windshield with a large curvature. >>>More
When you say operation, I mean construction.
According to the needs of the project, the film is divided into two types: the film on the glass of the existing building and the uninstalled building glass film. >>>More