How to operate the glass film? The right way to apply glass films

When you say operation, I mean construction.

According to the needs of the project, the film is divided into two types: the film on the glass of the existing building and the uninstalled building glass film.

1. When installing the film on the glass of the existing building, the objects that hinder the construction should be removed and removed. The on-site construction site should be kept clean, and waterproof canvas or plastic film should be used to protect the film glass from pollution; When applying the film in the glass deep processing workshop, the film application workshop should be kept clean and tidy to prevent dust and other things from sticking on the glass surface.

1. Before the film, use a special knife to remove the mud, paint, silicone glue and other adhesives on the glass. Wipe off dust around the window frame with a soft, lint-free cotton cloth and wipe all window corners, notches and accessories.

2. After the dirt on the glass surface is removed, fully moisten the glass surface with a special cleaning solution, evenly scrub the entire surface, and wash away the oil stains and floating dust on the glass surface.

3. Before the glass surface is removed, the glass surface seriously polluted by sand particles should not be scrubbed with cleaning solution; Special tools should be used when scraping and shoveling adhesive objects on the glass surface, and accessories such as glass, window frames and sealing strips should not be damaged.

4. Dust and sewage should be prevented from infiltrating into the surface of the window frame and glass along the edge of the window frame, and the frame should be sealed with masking tape before construction.

5. After cleaning, use the mounting glue to evenly wet the whole glass for the first time, and then use an ordinary rubber scraper to scrape off the mounting glue on the glass surface to completely remove the dust and sticky dirt left on the glass.

6. After spraying the mounting glue evenly on the entire glass surface again, immediately float the film onto the glass surface and slide to the correct position.

7. Use a special scraper tool to carefully and evenly scrape off most of the mounting glue under the film, and prevent the moisture and air on the edge of the film from penetrating under the film again. At the same time, make sure that there are gaps in the edges of the glass or windows.

8. When the glass is completed after the construction of the film, the surface of the film and the window frame can be cleaned with a window film cleaner that does not contain ammonia ions.

In addition, one month after the film is applied, the sealant matching the film can be applied.

Waterproof measures should be taken after the construction of the glass film outer sticker, so as not to affect the drying of the installation glue and sealant by rain.

Hello: If you want two people to paste, find an old cloth or towel in advance. Two people spread it and stick it on one side, then one person pulls the film, and the other person gently wipes it little by little with a cloth, from front to back, little by little, and it will soon be pasted.

1. First of all, spread the large towel on the ground at the position of the film to avoid damage to the floor or paint film, the glass must be absolutely clean, and the part to be filmed must be sprayed with water on the glass, which needs to be cleaned repeatedly.

2.Use glass cleaning glue to scrape from top to bottom, remove the dust on the glass from the middle to both sides, and the whole glass should be sprayed with clean water every time it is scraped, and finally scraped out the stagnant water with a plastic scraper. Make sure that the glass is smooth and clean before applying the film.

3.It is best not to clean the glass for the time being after the film is finished!!

Meiquan film industry has a professional construction team!!

A full range of products coupled with international construction and sincere after-sales service is our leading huge advantage!!

You can go to the official website of AAA glass film in the United States to watch the film tutorial.

The correct way to apply glass is to prepare a glass film and related film tools in advance, such as rags, rulers, knives, water scrapers, etc.

1. First of all, cut the glass film according to the size of the glass.

2. Wipe the surface of the glass with alcohol or dish soap, and then tear off the protective layer of the glass film.

3. Spray a little water on the glass, and then stick the glass film on the glass.

4. Use a scraper to fix the position of the glass film and the glass, and then use the scraper to discharge the water and air between the glass film and the glass.

5. Finally, use a knife to cut the glass into the film on the glass.

Before the glass film, the film cloth should be cut first, about one centimeter higher than the length of the glass, the first can avoid crookedness, and then the glass will be cleaned, sprayed with water after cleaning, used to reduce the viscosity of the glass sticky film, the viscosity will not be affected after drying, after removing the inclined release film, you can sprinkle water on the back of the glass film, which is convenient for construction, when paving the glass film cloth, you can move the film to the appropriate position, measure the size, up and down, left and right one-time alignment, sprinkling is to avoid no alignment, You can tear it off again for pasting, and then use a scraper to scrape the bubbles out and cut off the excess.

1. First of all, prepare a watering can, add a little baking soda and white vinegar to it, then add a certain amount of water, stir evenly and spray it on the surface of the film. After waiting for a while, it will get wet. Then use a knife to scrape off the film on the surface of the glass, prepare a dry rag, dip a little liquor to wipe it, and the leakage can effectively remove the source film on the glass surface.

2. If there are still some tiny marks or small marks, take a dry rag dipped in a little turpentine and wipe it repeatedly to remove the excess traces on the surface.

The correct method and steps for glass film are as follows:

1. Measure the size of the window glass first, and then use a utility knife to cut the glass film according to the size and quantity of the window glass. In order to make it more convenient to paste the film later, it is recommended that when you cut the glass film, it is best to cut the size of the glass film by about 1 cm to 2 cm.

2. Before pasting the glass film, it is generally necessary to clean the window glass first. You can fill a watering can with some water, drop some dish soap into the watering can, shake it sufficiently, and then use the watering can to spray continuously on the glass, and then use a water scraper to scrape the water stains on the glass.

3. Before pasting the glass film, some water should be sprayed above and below the glass film to avoid electrostatic reaction of the glass film. When pasting the glass film, you should first tear off the protective layer of the glass film, then spray some water on the glass, and then paste the glass film on the glass, and then use a scraper to fix the position of the glass film, so as to avoid the glass film from slipping.

4. Next, the scraper should be used to squeeze out the water between the glass film and the glass, and the scraping should be carried out from top to bottom. After squeezing and scraping, the glass film should be carefully checked for air bubbles, if there are, the air bubbles should be punctured with a blade, and then the air bubbles should be scraped flat with a scraper. Finally, use a utility knife to cut off the glass film beyond the position of the glass.

The method of pasting the glass film: 1. First cut the glass film according to the size of the glass. 2. Scrub the glass surface with alcohol or dish soap, and then tear off the protective layer of the glass film.

3. Spray some water on the glass and stick the glass film on the glass. 4. Then use a scraper to fix the glass film, and then use a scraper to squeeze out the water between the glass film and the glass. 5. Finally, use a utility knife to divide the glass on the glass film.

Glass film Yeqing refers to a kind of film in the home building materials market, which has a variety of colors, energy saving and environmental protection, and is mainly used to decorate indoor and outdoor glass.

Basic structure

The most basic composition of glass film is a polyester substrate (PET) with an anti-scratch layer (HC) on one side and a adhesive layer and protective film on the other. Glass film is usually composed of single or multiple layers of PET sandwich, and the thickness is as follows:

2mil (etc.; Considering safety and ease of construction, the thickness of the substrate of the membrane should be more than 2mil.

PET is a material with strong durability, strong and moisture resistance, high and low temperature resistance and good pre-permeability. It is clear and transparent, and has been treated by various processes such as metallization coating, magnetron sputtering, and sandwich synthesis to become films with different characteristics. Specialized manufacturers of membranes usually use their own proprietary adhesives for sandwich synthesis and installation of adhesive layers, mainly pressure-sensitive adhesives and water-molecule-activated adhesives.

Isolate ultraviolet rays, and people and things are bathed in better sunlight

The glass film can block more than 99% of the harmful ultraviolet rays that pass through ordinary glass, and effectively protect indoor cultural relics, historical materials, crafts, and book collections from fading, aging, and prolonging their life. Far higher than other glass products and sunscreens, apply a film to protect from UV rays, extend the use of furniture and accessories in your home, and enjoy better sunlight.

The steps to apply the glass film are as follows:Material preparation: scissors, glass film, rags, watering cans, scrapers and blades, etc.

1. Reserve 2-3cm when cutting the film for final trimming.

2. Wipe the glass clean, do not leave dust and stains, and then spray a large amount of water on the glass with a watering can (to the extent that the water can flow down).

3. Tear off the back film of the film. Apply the film to the glass from top to bottom, left to right. If there is a mistake in the middle, there is no need to worry, the non-adhesive film can be re-applied, and the film can be moved until the preparation position is determined. Person-type.

4. After the film is glued, it is normal for bubbles to appear, as long as the bubbles are scraped clean with a scraper.

5. After the bubbles are processed, use a blade to cut off the excess part.