-
Anonymous users2024-02-07Generally, junior technicians can only apply film to the side windows, while only intermediate and senior technicians can apply film to the front windshield with a large curvature.
Before the film, it is necessary to check whether the installation of the window glass is intact and the integrity of the car glass to ensure that the subsequent film work can operate normally.
Be sure to cover the necessary parts of the car before applying the film to prevent liquid from penetrating. Sprayed cleaning fluids and lubricating fluids can affect trim parts such as automotive electronics and interior seats.
Wash the interior and exterior surfaces of the windows before applying the film (focusing on the interior surfaces and glass sealant areas). This is mainly to eliminate the dirt or other object construction quality problems between the heat insulation film and the window glass after the film, and ensure that the film and glass can be perfectly combined.
The membrane is pre-cut. Use a ruler to measure the size of the front and rear windshields, and cut the film according to the measured size. (The professional film mechanism is through the computer, which is tailored according to the model).
Spray the installation fluid. Dust spots can be avoided and corrosion at the edges can be reduced, resulting in the desired viscosity and better application results.
Dry roasting, wet roasting shaping. The film is dry-roasted first so that the film can be fully pre-shrunk. In order to further improve the adhesion of the heat insulation film, it is also necessary to wet bake and shape the heat insulation film.
Extrusion of the installation fluid: In the process of using the wiper to remove the installation fluid, try to scrape the installation fluid between the heat insulation film and the window glass, which can reduce the drying time of the heat insulation film and obtain a better bonding effect, overall performance and visual effect.
Check after sticking. "Three looks and one attention": look at the entire heat insulation film to see if there is any dust and bubbles, see whether the corners are firmly glued, and sit in the car to see if there are any places that affect the line of sight (especially the front windshield and side windshield). After the film, it is recommended not to raise or lower the glass arbitrarily within 48 hours.
The most important thing to pay attention to when applying the film is the use of hair dryer, if you blow this place for a long time, it will cause the glass to crack due to uneven heating. Therefore, it is necessary to find those professional authorized stores for the film, so that the quality of the film will be the best and the danger of glass cracking can be avoided.
Also, the car film is best in rainy weather, and when it is pasted on rainy days, there is very little dust in the air, which has certain benefits for aesthetics.
-
Anonymous users2024-02-06Tutorial on sticking car film by yourself.
The first step is to prepare for the car film: cleaning and installing interior protection.
In order to prevent the production of tiny impurities during the film, the car is usually cleaned all over the body when the car film is applied, first take a look at the car windows before the car film:
Remind everyone that you must do a good job of protecting the car interior before the car film, especially the new car; Because it is inevitable that the car interior will be soiled during the film application process, it is necessary to prepare for it in the early stage
The second step is to tailor the car film according to the size of the window.
Film cutting is an important process of car film; According to the CAR2100 evaluation, the size of the car film is generally determined according to the specific size of the window, and the size is slightly larger than the size of the window.
Tutorial on sticking car film by yourself.
The third step is the cleaning of the front and rear windshields.
In addition to cleaning the whole vehicle, it is necessary to remind everyone that it is also necessary to carefully clean the window glass again; When cleaning, the car is generally scraped repeatedly with two kinds of scrapers (hard scraper and soft scraper). Now the car film will be operated in the dust-free workshop, which is also to prevent impurities from being generated in the car film and affecting the effect of the film
Step 4: Wrap and bake film, wet film.
When cutting the film, the staff will spray soapy water on the car window glass, so that in order to better paste the car film, after the adhesive layer of the car film is uncovered, it should be carefully glued to the inside of the car window, and the edge distance between the car film and the car window should be adjusted under the lubrication of soapy water to ensure the overall appearance.
The film has officially begun.
The baking film in the film is mainly to fix the car film and shape the car film by heating
After the film is completed, the staff will also check the effect of the film, on the one hand, it is to cut the corners; On the other hand, the staff will use the scraper mentioned above to scrape out the remaining blisters in the film, so that the car film and the window glass are completely attached. After that, wipe the removed water stains with a towel with excellent water absorption, and the finished car film and car film can create a perfect mirror effect.
-
Anonymous users2024-02-051.Car film can make the car look as shiny as new, which is one of the basic contents of car maintenance. So how do you stick your own car film? Let's take a look at the tutorial for car film. 2.Self-adhesive film tutorial.
3.Step 1: Preparation before car filming: clean and install interior protection.
4.In order to prevent the formation of microscopic impurities during the lamination, the entire body is generally cleaned during the lamination. Look at the window before applying the film:
6.Secondly, the film is cut according to the size of the window.
7.Film cushioning is an important process of car film; According to the evaluation of CAR2100, the cutting size of the car film is generally determined according to the specific size of the car window, and the size is slightly larger than the car window to cut.
8.Self-adhesive film tutorial.
9.Step 3: Clean the front and rear windows.
10.In addition to vehicle washing, it is also important to remind everyone that the window glass needs to be carefully cleaned again. When washing, the car is usually scraped repeatedly using two types of scrapers (hard scraper and soft scraper).
Now the car film will be operated in the dust-free workshop to prevent impurities from being generated in the car film and affecting the effect of the film
11.Step 4: Wrap, bake, wet film.
12.When the film is cut, the staff will spray soapy water on the window glass. In this way, in order to better paste the car film, after the adhesive layer of the car film is removed, it should be carefully pasted on the inside of the car window.
Under the lubrication of soapy water, the distance between the edge of the car film and the car window can be adjusted to ensure the overall appearance.
13.The movie has officially begun.
14.The intermediate baking film is mainly used to fix the automobile film and shape the automobile film by heating;
15.After the film is filmed, the staff will also check the effect of the movie, on the one hand, cutting corners; On the other hand, the staff will use the scraper mentioned above to scrape off the remaining blisters in the film and let the film completely adhere to the window glass. After that, wipe the removed water stains with a highly absorbent towel, and the finished car film and car film can create a perfect mirror effect.
17, 1.Explosion-proof. The base layer of the membrane is polyester film, which is very tear-resistant and anti-breakdown, which can prevent accidental glass breakage from causing secondary injury to drivers and passengers.
18, 2.Thermal and sun protection. The film can solve the large amount of heat generated by infrared rays, and the body temperature is greatly reduced, as well as the temperature in the car.
Reduce the energy consumption of air conditioners. The cooling loss of the heat shield air conditioner can be compensated, which can prevent the temperature in the car from being too high to a certain extent, and achieve the effect of saving fuel consumption and reducing the energy consumption of the air conditioner to a certain extent.
20, 4.UV protection. Medium and long wavelengths of UV light can penetrate thick glass, and a layer of heat insulation film can block 99% of UV rays.
Prevent damage and reduce the aging of car interiors. For example, the front screen of 3M Jingrui 70 can block ultraviolet rays, which is 56 times that of SPF40.
21, 5.Anti-glare. Keep your eyes comfortable. Reduce accidents caused by the glare factor.
22, 6.Create a private space. After the film, you can't see the inside of the car clearly, but it does not affect the scenery in the car (Reference|.)**)。This way, you can effectively protect your privacy and security.
23, 7.Improve aesthetics. According to personal preference, the car can be personalized by wrapping it.
-
Anonymous users2024-02-04Clean the body and keep it dry. 2. Determine the location that needs to be pasted. Under normal circumstances, slowly apply while scraping flat with a tool and removing the bottom paper.
3. If the graphics are really not big, you can also tear off all the transparent transfer film and stickers before pasting. But care must be taken not to accidentally adhesion.
4. After pasting, scrape and press several times. Remove the transparent transfer membrane.
5. Draw a knife with a utility knife on the door and sewing the car, and wrap it inward. Rowing Sparrows.
Main advantages: The automotive film is a vacuum thermal evaporation film, which adopts a vacuum thermal evaporation process, which evaporates the aluminum layer on the substrate to achieve the thermal insulation effect. This is also commonly referred to as the field of mammoto metal film, which has a relatively long-lasting thermal insulation, but the weakness is that the clarity is not high, which affects the comfort of the field of vision, and another prominent weakness is the high reflection.
Wrapping film is a technical job, and a car beauty shop asks a professional filmmaker to pay thousands of yuan a month. You can't learn just by watching tutorials without practice. >>>More
At present, the color change film is mainly divided into two categories: domestic and imported. The domestic color change film is not as good as the imported color change film in terms of post-construction effect and durability. If you don't have a long-term color change demand, and you just want to change the color of the body to entertain yourself, then the cheapest domestic color change film is the best choice. >>>More
It takes about two or three months to learn car wrap.
Generally, if you go to school, it will be about the same for two or three months. Car film is a difficult technical job, the process of film will also affect the final effect, if not necessary, it is best to leave the film work to an experienced master to complete. However, some car owners are hands-on. >>>More
Many people are very confused about whether to apply the film, some people say that it must be pasted, and some people say that it is not good to put it on. >>>More
The car film is to be pasted on the inside of the car glass, the reason is very simple, and then there will be no wind and rain on the inside, and the film will not be subject to too much external interference during the use of the film, because the film is glued, without the baptism of wind and rain, it must be very firmly pasted, and it will not be affected on the inside when used. Since the film is attached to the inside of the car glass, the wiper will definitely not scratch the glass film, because the wiper is on the outside, and there is no need to remove the car glass when pasting the car film. Car film is actually a very technical work, much more difficult than architectural film, because the car glass has a curvature, and the architectural glass has a curvature is not much, after a film is cut, it is necessary to bake and shape according to the curvature of the glass, and then accurately cut the film, and then the film is applied internally.